-
Harbor Freight Tools 96526 - page 1
19.2V 1/2”CORDLESS DRILL/DRIVER Model 96526 SET -UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visi ...
-
Harbor Freight Tools 96526 - page 2
Page 2 SKU 96526 For technical questions, please call 1-800-444-3353. SA VE THIS MANUAL Keep this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has ...
-
Harbor Freight Tools 96526 - page 3
Page 3 SKU 96526 For technical questions, please call 1-800-444-3353. GENERAL SAFETY RULES W ARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock, re, and/or serious injury . The term “power tool” in all of the warnings listed below refers to your line-operated (corded) power tool or batt ...
-
Harbor Freight Tools 96526 - page 4
Page 4 SKU 96526 For technical questions, please call 1-800-444-3353. Avoid accidental starting. Ensure the switch is in the of f-position before plugging in. Carrying power tools with your nger on the switch or plugging in power tools that have the switch on invites accidents. Remove any adjusting key or wrench before turning the power tool on. ...
-
Harbor Freight Tools 96526 - page 5
Page 5 SKU 96526 For technical questions, please call 1-800-444-3353. Service Have your power tool serviced by a qualied technician using only identical replacement parts. This will ensure that the safety of the power tool is maintained . SPECIFIC SAFETY RULES Maintain labels and nameplates on the tool. These carry important safety information. ...
-
Harbor Freight Tools 96526 - page 6
Page 6 SKU 96526 For technical questions, please call 1-800-444-3353. • Any power cord must be properly grounded. Ground Fault Circuit Interrupter (GFCI) should also be implemented – it prevents sustained electrical shock. T o reduce the risk of personal injury where the drill bit may contact hidden wiring, hold the tool by its plastic insulate ...
-
Harbor Freight Tools 96526 - page 7
Page 7 SKU 96526 For technical questions, please call 1-800-444-3353. the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user , reducing the risk of electric shock. (See 3-Prong Plug and Outlet.) The grounding prong in the plug is connected through the green wire insid ...
-
Harbor Freight Tools 96526 - page 8
Page 8 SKU 96526 For technical questions, please call 1-800-444-3353. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See T able A.) If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the requir ...
-
Harbor Freight Tools 96526 - page 9
Page 9 SKU 96526 For technical questions, please call 1-800-444-3353. SPECIFICA TIONS Electrical Requirements Charger Input: 120 V~ / 60 Hz Charger Output: 24 VDC / 400mA Battery T ype: 1300 mAh Ni-Cd Rechargeable Charge T ime: 3 to 5 Hours Power Cord T ype: 22 AWG x 2C Drill Speed Dual Speed Drill RPM: 0~400 RPM (#1 Setting) / 0~1050 RPM (#2 Setti ...
-
Harbor Freight Tools 96526 - page 10
Page 10 SKU 96526 For technical questions, please call 1-800-444-3353. Insert the Battery (29) into the Charger Stand (23). (See Figure A.) The Battery (29) will charge in approximately 3 to 5 hours. Do not charge the Battery for longer than 5 hours. Subsequent charges will also take between 3 and 5 hours. Allow the Charger Stand (23) to cool down ...
-
Harbor Freight Tools 96526 - page 11
Page 1 1 SKU 96526 For technical questions, please call 1-800-444-3353. T o Insert And Remove Drill And Screw Driver Bits Set the Forward/Reverse Switch (7) to the “LOCKED” (center) position. (See Figure C.) FORW ARD/REVERSE SWITCH (7) POWER SWITCH (10) The Drill/Driver is equipped with a Keyless Chuck (1). T o insert and remove drill bits or s ...
-
Harbor Freight Tools 96526 - page 12
Page 12 SKU 96526 For technical questions, please call 1-800-444-3353. Hold the Keyless Chuck (1) rmly while turning the forward section of the Chuck counterclockwise. This opens the Chuck to accept the drill or screw driver bit. (See Figure D.) Continue turning the Keyless Chuck (1) counterclockwise until the drill bit or screw driver slips int ...
-
Harbor Freight Tools 96526 - page 13
Page 13 SKU 96526 For technical questions, please call 1-800-444-3353. A higher setting equals more torque; therefore, position #1 (low torque) is appropriate for driving screws into wood without stripping the screw , but would not provide enough torque for drilling or driving into harder materials. (See Figure E.) Position #20 is indicated by a dr ...
-
Harbor Freight Tools 96526 - page 14
Page 14 SKU 96526 For technical questions, please call 1-800-444-3353. The Drill/Driver has a variable speed for drilling. T o vary the speed of the drilling action, vary the pressure on the Power Switch (10). Drill only as deep as is necessary . Do not drill deeper than necessary into walls or other areas where you cannot identify any possible haz ...
-
Harbor Freight Tools 96526 - page 15
Page 15 SKU 96526 For technical questions, please call 1-800-444-3353. faster the Battery loses power . A Battery that gets too hot can be permanently damaged. Never over-discharge a Battery by using the tool even after tool performance is decreasing. Never attempt to discharge a tool’s Battery by continuing to pull the tool’s Power Switch. Whe ...
-
Harbor Freight Tools 96526 - page 16
Page 16 SKU 96526 For technical questions, please call 1-800-444-3353. PLEASE READ THE FOLLOWING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE P AR TS LIST AND ASSEMBL Y DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONL Y . NEITHER THE MANUF ACTURER OR DISTRIBUTOR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND T O THE BUYER THA ...
-
Harbor Freight Tools 96526 - page 17
Page 17 SKU 96526 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIAGRAM CARRYING CASE (36) NOT SHOWN. ...
-
Harbor Freight Tools 96526 - page 18
Page 18 SKU 96526 For technical questions, please call 1-800-444-3353. Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only , and are not avail- able individually as replacement parts. LIMITED 90 DA Y W ARRANTY ...
У вас вопрос, касающийся Harbor Freight Tools 96526?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Harbor Freight Tools 96526, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Harbor Freight Tools 96526 со всей вероятностью он захочет поделиться методом ее решения.