English dropdown-ico

Manual Stanley Black & Decker HD01

20 pages 2.58 mb
Download

Go to site of 20

Summary
  • Stanley Black & Decker HD01 - page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 72659 2/2015 V er . 6 USER MANUAL Safety , Operation and Maintenance HD01 Hydraulic Hammer Drill ...

  • Stanley Black & Decker HD01 - page 2

    2 ► HD01 User Manual DECLARATION OF CONF ORM ITY ÜBEREINSTIMM UNGS - ERKLARUNG DECLARATION DE CONF ORMITE CEE DECLARACION DE CONFO RMIDAD DICHIARAZIONE DI CONFO RMITA Hydraulic Tools _______ _________ ___________ ___________ _________ ___________ _________ ___ I, the undersigned: Ich, der Unterzeichnende: Je soussi gné: El abajo firmante: lo so ...

  • Stanley Black & Decker HD01 - page 3

    HD01 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer . Please read the following warning. For the nearest authorized and certie ...

  • Stanley Black & Decker HD01 - page 4

    4 ► HD01 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and signal words, as shown below , are used to emphas ...

  • Stanley Black & Decker HD01 - page 5

    HD01 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs. ...

  • Stanley Black & Decker HD01 - page 6

    6 ► HD01 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL. T AG TO BE REMOVED ONL Y BY TOOL OPERA TOR. SEE OTHER SIDE 1. F AILURE TO USE ...

  • Stanley Black & Decker HD01 - page 7

    HD01 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermoplastic ...

  • Stanley Black & Decker HD01 - page 8

    8 ► HD01 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT ORS 4-6 1 ...

  • Stanley Black & Decker HD01 - page 9

    HD01 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max. uid tempe ...

  • Stanley Black & Decker HD01 - page 10

    10 ► HD01 User Manual PRE-OPERA TION PROCEDURES CHECK POWER SOURCE 1. Using a calibrated owmeter and pressure gauge, check that the hydraulic power source develops a ow of 4–9 gpm/15–34 lpm at 950–2000 psi/65–140 bar . 2. Make certain that the hydraulic power source is equipped with a relief valve set to open at 2100– 2250 psi/145 ...

  • Stanley Black & Decker HD01 - page 11

    HD01 User Manual ◄ 1 1 MODE SELECTOR (FIG 2) Drill only mode: T o use drill-only mode, press mode selector button (B) g-2 and turn the mode selec - tor (A) so the yellow arrow points to the corresponding symbol. Use drill-only mode for screwdriving and for drilling into metal, wood and plastics. Hammer only mode: For light chiseling and demoli ...

  • Stanley Black & Decker HD01 - page 12

    12 ► HD01 User Manual SIDE HANDLE The side handle assembly , including the depth gauge, ts over the front housing of the hammer drill to assist the operator in maneuvering the tool. T o adjust the side handle to a comfortable position, twist the hand grip in a counterclockwise direction and reposi- tion the handle assembly . Once in position, ...

  • Stanley Black & Decker HD01 - page 13

    HD01 User Manual ◄ 13 T ighten further by applying the chuck key successively to all three guide holes of the chuck. The chuck key must not be attached to the tool with a chain, cord, or similar means. When drilling into small work pieces, secure the piece (by clamping in a vise or otherwise securing it to the work sur- face) so that the piece is ...

  • Stanley Black & Decker HD01 - page 14

    14 ► HD01 User Manual This tool is furnished with an on-off valve spool commonly referred to as a “dual spool” which permits adjustment so the tool may be operated on either an open-center hydraulic system or a closed-center hydraulic system. The dual spool is normally set to the open-center (OC) position at time of manufac- ture. The dual sp ...

  • Stanley Black & Decker HD01 - page 15

    HD01 User Manual ◄ 15 PROBLEM CAUSE SOLUTION Drill will not start Power not being supplied. Check to make certain that both hoses are connected. T urn hydraulic circuit control valve ON. Defective quick-disconnect. Check each disconnect separately . Replace as necessary . Jammed motor and/or parts. Separate modules and inspect. See Service manual ...

  • Stanley Black & Decker HD01 - page 16

    16 ► HD01 User Manual PROBLEM CAUSE SOLUTION Drill operates in only one direction. Forward or reverse. Reverse spool incorrectly installed. Do not separate modules. Reassemble. See Service section. Reverse spool faulty . Do not separate modules. Replace reverse spool. See Service section. T ool hose ow is reversed. T ool must not be reversed b ...

  • Stanley Black & Decker HD01 - page 17

    HD01 User Manual ◄ 17 Rotation Speed at 6 gpm ................................................................................................................................ 800 rpm Blows per Minute at 6 gpm ........................................................................................................................ 4200 blows Weight ...

  • Stanley Black & Decker HD01 - page 18

    18 ► HD01 User Manual 1 2 3 4 5 6 8 9 10 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 43 45 47 48 50 51 52 53 56 57 58 60 62 64 65 6 19 14 46 16 16 42 61 65 59 66 64 63 HD01 P ARTS ILLUSTRA TION ...

  • Stanley Black & Decker HD01 - page 19

    HD01 User Manual ◄ 19 ITEM P/N QTY DESCRIPTION 1 00106 1 * O-RING 3/8 X 1/2 X 1/16 -012 2 001 12 1 * QUAD RING 1/4 X 3/8 X 1/16 -010 3 00179 1 MOT OR SEAL W ASHER 4 00289 2 DOWEL PIN 3/16 X 3/4 LG. 5 00621 1 * O-RING 1-1/4 X 1-3/8 X 1/16 -026 6 00779 7 HSHCS 8-32 X 1.000 7 00783 7 PIPE PLUG (NOT PICTURED) P ART OF ITEM 57 8 00936 2 ADAPTER -8 (1/ ...

  • Stanley Black & Decker HD01 - page 20

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com ...

Manufacturer Stanley Black & Decker Category Cordless Drill

Documents that we receive from a manufacturer of a Stanley Black & Decker HD01 can be divided into several groups. They are, among others:
- Stanley Black & Decker technical drawings
- HD01 manuals
- Stanley Black & Decker product data sheets
- information booklets
- or energy labels Stanley Black & Decker HD01
All of them are important, but the most important information from the point of view of use of the device are in the user manual Stanley Black & Decker HD01.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Stanley Black & Decker HD01, service manual, brief instructions and user manuals Stanley Black & Decker HD01. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Stanley Black & Decker HD01.

Similar manuals

A complete manual for the device Stanley Black & Decker HD01, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Stanley Black & Decker HD01 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Stanley Black & Decker HD01.

A complete Stanley Black & Decker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Stanley Black & Decker HD01 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Stanley Black & Decker HD01, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Stanley Black & Decker HD01, that we can find in the current document
3. Tips how to use the basic functions of the device Stanley Black & Decker HD01 - which should help us in our first steps of using Stanley Black & Decker HD01
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Stanley Black & Decker HD01
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Stanley Black & Decker HD01 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Stanley Black & Decker HD01?

Use the form below

If you did not solve your problem by using a manual Stanley Black & Decker HD01, ask a question using the form below. If a user had a similar problem with Stanley Black & Decker HD01 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)