-
DeWalt DW717 - page 1
DW717- XE 254 mm (10") DOUBLE BEVEL SLIDING COMPOUND MITER SA W INSTRUCTION MANUAL Questions? See us on the World W ide Web at www .dewalt.com ...
-
DeWalt DW717 - page 2
T ABLE OF CONTENTS DOUBLE INSULA TION INSTRUCTIONS................................................................................................. ...........1 SAFETY INSTRUCTIONS FOR ALL TOOLS ......................................…………………………………………1 ADDITIONAL SAFETY RULES ....................................……? ...
-
DeWalt DW717 - page 3
1 Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injur y . WARNING: Indicates a potentially hazardous situation which, if not ...
-
DeWalt DW717 - page 4
2 2 • ST ABILITY . Make sure the miter saw is placed on a secure suppor ting sur face and does not slip or move during use. If the mobility kit is installed, raise the moveable caster(s) so saw is in its stationar y position. • FOLL OW ALL WIRING CODES and recommended electrical connections to prevent shock or electrocution. Protect electric su ...
-
DeWalt DW717 - page 5
3 3 Electrical Connection The electric motor has been designed for one voltage only . Always check that the power supply corresponds to the voltage on the rating plate. 230 V AC means your tool will operate on alter nating current. As little as 10% lower voltage can cause loss of power and can result in over heating. All D E WAL T tools are factor ...
-
DeWalt DW717 - page 6
4 Unpacking Y our Saw Check the contents of your miter saw car ton to make sure that you have received all par ts. In addition to this instr uction manual, the car ton should contain: 1. One DW717 miter saw . 2. One D E W AL T 10" (254 mm) diameter saw blade. 3. One blade wrench in wrench pocket shown in Figures 4 and 9. 4. One DW7053 Dustbag ...
-
DeWalt DW717 - page 7
5 4. Depress the spindle lock button (C) while carefully rotating the saw blade by hand until the lock engages. 5. Keeping the button depressed, use the other hand and the wrench provided to loosen the blade screw . (T urn clockwise, lef t-hand threads) 6. Remove the blade screw (E), outer blade clamp (F) and blade (G). The inner blade clamp (I), m ...
-
DeWalt DW717 - page 8
6 6 Adjustments WARNING: T o reduce the risk of serious personal injur y , turn off the tool and disconnect it from the power source before attempting to move it, change accessories or make any adjustments accept as written in laser adjustment instr uctions. NOTE: Y our miter saw is fully and accurately adjusted at the factor y at the time of manuf ...
-
DeWalt DW717 - page 9
7 when the bevel lock handle is tightened. T o adjust the bevel lock handle, remove the screw in the center of the handle. Carefully pr y off the handle using a flat bladed screwdriver . Reorient and install the handle such that it will hold the bevel when tightened. Install and tighten screw . SLIDE STOP (FIG. 10B) The slide stop control positions ...
-
DeWalt DW717 - page 10
8 8 When cutting anything larger than 111.8 mm (4.4") [76.2 mm (3") 45º miter] use an out-down-back motion with the rail lock knob loosened. Pull the saw out, toward you, lower the saw head down toward the workpiece, and slowly push the saw back to complete the cut. Do not allow the saw to contact the top of the workpiece while pulling o ...
-
DeWalt DW717 - page 11
9 9 TO INST ALL CLAMP 1. Inser t it into the hole behind the fence. The clamp should be facing toward the back of the miter saw . The groove on the clamp rod should be fully inser ted into the base. Ensure this groove is fully inser ted into the base of the miter saw . If the groove is visible, the clamp will not be secure. 2. Rotate the clamp 180? ...
-
DeWalt DW717 - page 12
10 10 BEVEL SETTING TYPE OF CUT 33.85° Lef t LEFT SIDE, INSIDE CORNER: 1. T op of molding against fence 2. Miter table set right 31.62° 3. Save lef t end of cut 33.85° Right RIGHT SIDE, INSIDE CORNER: 1. T op of molding against fence. 2. Miter table set at lef t 31.62° 3. Save right end of cut 33.85° Right LEFT SIDE, OUTSIDE CORNER: 1. T op of ...
-
DeWalt DW717 - page 13
11 11 CUTTING LARGE MA TERIAL Occasionally you will encounter a piece of wood a little too large to fit beneath the blade guard. If this occurs, simply place your right thumb on the upper side of the guard and roll the guard up just enough to clear the workpiece, as shown in Figure 23. Avoid doing this as much as possible, but if need be, the saw w ...
-
DeWalt DW717 - page 14
12 12 MAINTENANCE DO NOT use lubricants or cleaners (par ticularly spray or aerosol) in the vicinity of the plastic guard. The polycarbonate material used in the guard is subject to attack by cer tain chemicals. 1. All bearings are sealed. They are lubricated for life and need no fur ther maintenance. 2. Periodically clean all dust and wood chips f ...
-
DeWalt DW717 - page 15
13 13 10 10 10 20 20 20 30 30 30 40 40 40 50 50 50 60 60 60 70 70 70 80 80 80 T ABLE 1: COMPOUND MITER CUT (POSITION WOOD WITH BROAD FLA T SIDE ON THE T ABLE AND THE NARROW EDGE AGAINST THE FENCE) SET THIS MITER ANGLE ON SAW ANGLE OF SIDE OF BOX (ANGLE A) SQUARE BOX 6-SIDED BOX MITER DEGREE SETTING BEVEL DEGREE SETTING SET THIS BEVEL ANGLE ON SAW 8 ...
-
DeWalt DW717 - page 16
D E W AL T Industrial T ool Co., 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (03 8720 5100) • 5 T e Apunga Place, Mt W ellington, New Zealand (09 259 1111 ) (MAR08) Par t No. 658043-00 DW717- XE Copyright © 2008 D E WAL T The following are trademarks for one or more D E WAL T power tools: the yellow and black color scheme; the “D” shap ...
Do you have a question concerning DeWalt DW717?
Use the form below
If you did not solve your problem by using a manual DeWalt DW717, ask a question using the form below. If a user had a similar problem with DeWalt DW717 it is likely that he will want to share the way to solve it.