English dropdown-ico

Manual Greenheck PVF

8 pages 0.1 mb
Download

Go to site of 8

Summary
  • Greenheck PVF - page 1

    Part # 461006 MODEL PVF INDIRECT GAS FIRED FURNACES FOR ENERGY RECOVER Y UNITS Installation, Operation and Maintenance Manual ® RET AIN THESE INSTRUCTIONS FOR FUTURE REFERENCE W ARNING!!! Improper installation, adjustment, alteration, service or maintenance can cause injury or death. Read the installation, operating and maintenance instructions th ...

  • Greenheck PVF - page 2

    1. Single furnaces (furnace input 100 to 400 MBH) have a single 3 ⁄ 4 inch connection. Double furnaces (furnace input 500 to 800 MBH) have two 3 ⁄ 4 inch connections, and triple furnaces (furnace input 1050 to 1200 MBH have three 3 ⁄ 4 inch connections. 2. When connecting the gas supply, the length of the run must be considered in determining ...

  • Greenheck PVF - page 3

    1. Installation of wiring must conform with local building codes. In the absence of local codes, installation must conform to the National Electric Code ANSI/NFPA 70-Latest Edition. Unit must be electrically grounded in conformance with this code. In Canada, wiring must comply with CSA C22.1, Canadian Electrical Code. 2. All furnaces are provided w ...

  • Greenheck PVF - page 4

    Power -up/Standby After power is supplied to the unit: 1. The ignition control will reset and perform a self- check routine. 2. The diagnostic LED will flash for up to four seconds. 3. The ignition control will begin scanning the thermostats. Heat Mode When the thermostat or discharge temperature controls call for heat: 1. The ignition control will ...

  • Greenheck PVF - page 5

    Setting Manifold Pressure for Two Stage Gas Control 1. Set the unit to high fire by setting the discharge temperature control or thermostat to its maximum setting. If the ambient temperature is warm, the unit may not stay at high fire. 2. Measure the burner manifold pressure at the manifold pressure test port (see Control Center Layout on page 3) u ...

  • Greenheck PVF - page 6

    1. Set the unit to high fire by placing a jumper between terminals 7 and 8 on the Maxitrol amplifier. 2. Measure the burner manifold pressure at each furnace at the pressure test port (see Figure 2) using a high quality manometer that can measure low gas pressures. The pressure at high fire should be 3.5 in. wg for natural gas and 10.0 in. wg for L ...

  • Greenheck PVF - page 7

    Ignition Control Diagnostic LED During normal operation, the LED is shut off. The LED will be on or flashing during a fault condition. If a fault condition is occurring, turn the unit off and on again. If the LED is still flashing, refer to the following troubleshooting section. LED Indication Error Mode Steady on Internal control failure 1 flash A ...

  • Greenheck PVF - page 8

    Combustion Blower Motor Motor maintenance is generally limited to cleaning. Cleaning should be limited to exterior surfaces only. Removing dust and grease build-up on the motor housing assures proper motor cooling. Use caution and do not allow water or solvents to enter the motor or bearings. Under no circumstances should motors or bearings be spra ...

Manufacturer Greenheck Category Furnace

Documents that we receive from a manufacturer of a Greenheck PVF can be divided into several groups. They are, among others:
- Greenheck technical drawings
- PVF manuals
- Greenheck product data sheets
- information booklets
- or energy labels Greenheck PVF
All of them are important, but the most important information from the point of view of use of the device are in the user manual Greenheck PVF.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Greenheck PVF, service manual, brief instructions and user manuals Greenheck PVF. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Greenheck PVF.

Similar manuals

A complete manual for the device Greenheck PVF, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Greenheck PVF by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Greenheck PVF.

A complete Greenheck manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Greenheck PVF - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Greenheck PVF, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Greenheck PVF, that we can find in the current document
3. Tips how to use the basic functions of the device Greenheck PVF - which should help us in our first steps of using Greenheck PVF
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Greenheck PVF
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Greenheck PVF in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Greenheck PVF?

Use the form below

If you did not solve your problem by using a manual Greenheck PVF, ask a question using the form below. If a user had a similar problem with Greenheck PVF it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)