-
Patton electronic 1052 - page 1
USER MANUAL MODEL 1052 iDSL Modem with RS-232 Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P a r t# 07M1052- B Doc# 058061 U B Revised 5/24/02 An ISO-9001 Certified Company ...
-
Patton electronic 1052 - page 2
2 T ABLE OF CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 FCC Information ........................................................................... 4 1.2 CE Notice ...................................................................................... 4 1.3 Service ....................... ...
-
Patton electronic 1052 - page 3
3 A.10 Temperature Range .................................................................... 17 A.11 Altitude ........................................................................................ 17 A.12 Humidity ...................................................................................... 17 A.13 Weight ............................... ...
-
Patton electronic 1052 - page 4
4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 1052 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment. This warranty is limited to def ects in w orkmanship or mater ials, and does not cov er customer damage, ab use or una ...
-
Patton electronic 1052 - page 5
5 1.3 SERVICE All warranty and non-w arranty repairs m ust be returned freight prepaid and insured to P atton Electronics. All retur ns must hav e a Return Materi- als A uthorization number on the outside of the shipping container . This number ma y be obtained from P atton Electronics T echnical Service at: T el: (301) 975-1007 E-mail: support@pat ...
-
Patton electronic 1052 - page 6
6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear par ts and labor. If any questions or problems arise during installation or use of this product, please do not hesitate to contact P atton Electronics T echnical Support at ...
-
Patton electronic 1052 - page 7
7 3.0 CONFIGURATION The Model 1052 is equipped with 16 DIP s witches that enable configur a- tion of the unit f or a wide variety of applications. This section describes s witch locations and e xplains the diff erent config-urations 3.1 CONFIGURING THE HAR DWAR E DIP SWITCHES S1 and S2 each contain eight internal DIP switches (see Figure 1) that ...
-
Patton electronic 1052 - page 8
8 Figure 2. Opening the Model 1052 case Figure 1 on page 7 shows the orientation of the DIP switches in the “ON” and “OFF” positions. Configuring DIP Switch S1 DIP s witch S1 is where you configure the data r ate, asynchronous or synchronous data f ormat, transmit clock source . The f ollowing table sum- marizes def ault positions of DIP ...
-
Patton electronic 1052 - page 9
9 Each setting represents one synchronous data rate and one asynchro- nous data rate. Note If the S2-1 switch is positioned in the OFF position, the 128 kbps sync data rate/0–38.4 kbps async data rate option is selected. Switch S1-3. Must be set to the On position (Reser v ed). Switch S1-4: Must be set to the ON position (Reser ved). Switch S1-5: ...
-
Patton electronic 1052 - page 10
10 Switch S1-8. Must be set to the Off position (Reser v ed). Configuring DIP switch S2 Use the eight DIP s witches in S2 to enable 19.2 kbps synchronous oper- ation and set the loopback modes . The f ollowing tab le summarizes def ault positions of DIP s witches S2-1 through S2-8. Detailed descr ip- tions of each s witch f ollow the tab le. Switc ...
-
Patton electronic 1052 - page 11
11 Switch S2-2: Must be set to the ON position (Reserved). Switches S2-3. Must be set to the Off position (Reser v ed). Switches S2-4 and S2-5: Not Assigned. Switch S2-6. Must be set to the Off position (Reser v ed). Switch S2-8: Not Assigned. S2-2 S2-2 Setting On Reser v ed S2-3 Description Off Reser v ed S2-6 Description Off Reser v ed ...
-
Patton electronic 1052 - page 12
12 4.0 INSTALLATION Once the Model 1052 has been configured, it is ready to connect to the twisted pair interf ace, to the serial por t, and to the power source . This section tells you ho w to make these connections . Figure 3. Model 1052 Rear P anel 4.1 CONNECTING THE T WISTED PAIR INTERFACE The Model 1052 suppor ts communication between tw o DT ...
-
Patton electronic 1052 - page 13
13 tive and is wired f or a two-wire interface . The signal/pin relationships are shown in Figure 4. Figure 4. Model 1052 twisted pair line interface 4.2 CONNECTING THE CONNECTING THE MODEL 1052/A (RS-232) The Model 1052/A suppor ts RS-232 serial por t connections. This section describes how to connect the serial por ts to your RS-232 equipment. Co ...
-
Patton electronic 1052 - page 14
14 Universal A C Po wer (100–240 V AC) The Model 1052 uses a 5VDC , 2A universal input 100-240V AC , power supply (center pin is +5V). The univ ersal input power supply has a male IEC-320 power entry connector . This po wer supply connects to the Model 1052 by means of a barrel jac k on the rear panel. Many interna- tional power cords are a v ail ...
-
Patton electronic 1052 - page 15
15 5.0 OPERATION Once the Model 1052 is properly configured and installed, it should oper- ate transparently . This sections describes power-up , reading the LED status monitors, and using the b uilt-in loopback test modes . 5.1 POWER-UP Bef ore applying power to the Model 1052, read section 4.3, “P ower Con- nection” on page 13 to ensure that ...
-
Patton electronic 1052 - page 16
16 APPENDIX A MODEL 1052 SPECIFICA TIONS A.1 T RANSMISSION FORMAT Synchronous or asynchronous A.2 T RANSMISSION LINE Single unconditioned twisted pair A.3 CONTROL SIGNALS CD and R TS A.4 CLOCKING Internal, external, or receive loopback A.5 DISTANCE Distance, max, all data rates: • 10.1 miles (16.4km) on 19 A WG (0.9mm) wire • 7.2 miles (11.5 km ...
-
Patton electronic 1052 - page 17
17 A.10 T EMPERATURE RANGE 32–122°F (0–50°C) A.11 ALTITUDE 0–15,000 f eet (0–4,572 meters) A.12 HUMIDITY 5–95% non-condensing A.13 WEIGHT 2.01 lbs. (1.0 kg) A.14 LINE INTERFACE T ransformer coupled 1500 V AC isolation ...
-
Patton electronic 1052 - page 18
18 APPENDIX B MODELS 1052/A F ACTOR Y REPLACEMENT P ARTS AND ACCESSORIES Model # Description 1052/A RS232 iDSL Modem 12V -PSM 12 VDC Po wer Supply Module 24V -PSM 24 VDC Po wer Supply Module 48V -PSM 48 VDC Po wer Supply Module 08055DCUI 100-240V A C (+5V ±5% reg. DC/2A) Universal Input Adapter 0805EUR European Po wer Cord CEE 7 (“A”) 0805UK U ...
-
Patton electronic 1052 - page 19
19 APPENDIX C MODEL 1052/A INTERF ACE PIN ASSIGNMENTS RS-232 INTERF A CE (DB-25 Female Connector) (DCE Orientation) Pin # Signal 1 Shield GND 2 TD (T ransmit Data) (DTE Source) 3 RD (Receiv e Data) (DCE Source) 4 RTS (Request to Send) (DTE Source) 5 CTS (Clear to Send) (DCE Source) 6 DSR (Data Set Ready) (DCE Source) 7 SGND (Signal Ground) 8 CD (Ca ...
-
Patton electronic 1052 - page 20
20 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ ___________________________________________________ ...
У вас вопрос, касающийся Patton electronic 1052?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Patton electronic 1052, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Patton electronic 1052 со всей вероятностью он захочет поделиться методом ее решения.