-
Eagle Electronics Eagle View - page 1
INST ALLA TION AND OPERA TION INSTRUCTIONS Eagle V iew TM ® ...
-
Eagle Electronics Eagle View - page 2
Copyright © 1996, 1997 Eagle Electronics All rights reser v ed. Eagle View ™ is a tr ademark of Eagle Electronics Eagle ® is a registered trademar k of Eagle Electronics W ARNING! USE THIS UNIT ONL Y AS AN AID T O NA VIGA TION. A CAREFUL NA VI- GA T OR NEVER RELIES ON ONL Y ONE METHOD T O OBT AIN POSI- TION INFORMA TION. Never use this pr oduct ...
-
Eagle Electronics Eagle View - page 3
INTRODUCTION .......................................................................................................... 1 INST ALLA TION ............................................................................................................. 2 BRACKET INST ALLA TION .............................................................................. ...
-
Eagle Electronics Eagle View - page 4
NA VIGA TION ................................................................................................................ 35 NA VIGA TE T O A WA YPOINT .................................................................................. 35 NA VIGA TE TO A CURSOR LOCA TION .................................................................. 35 NA VI ...
-
Eagle Electronics Eagle View - page 5
1 Congratulations! Y ou hav e purchased one of the finest 12-channel GPS receivers Eagle™ has e ver made. With its large LCD screen, easy to use menus, and out- standing perf or mance, we think you’ll be happ y with your Eagle Vie w™ f or many years . GPS works from satellites that transmit inf or mation to the wor ld at very high frequencies ...
-
Eagle Electronics Eagle View - page 6
2 you outstanding position and na vigation information. Most people are amazed when the y actually use a GPS receiver and see what it does . Please sit down with the unit and this man ual and familiarize y ourself with them bef ore using the Eagle View in the “real w orld”. A simulator is built in, which lets you pr actice. INST ALLA TION INSTA ...
-
Eagle Electronics Eagle View - page 7
3 Gimbal Bracket Washer Gimbal Knob Eagle View Attach the Eagle View to the gimbal bracket using the supplied gimbal knobs and washers as shown below. ...
-
Eagle Electronics Eagle View - page 8
4 WHITE TO EA GLE VIEW 2-AMP FUSE GREEN BLACK RED 12-V OL T BA TTERY EAGLE VIEW TRANSMIT (NMEA) EAGLE VIEW RECEIVE (NMEA) PO WER The Eagle View will oper ate from a 12-v olt DC system. (9 to 15 volts DC .) Y ou can connect the pow er cable to an accessory buss under the dash, how ev er , to keep electrical noise interf erence to a minimum, we recom ...
-
Eagle Electronics Eagle View - page 9
5 ANTENNA The Eagle View’ s antenna can be mounted on any flat surf ace , pro vided you ha ve access behind the surf ace for the mounting scre ws. A magnet is also supplied that can be epo xied to the bottom of the antenna, allowing it to be used on off-road v ehicles. A pole mount adapter lets y ou mount the antenna on a pole or s wiv el mount. ...
-
Eagle Electronics Eagle View - page 10
6 After drilling the holes, pass the o-ring ov er the antenna cable and press it into the groov e on the bottom of the antenna housing. Now attach the antenna to the mounting surf ace, using 4mm screws and the supplied lock w ashers. Route the cable to the Eagle Vie w and the antenna installa- tion is finished. Magnet Mount A magnet lets you tempor ...
-
Eagle Electronics Eagle View - page 11
7 KEYBO ARD The k eyboard has twelv e keys. The arrow k eys are tied to most of the f eatures, letting you easily mo ve the plotter’ s cursor , navigate through the menus , mak e selections from menus , and other tasks. The WPT k ey lets you create , sav e, and recall wa ypoints and routes. The MODE ke y switches the unit betw een the three major ...
-
Eagle Electronics Eagle View - page 12
8 OPERA TION T urning Po wer On T o tur n the Eagle View on, simply press the PWR ke y . A screen similar to the one at right appears. Read the message on the screen, then press the EXIT ke y to erase it. The Eagle View is now ready f or use. MENUS Most of the Eagle View’ s adjustments and features are f ound on “men us”. Pressing the MENU ke ...
-
Eagle Electronics Eagle View - page 13
9 Once the Eagle View loc ks on to the satellites and finds your position, it stores the satellite data in its memory . The next time y ou use the unit, it should take much less time to loc k on. T o use your Eagle View , first make certain you ha ve a clear vie w of the sky , free from any obstructions such as trees, car por t, or a co v ered boat ...
-
Eagle Electronics Eagle View - page 14
10 arrow k ey . The screen shown at right ap- pears. Using the down arro w key , highlight the “Initialize GPS Receiv er” menu, then press the right arrow ke y . The screen shown belo w appears. This is the GPS initialization screen. The position, altitude, time , and date the Eagle View is currently using to find the satellites is shown at the ...
-
Eagle Electronics Eagle View - page 15
11 Now change the local time and date if they’ re incorrect on this screen. (Don’t worry about altitude.) When ev er ything is acceptabl e, press the EXIT key repeat- edly to return to a mode screen. The Eagle View will instantly use the data you entered to find the satellites in the sky . (The unit knows which satellites will be a vailab le at ...
-
Eagle Electronics Eagle View - page 16
12 as "GRP" (groups). For e xample, Group A is the first windo ws group on the MODE menu.) Press the right arro w ke y to see more screens on each mode. When the desired screen appears, press the EXIT k ey to clear the menu. Note: F or a list of abbreviations used on the displa ys, see the bac k of this manual. Navigation Screens There ar ...
-
Eagle Electronics Eagle View - page 17
13 348°. The line extending behind the ar- row in the center sho ws your trac k his- tor y , or path you’v e tra velled. Y our speed ov er ground or Ground Speed (GS) shows in the digital bo x to the right of the circle. The screen looks like this when y ou’re not navigating to a w aypoint. (See page 35 f or information on waypoint na viga- ti ...
-
Eagle Electronics Eagle View - page 18
14 Nav Screen #2 The navigation screen sho ws navigation inf or mation in large digital n umbers. T o view this screen, press the MODE k ey , then press the up arrow k ey until the b lack bo x surrounds the “NA V 1” label. Now press the right arro w ke y . A screen similar to the one at right appears. Press the EXIT ke y to erase the mode menu. ...
-
Eagle Electronics Eagle View - page 19
15 row k ey to mov e the black bo x to the "PLO T" label. Now press the right arrow or left arro w key to select plot 2. This screen (as shown at the bottom of the pre vious page) has navigation data displa yed on the right side of the screen in digital numbers . This data is active whene v er you’ve recalled a wa ypoint. Press the EXIT ...
-
Eagle Electronics Eagle View - page 20
16 Record T rail On / Off The line e xtending from the present po- sition diamond on the plotter is call the plot trail. As each dot on the trail is placed on the screen, it’ s also saved in memory . The plot trail recording can be turned off, if desired. T o tur n it off , press the up or do wn arrow ke y until the “Record T rail” men u is h ...
-
Eagle Electronics Eagle View - page 21
17 In the trac k-up vie w at right, the present position mov es straight towards the top of the displa y . As you can see , the an- chor icon is now sho wn in its proper ori- entation - to our right. A "N" shows to help you see which direction is north when the trac k-up mode is on. Remember , in the track-up mode , the screen rotates as ...
-
Eagle Electronics Eagle View - page 22
18 Grid Lines The Eagle View can place grid lines on the plotter to help y ou see your position, or the position of wa ypoints and icons. T o do this, highlight the “Gr id Lines” label on the “Plotter Opts” menu, then press the right arrow ke y to tur n them on. Press the EXIT ke y to exit this men u . A plotter screen similar to the one at ...
-
Eagle Electronics Eagle View - page 23
19 press the ENT k ey . The plotter screen re- appears with the icon at the cursor's lo- cation. Press the EXIT key to er ase the cursor . On the screen shown at r ight, the large fish icon was selected and placed at the cursor location. Erase Icons T o erase an icon from the screen, first press the MENU k ey , then select the “WPT/Icon Opts ...
-
Eagle Electronics Eagle View - page 24
20 the icon. If you wish to delete another icon, mov e the cursor ov er it and press the ENT ke y . When you’ re finished, press the EXIT key to er ase the cursor . WINDO WS This f eature gives y ou 15 diff erent groups of windows so y ou can use the best navigation displa y f or y our situation. T o use the windows f eature, press the MODE k ey ...
-
Eagle Electronics Eagle View - page 25
21 COURSE DEVIA TION INDICA T OR (CDI) The CDI shows y our distance to the left or right of the desired course. Y ou must recall a wa ypoint or run a route to use the CDI. The arrow in the center of the bo x shows the direction to the destina- tion. For e xample, if you’ re tra velling straight tow ards the destination, the ar- row points str aig ...
-
Eagle Electronics Eagle View - page 26
22 CLOCK Whene ver a cloc k, timer , or alar m is sho wing on a display , new items appear in the list when you press the MENU k e y . These items let you set the cloc k’ s time , alar ms , or the timers. Clock Set If the time shown on the cloc k display is not your local time , change it using the “Clock Set” function. T o do this, press the ...
-
Eagle Electronics Eagle View - page 27
23 Timers The Eagle Vie w has two timers built in. One is a countdo wn timer and the other is a count-up timer . The countdown timer counts down from the time you put in to z ero . The count-up timer starts at zero and counts up to the time y ou entered. T o set either timer , first switch to a win- dow g roup with a timer. Ne xt, press the MENU k ...
-
Eagle Electronics Eagle View - page 28
24 This is the plot-2 edit screen. The “BRG” bo x in the upper r ight corner flashes, which means it’ s ready for change . If you don’t want to change this bo x, simply press the up or down arro w key to mo ve to the bo x that you do want to change . In this e xample, w e will change the BRG bo x to ground speed, or GS. T o do this, simply ...
-
Eagle Electronics Eagle View - page 29
25 Saving The Cursor P osition as a Wa ypoint When the cursor is showing on the plotter and y ou press the WPT ke y twice, the Eagle View puts the cursor’ s position into the first av ailable w aypoint n umber . A message appears on the displa y telling you the wa y - point number it just used. W ait a fe w seconds and the menu will clear automat ...
-
Eagle Electronics Eagle View - page 30
26 Highlight the “Sav e Position As” label as shown below left and press the right arrow ke y when you’ re at the location you wish to sa ve . This saves your present position under the w a ypoint number you selected on the first page. Saving Cur sor P osition as a W aypoint (Select Number Method) T o save the cursor position under a specific ...
-
Eagle Electronics Eagle View - page 31
27 W A YPOINT NAMES It automatically assigns the wa ypoint number as a name when the w a ypoint position is sav ed. Y ou can find a wa y- point by highlighting the “Name” label on the wa ypoint menu as shown at right. Now press the right or left arrow k eys to scroll through the sa v ed wa ypoints. Only w aypoints that ha ve a position will sho ...
-
Eagle Electronics Eagle View - page 32
28 shown at right. Press the down arrow k ey , then press the right arrow ke y until the desired wa ypoint number shows in the bo x. When ev er ything on this page is correct, press the ENT ke y . Note:The names in the “F rom” and “T o” bo xes are not the wa ypoint numbers - they are the w aypoint names . When a w aypoint is mo ved from one ...
-
Eagle Electronics Eagle View - page 33
29 Delete a W a ypoint T o erase all of the inf or mation in a wa ypoint, simply press the WPT k ey , then select the wa ypoint you w ant to delete. Now highlight the “Wpt-Op- tions” label and press the r ight arro w key . Finally , highlight the “Delete WPT” label and press the right arrow ke y . A message appears, asking if you really w a ...
-
Eagle Electronics Eagle View - page 34
30 ROUTES Y ou can connect sev eral user wa ypoints together to f or m a route . When you recall the route , the Eagle View will sho w y ou navigation inf ormation to the first wa ypoint in the route, then when you reach that wa ypoint, it switches to the ne xt wa ypoint, and so on until you reach the last wa ypoint in the route. T o create a route ...
-
Eagle Electronics Eagle View - page 35
31 This menu lets y ou go to the waypoint selection menu, delete a wa ypoint from the route, or see details about any w a y- point in the route. Since we want to add a wa ypoint to the route, press the right arrow k ey on the “Inser t F rom WPTS” label. The screen shown below appears . Select W aypoints Select the first wa ypoint either by usin ...
-
Eagle Electronics Eagle View - page 36
32 Finishing the Route When you’v e selected all of the wa ypoints f or the route , simply press the EXIT k ey until you return to the navigation, plotter , or windows screen. Y our route is sa v ed in memory . Delete a W a ypoint T o delete a wa ypoint from a route, first select the route from the “Route Plan- ning” or “Run Route” menus, ...
-
Eagle Electronics Eagle View - page 37
33 The b lack bo x is on the “Route # 1” label. If this isn’t the route you w ant to use, press the right or left arrow ke ys to switch to another one . Bef ore star ting the route, y ou’ll need to decide if you want to start at the begin- ning and tra vel f orward or star t at the last w aypoint in the route and tra vel backw ards (rev ers ...
-
Eagle Electronics Eagle View - page 38
34 Skip W aypoint The Eagle Vie w lets you skip a wa ypoint in a route without stopping the route. T o do this, first press the MENU k ey , then highlight the “Routes” menu and press the right arrow k ey , then highlight the “Skip WPT” label and press the right ar- row k ey . The unit retur ns to the naviga- tion, plotter , or windows scree ...
-
Eagle Electronics Eagle View - page 39
35 Navigating to a cur sor location The Eagle Vie w lets y ou na vigation to a location without storing it in the waypoint database by using the plotter and cur- sor . T o do this, first s witch to the plotter screen. Now move the cursor to the lo- cation that you w ant to navigate to . Next, press the MENU ke y . A new men u ap- pears on the list: ...
-
Eagle Electronics Eagle View - page 40
36 Navigating to a W aypoint using the Plotter The unique “birds-eye” view used b y the plotter gives y ou an easy wa y to na vi- gate to a w a ypoint. On the screen shown at right, the diamond with a cross in it is your present position. The box with the “S” in it w as your starting location when you recalled the w a ypoint. The dotted lin ...
-
Eagle Electronics Eagle View - page 41
37 SYSTEM SETUP The Eagle View has se ver al menus and commands listed under the “System Setup” label on the main menu. These commands aff ect the basic operation of the unit. T o use them, press the MENU ke y , then highlight the “System Setup” label. Press the right arrow k ey . The screen shown at right appears. SPEAKER Y ou can turn the ...
-
Eagle Electronics Eagle View - page 42
38 T o change a unit of measure, first select the “Set Units” from the “System Setup” menu. The screen shown at right ap- pears. Highlight the desired selection, then press the left or right arrow ke y . Y ou can change one or all of the settings on this page. When y ou’ re finished, press the EXIT ke y . P osition Format T o change the p ...
-
Eagle Electronics Eagle View - page 43
39 NMEA / DGPS The Eagle View transmits data through the data port in the back of the unit using NMEA 0183 f or mat, v ersion 1.5 or 2.0. This data is used by other electronic de vices such as mar ine autopilots f or position and steer- ing inf or mation. DGPS on the other hand, is a data input. DGPS is an acronym for Diff er- ential Global P ositi ...
-
Eagle Electronics Eagle View - page 44
40 All wiring connections to the Eagle View are made to it’ s power cab le. See the sample wiring diagrams on the ne xt page for general wiring proce- dures. Read your other product’ s owner’ s manual f or more wir ing inf or ma- tion. Once the cables are wired, turn the Eagle View on, press the menu k ey , and select NMEA / DGPS from the Sys ...
-
Eagle Electronics Eagle View - page 45
41 T O EAGLE VIEW O THER DEVICE 12 VDC BA TTERY BLACK WIRE GROUND WIRES WHITE WIRE RED WIRE T O +12V OTHER DEVICE’S RECEIVE DA T A WIRE EAGLE VIEW’S WIRES OTHER DEVICE’S WIRES EA GLE VIEW TRANSMIT - TING NMEA D A T A TO ANO THER DEVICE TO EA GLE VIEW DGPS RECEIVER 12 VDC BA TTERY BLACK WIRE GROUND WIRES WHITE WIRE RED WIRE T O +12V DGPS RECEI ...
-
Eagle Electronics Eagle View - page 46
42 the e xception of ser ial communications , typically no other setup needs to be made with these receivers . If you ha ve any other Magna vo x or Starlink compatible DGPS receiv er con- nected to the Eagle View , you ma y need to change the settings. T o do this, mov e the blac k box to the “Configure DGPS Beacon Receiv er” label and press th ...
-
Eagle Electronics Eagle View - page 47
43 If you restore the unit to the f actor y settings , all options such as contrast, alarms, and other system choices are retur ned to their def ault values . How e v er , no waypoints , routes , or icons are erased. RESET GROUPS T o retur n all groups to their f actor y def aults, highlight the “RESET GROUPS” label on the “System Setup” me ...
-
Eagle Electronics Eagle View - page 48
44 the receiv er. F or e xample, if you entered east longitude instead of west. Or if you’v e mov ed a long distance with the unit turned off. T o send a cold star t message to the re- ceiv er , highlight the “Ex ecute GPS Cold Star t” label, then press the right arrow ke y . A message appears, asking y ou if you really w ant to do a cold sta ...
-
Eagle Electronics Eagle View - page 49
45 PCF (P osition Correction F actor) Another method used to make y our display match a chart or map is called “PCF” or P osition Correction F actor . This unit gives y ou the capability to mov e or offset the position shown on the displa y to match one on the char t. The unit will add this offset to all position and navigation displa ys at all ...
-
Eagle Electronics Eagle View - page 50
46 After you’v e entered the latitude/longitude correction, press the ENT ke y to accept it. The Eagle View erases the PCF entry screen and retur ns to the na vigation or mapping screens with the correction f actor applied. POSITION PINING When using a GPS receiver at e xtremely low speeds, it can ha ve troub le determining your course ov er grou ...
-
Eagle Electronics Eagle View - page 51
47 T o use any of these alar ms , first press the MENU ke y , then select the “ALARMS/CDI” menu. A screen similar to the one shown at right appears. Press the up or down arrow k ey to mov e the blac k box to the desired alarm, then press the right arrow ke y to turn it on. T o adjust an alar m’ s distance, mo v e the blac k box to the alarm? ...
-
Eagle Electronics Eagle View - page 52
48 SIMULA TOR A simulator is built into the Eagle View that has se ve ral options. Y ou can use nearly all of the unit’ s f eatures - ev en sav e and recall wa ypoints. This is useful f or trip planning. T o use the simulator , press the MENU ke y , then press the up or down arrow ke ys until the “Simulator Setup” menu is surrounded by the b ...
-
Eagle Electronics Eagle View - page 53
49 to increase or decrease the speed. Use the right and left arrow ke ys to change the trac k. Press the EXIT ke y to erase these men us . When you’ re finished changing the trac k and speed, press the EXIT key to erase the menus . T o tur n the simulator off , press the MENU key , then mov e the blac k bo x to the “Simulator Setup” label. Fi ...
-
Eagle Electronics Eagle View - page 54
50 WINDO WS The f ollo wing is a listing of windows g roups A through O . GROUP “A” GROUP “B” GROUP “C” GROUP “D” GROUP “E” GROUP “F” GROUP “G” GROUP “ H” ...
-
Eagle Electronics Eagle View - page 55
51 GROUP “I” GROUP “J” GROUP “K” GROUP “L ” GROUP “M” GROUP “ N ” GROUP “O” ...
-
Eagle Electronics Eagle View - page 56
52 Eagle's UPS Return Service - U.S.A. Only Eagle Electronics and United Parcel Service (UPS) are proud to offer all of our customers free shipping for all units sent to us f or repair or ser vice . If you hav e to send this unit to the factory , and y ou are in the continental United States, use the enclosed UPS shipping label f or easy , fre ...
-
Eagle Electronics Eagle View - page 57
53 KEEP THIS LABEL! Y OU WILL NEED IT IF Y OU EVER NEED T O RETURN Y OUR UNIT T O THE F A CT OR Y FOR REP AIR. Accessory Ordering Information T o order accessor ies such as pow er cab les, please contact: 1) Y our local marine dealer. Most quality dealers that handle mar ine elec- tronic equipment should be able to assist y ou with these items. Con ...
-
Eagle Electronics Eagle View - page 58
54 EA GLE ELECTRONICS FULL ONE-YEAR W ARRANTY “We", “our”, or “us” refers to EA GLE ELECTR ONICS , a division of LEI, the manuf acturer of this product. “Y ou” or “your” ref ers to the first person who purchases this product as a consumer item for personal, f amily , or household use. We warr ant this product against defects ...
-
Eagle Electronics Eagle View - page 59
55 ANTENNA MODULE TEMPLA TE 25MM (1”) (If Necessary) 4.75MM (3/16”) 4 PLA CES ...
-
Eagle Electronics Eagle View - page 60
56 THIS P AGE INTENTIONALL Y LEFT BLANK ...
-
Eagle Electronics Eagle View - page 61
57 How to Obtain Service (Canadian Customers Only) We bac k your investment in quality products with quic k, expert ser vice and gen uine Eagle replacement par ts. If you need service or repairs, contact the Eagle F actor y Customer Service Depar tment at the toll-free number listed below . A technician may be able to solv e the problem and sav e y ...
-
Eagle Electronics Eagle View - page 62
58 How to Obtain Service - U .S.A. Only We bac k your inv estment in quality products with quick, e xper t ser vice and genuine Eagle™ replacement par ts . If you're in the United States and you ha ve questions, please contact the F actor y Customer Ser vice Depar tment using our toll-free n umber listed below . Y ou must send the unit to th ...
Do you have a question concerning Eagle Electronics Eagle View?
Use the form below
If you did not solve your problem by using a manual Eagle Electronics Eagle View, ask a question using the form below. If a user had a similar problem with Eagle Electronics Eagle View it is likely that he will want to share the way to solve it.