-
HP (Hewlett-Packard) FSPCI64S - page 1
FuturePlus Systems Corporation LOCAL BUS PCI Scope Preprocessor Users Manual-FSPCI64S For Hewlett-Packard Logic Analysis Systems Revision 1.0 FuturePlus Systems and PCI Scope is a trademark of FuturePlus Systems Corporation Copyright 1995 FuturePlus Systems Corporation ...
-
HP (Hewlett-Packard) FSPCI64S - page 2
2 HOW TO REACH US 4 PRODUCT WARRANTY 5 Limitation of warranty 5 Exclusive Remedies 5 Assistance 6 INTRODUCTION 7 How to Use This Manual 7 ANALYZING THE PCI LOCAL BUS 8 Duplicating the Master Diskette 8 Accessories Supplied 8 Minimum Equipment Required 8 Signal Naming Conventions 9 Connecting the 208 pin MultiProbe Pod to the PCI Scope Preprocessor ...
-
HP (Hewlett-Packard) FSPCI64S - page 3
3 Standards Supported 15 Power Requirements 15 MultiProbe Pods required 15 Signal loading 15 Operations 16 Environmental Temperature 16 Altitude 16 Humidity 16 Testing and Troubleshooting 16 Servicing 16 Signal Connections for the MultiProbe POD 17 ...
-
HP (Hewlett-Packard) FSPCI64S - page 4
4 How to reach us FuturePlus Systems can be reached at: FuturePlus Systems Corporation 36 Olde English Road Bedford, NH 03110 TEL:603-471-2734 FAX:603-471-2738 Internet: 71035.3052@compuserve.com WEB:www.futureplus.com FuturePlus Systems is represented in Japan by: ANDOR Systems Support Co.,LTD. 15-8, Minami-Shinagawa, 2-chome, Shinagawa-ku Tokyo 1 ...
-
HP (Hewlett-Packard) FSPCI64S - page 5
5 Product Warrant y This FuturePlus Systems product has a warranty against defects in material and workmanship for a period of 1 year from the date of shipment. During the warranty period, FuturePlus Systems will, at its option, either replace or repair products proven to be defective. For warranty service or repair, this product must be returned t ...
-
HP (Hewlett-Packard) FSPCI64S - page 6
6 SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY. Product maintenance agreements and other customer assistance agreements are available for FuturePlus Systems products. For assistance, contact the factory. Assistance ...
-
HP (Hewlett-Packard) FSPCI64S - page 7
7 Introduction The PCI Scope Preprocessor module provides a complete interface between any PCI add-in slot and the HP MultiProbe system. The Preprocessor interface connects the signals from the PCI Local bus to the inputs of a 208 PQFP package used as the MultiProbe connection point. The PCI Scope Preprocessor is a passive bus monitor which does no ...
-
HP (Hewlett-Packard) FSPCI64S - page 8
8 Analyzing the PCI Local Bus This chapter introduces you to the PCI Scope Preprocessor and lists the minimum equipment required and accessories supplied for PCI Local Bus analysis. Before you use the PCI Preprocessor software, make a duplicate copy of the master diskette. Then store the master diskette and use the back-up copy to configure your lo ...
-
HP (Hewlett-Packard) FSPCI64S - page 9
9 • An Oscilloscope • The PCI Scope Preprocessor Product • A PCI target bus This operating manual uses the same signal notation as the PCI LOCAL BUS SPECIFICATION - REVISION 2.1. That is, a # symbol at the end of a signal name indicates that the signal’s active state occurs when it is at a low voltage. The absence of a # symbol indicates th ...
-
HP (Hewlett-Packard) FSPCI64S - page 10
10 PCI_MUL.DUT and PCI.ADP from your PCI Scope Preprocessor diskette to that directory. 3. Access the configuration menu of the MultiProbe Control card. 4. Select POD setup for the POD that will be connected to the Scope Preprocessor. 5. On the next menu select #2 Specify POD adapter and then select the file PCI.ADP and select proceed . 6. Return t ...
-
HP (Hewlett-Packard) FSPCI64S - page 11
11 Analog Analysis Since the PCI Scope Preprocessor interface contains only passive matching terminators it introduces negligible skew to the PCI Local Bus signals. The following procedure describes the major steps required to perform analog analysis measurements with the PCI Scope Preprocessor module. 1. Install the PCI Scope Preprocessor module i ...
-
HP (Hewlett-Packard) FSPCI64S - page 12
12 Select the oscilloscope for each MultiProbe output using the Select Signals menu of the MultiProbe control module. 1. Access the Select Signals menu. 2. Select the scope for each output a) Choose the output (Output 1 or Output 2) of the control module that is connected to the pod that is attached to the PCI Scope Preprocessor. In the Select Sign ...
-
HP (Hewlett-Packard) FSPCI64S - page 13
13 Using an HP16534A oscilloscope If you are using an HP 16534A oscilloscope, then follow this procedure. 1. Access the oscilloscope menus. To view your measurements with an HP16534A oscilloscope, you need to exit the MultiProbe Control menus, then enter the oscilloscope menus. Select the MultiProbe field, then select the oscilloscope module. 2. Us ...
-
HP (Hewlett-Packard) FSPCI64S - page 14
14 When the PCI Personality Adapter 101 is not in use, keep it in its original container. The file PCI.ADP matches the configuration of the PCI Personality Adapter and configures the MultiProbe for PCI Analysis. If you wish to configure your own Personality adapter follow the instructions for Programming the ground connections in your 208 MultiProb ...
-
HP (Hewlett-Packard) FSPCI64S - page 15
15 General Information This chapter provides additional reference information including the characteristics and signal connections for the PCI Scope Preprocessor module. The following operating characteristics are not specifications, but are typical operating characteristics for the PCI Scope Preprocessor module. 32/64 bit PCI Local bus accepting t ...
-
HP (Hewlett-Packard) FSPCI64S - page 16
16 information on the electrical loading of the MultiProbe Pod refer to your Hewlett-Packard MultiProbe specification. All PCI Local Bus operations supported. Operating:0 to 55 degrees C (+32 to +131 degrees F) Non operating:-40 to +75 degrees C (-40 to +167 degrees F) Operating: 4,6000m (15,000 ft) Non operating: 15,3000m (50,000 ft) Up to 90% non ...
-
HP (Hewlett-Packard) FSPCI64S - page 17
17 The below table shows the connection from the PCI Local Bus to the PQFP package that acts as the MultiProbe Contact point. If the pin is not listed it is Grounded. PCI Signal PQFP pin AD50 1 AD51 3 AD52 5 AD53 7 AD54 9 AD55 11 AD56 13 AD57 15 AD58 17 AD59 19 AD60 21 AD61 23 AD62 25 AD63 27 INTA# 53 INTB# 55 INTC# 57 INTD# 59 RST# 61 CLK 63 AD31 ...
-
HP (Hewlett-Packard) FSPCI64S - page 18
18 AD26 75 AD25 77 AD24 79 C/BE3# 81 AD23 83 AD22 85 AD21 87 AD20 89 AD19 91 AD18 93 AD17 95 AD16 97 C/BE2# 99 FRAME# 101 IRDY# 103 TRDY# 105 DEVSEL# 107 STOP# 109 LOCK# 111 SDONE 113 PERR# 115 SBO# 117 SERR# 119 PAR 121 C/BE1# 123 AD15 125 AD14 127 AD13 129 AD12 131 AD11 133 AD10 135 ...
-
HP (Hewlett-Packard) FSPCI64S - page 19
19 AD09 137 C/BE0# 139 AD08 141 AD07 143 AD06 145 AD05 147 AD04 149 AD03 151 AD02 153 AD01 155 AD00 157 ACK64# 159 REQ64# 161 C/BE7# 163 C/BE6# 165 C/BE5# 167 C/BE4# 169 PAR64 171 AD32 173 AD33 175 AD34 177 AD35 179 AD36 181 AD37 183 AD38 185 AD39 187 AD40 189 AD41 191 AD42 193 AD43 195 AD44 197 ...
-
HP (Hewlett-Packard) FSPCI64S - page 20
20 AD45 199 AD46 201 AD47 203 AD48 205 AD49 207 ...
У вас вопрос, касающийся HP (Hewlett-Packard) FSPCI64S?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с HP (Hewlett-Packard) FSPCI64S, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с HP (Hewlett-Packard) FSPCI64S со всей вероятностью он захочет поделиться методом ее решения.