-
Zenoah EHT753D - page 1
eHT753S eHT603D 848-D3N-93A1 (704) OWNER’S MANUAL HEDGE-TRIMMERS • Before using our products, please read this manual carefully to understand the proper use of your unit. • Keep this manual handy. CA UTION ...
-
Zenoah EHT753D - page 2
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ NOTES ON TYPES OF WARNINGS IN THE MANUAL Thi ...
-
Zenoah EHT753D - page 3
1. Plate receive 2. Right handle 3. Starter 4. Fuel cap 5. Left handle 6. Engine Stop switch 7. Throttle lever 8. Fuel tank 9. Muffler 10. Blade 11. Air cleaner 12. Spark plug 13. Gear case 14. Throttle cable 15. Choke lever 16. Front handle 17. Engine switch 18. Safty lock lever 19. Rear handle 20. Lock lever 21. Grease nipple English 1. PARTS LOC ...
-
Zenoah EHT753D - page 4
English For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake. (a). The port to refuel the "MIX GASOLINE" POSITION: FUEL TANK CAP (b).The direction to close the choke POSITION: AIR CLEANER COVER (c). The direction to open the choke POSITION: ...
-
Zenoah EHT753D - page 5
3. SAFETY PRECAUTIONS ■ BEFORE USING THE MACHINE a. Read this owner's manual carefully to understand how to operate this unit properly. b. This product has been designed for use in trimming leaves and branches from trees and hedges, and it should never be used for any other purpose since doing so could result in unforeseen accidents and inju ...
-
Zenoah EHT753D - page 6
3. SAFETY PRECAUTIONS g. Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn leads to accidents and injury. Limit the amount of time over which the hedge-trimmer is to be used continuously to somewhere around 30~40 minutes per session, and take 10~20 minutes of rest between work sessions. Also try to ...
-
Zenoah EHT753D - page 7
3. SAFETY PRECAUTIONS ■ WARNING CONSIDERING HANDLING OF FUEL a. The engine of this product is designed to run on a mixed fuel which contains highly flammable gasoline. You should never store cans of fuel or refill the fuel tank in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat o ...
-
Zenoah EHT753D - page 8
3. SAFETY PRECAUTIONS persons, always check the presence and locations of others so as to maintain a distance each person sufficient to ensure safety. c. Make sure that there are no loose screws or bolts, fuel leaks, ruptures, dents, or any other problems which might interfere with safe operation. Be especially careful to check that there is nothin ...
-
Zenoah EHT753D - page 9
3. SAFETY PRECAUTIONS ■ KICKBACK SAFETY PRECAUTIONS •A dangerous reaction may occur when the spinning blade contacts a solid object in the critical area. It is called Kick back. As a result, the operator can lose control of the unit which can cause serious or fatal injury. Avoid kickback, observe the safety precautions below strictly. 1. Keep t ...
-
Zenoah EHT753D - page 10
3. SAFETY PRECAUTIONS d. If the grass gets caught in the blade during operation, or if you need to check the unit or refuel the tank, always be sure to turn off the engine. e. If the blade touches a hard object like a stone, immediately stop the engine and check if something is wrong with the blade. If so, replace the blade by new one. f. If someon ...
-
Zenoah EHT753D - page 11
English d. When sharpening, removing, or reattaching the blade, be sure to wear thick, sturdy gloves and use only proper tools and equipment to prevent injury. e. When replacing blade or any other parts or when replacing the oil or any lubricants, always be sure to use only ZENOAH products or products which have been certified by ZENOAH for use wit ...
-
Zenoah EHT753D - page 12
English 4. FUEL •G asoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. • Wipe up all spills before starting the engine. •M ake sure to stop the engine and allow it cool before refueling the unit. • Keep open flames away from the area where fuel is handled or stored. •N ever use oil for 4 cycle engine use or ...
-
Zenoah EHT753D - page 13
English 5. OPERATION ■ STARTING THE ENGINE Keep the blades clear of everything around It as they will start moving upon the engine starts. 1. [eHT753S] Make sure that the throttle lever is at idling position. [eHT603D] Release the throttle lever and make sure it is fully back. (F1) 2. [eHT603D] Set the engine switch to the “I (RUN)” position. ...
-
Zenoah EHT753D - page 14
English ■ CUTTING WORK •W eather conditions and altitude may effect carburation. • Do not allow anyone to stay close to the hedge-trimmer while working or while adjusting the carburetor. ■ HOW TO USE HANDLE [eHT603D only] (F5) To reduce fatigue when trimming hedges, the handle can be swivelled through 90° to the left or right. Do not press ...
-
Zenoah EHT753D - page 15
English 6. MAINTENANCE F8 F10 F9 Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool. ■ BLADE (F8) • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file. Point: 1. Keep the end corner sharp. 2. Round the root of the edge. ...
-
Zenoah EHT753D - page 16
16 English 6. MAINTENANCE F11 F12 3. Check if the safety lock returns to its original position when you release your hand from safety lock. If you find any defects at the checks above, contact your nearest servicing dealer for repair. ■ ANTI-VIBRATION SYSTEM (F11) The deformed or damaged anti- vibration system may cause of the breakages like gett ...
-
Zenoah EHT753D - page 17
17 English 6. MAINTENANCE F13 F14 F15 ■ FUEL FILTER (F13) When the engine runs short of fuel supply, check the fuel strainer for blockage. ■ WAY OF THE COOLING AIR (F14) This engine is air-cooled. Dust clogging between the inlet port of the cooling air and cylinder fins will cause overheating of the engine. Periodically check and clean the cyli ...
-
Zenoah EHT753D - page 18
18 English 6. MAINTENANCE F16 F17 F18 ■ GEARCASE (F16) Supply multi-purpose grease at every 20 hours of use . 1. Use a grease pump. 2. Feed grease until it comes out of the base of blades.(F16-a) ■ ADJUSTING CARBURETOR (F17) The carburetor has been adjusted at the factory. Should your unit need readjustment due to the changes in altitude or ope ...
-
Zenoah EHT753D - page 19
19 English 6. MAINTENANCE F19 F20 ■ MUFFLER AFTER 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent at the same time. (F19) (1) screw driver (2) muffler 2. Tighten all screws, bolts, and fittings. 3. Check to see if any oil or grea ...
-
Zenoah EHT753D - page 20
English Model name .................. eHT753S [eHT603D] Type .......Single blade [Double-blade], double-action type Blade length .............................. 750 [600]mm Engine model ........................... Zenoah G20LH Displacement ......................................... 21.7cc Carburetor .......................... Diaphragm type Ignition ...
У вас вопрос, касающийся Zenoah EHT753D?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Zenoah EHT753D, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Zenoah EHT753D со всей вероятностью он захочет поделиться методом ее решения.