Русский dropdown-ico

Инструкция обслуживания Snapper MZM2300KH, ZM5202M, ZM6102M

35 страниц 0.94 mb
Скачать

Перейти на страницу of 35

Summary
  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 1

    Safety Instructions & Operator’s Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 0 POWER UNIT MODELS MZM2300K H MOWER UNIT MODELS ZM5201M ZM6101M MODEL NUMBER EXPLA NA T ION M Z M 23 00 KH MODEL DESIGNA TION ENGINE T YPE DRIVE SYST EM TYPE SERIES DESIGNATION MOW ER ORIENTA TION ENGINE HP POWER UNIT M – Middl e M arket 23 – En ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 2

    2 IMPORTA N T SA FETY INSTRUCTIONS WARNING: This pow erful cuttin g machine is capable of amp utating hand s and feet and can t hrow ob jects that can cause injury and damag e! Failure to comply wit h the following SAFETY in st ructions could resu lt in serious injury or death to the ope rator or other persons. The ow ner of the machine must unders ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 3

    3 IMPORTA NT SA FETY INSTRUCTIONS PREPA RATION (Continued From Pre v ious Pa ge) 4. Handle f uel with ext ra care. Fuels are flammable and v apors are explosive. Use only an appro ved fuel co ntainer. DO NOT remove fuel cap or add fuel with engine running. A dd or drain fuel outdoors only with engine stopped and cool. Clean spilled fuel from m achi ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 4

    4 IMPORTA NT SA FETY INSTRUCTIONS MA INTENA NCE (Continued From Pre v ious Pa ge) 7. Disconnect batte ry be fore per forming maintenance or service. Cr anking engine could cause injury. Disconnect n egative (black) cable from batter y fir st and positive (red) cable last. Reconnect positive first a nd negative last. Char ge battery in an open, well ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 5

    5 TABLE OF CONTENTS IMPORTA NT SAFETY INSTRUCTIONS ................................................ 2-4 TA BLE OF CO NTENTS ............................................................................. 5 SECTION 1 - FA MILIAR IZA TION .............................................................. 6 SECTION 2 –SA FETY MESSA GES AND SY MBOLS ...... ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 6

    6 Section 1 - FA MILIA RIZA TION FIGURE 1.1 1. 1 INT RODUCTION This manual has been prepar ed for the operator’s of the SNAPPER MID MOUNT Z-RIDER. Its purpos e, aside from recom m ending standard operating procedur es and routine s ervice requirem ents, is to pr omote SAFET Y through the use of acc epted operating practices. Read, Understand and ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 7

    7 Section 2 – SA FETY MESSA GES A ND SYMBOLS ENGINE CONTROLS ENGINE SPEED RA BBI T “FA ST” CHOKE CHOKE “ON” TURTLE “SLOW” RA BBI T “FA ST” ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 8

    8 Section 2 – SA FETY MESSA GES A ND SYMBOLS KEYSW ITCH BLA DE SW ITCH HOUR ME TER BLA DES ENGAGED “ON” BLA DES DISENG A GED “OFF” MOTION CONTROL MULTI -DIRECTIONA L “STOP” “RUN” “STA RT ” REA D OPERAT OR’S M A NUAL BEFORE OP E RATING MACHINE DA NGE R! ROT A TING BL ADES KEEP CHILD REN A ND OT HERS OUT O F MOWING A REA DA NG ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 9

    9 Section 3 - OPERA TING INSTRUCTIONS 2.1 PRE-STA RT CHECK LIST Make the following c hecks and per form the service required bef ore each start-up. 2.1.1. Check tires and add or release air as needed to bring press ure to 12 psi in drive tires . Pressure in front dec k caster wheels should be 25 psi. 2.1.2. Check guards, def lectors and cover s to ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 10

    10 Section 3 - OPERA TING INSTRUCTIONS 2.2 STA RTING & STOPPING – ENGINE, BLA DES, PA RKING BRAKE This mac hine is equipped with dual hydrostatic wheel drive transm issions. Each transm ission is controlled by a single motion c ontrol lever or joystick. T his single c ontrol lever (joystick) controls the direction of motion, For ward and Reve ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 11

    11 Section 3 - OPERA TING INSTRUCTIONS 2.2.5. PA RKING BRA KE 1. Engage park ing brake by pulling the par king brak e lever back to the engaged pos ition. NOTE : Motion control lever ( joy stick ) m ust be in the Neutral position to engage brake. See Figure. 2.6. NOTE: Engaging the parking brak e lock s the m otion control lever (j oy s tick) in th ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 12

    12 Section 3 - OPERA TING INSTRUCTIONS 2.3 CUT TING HEIGHT ADJUSTMENT 1. Adjust cutting height as desired to any position, using deck lift lever. See Figur e 2.8. NOTE: T he engine does not have to be running to adjust cutting height. FIGURE 2.8 2.4 OPERA TION- M OTION CONTROLS 2.4.1. DRIVING M A CHINE 1. Start engine. Releas e parking brak e. 2. M ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 13

    13 Section 4 - MA INTENA NCE 3.1 INTRODUCT ION To retain the quality of the SNAPPER m ower, use genuine SNAPPER replacem ent parts only. Contact a local SNAPPER dealer for par ts and service as sistance. For the cor rect part or inf ormation for a particular SNAPPER mo wer, alway s m ention the m odel and serial num ber. SNAPPER recom m ends return ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 14

    14 Section 4 - MA INTENA NCE 3.2.3. CHECK MOWER DRIVE BELT 1. Foot Rest Removal a. Lower deck to lowest setting. b. Remove foot res t. See Figure 3.3. c. R em oval of f oot rest will allow acc ess to deck belt. FIGURE 3.3 2. Check Belt T ension The idler and s pring provide proper belt tension and require no adj ustment. If belt is frayed, slit, se ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 15

    15 Section 4 - MA INTENA NCE 3.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearing s Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, f rom a gr ease gun. See Figure 3.5. FIGURE 3.5 2. Transaxle Check the level of f luid in both of the fluid reservoir s. W ipe away all dir t and debris from around r eservoir c ap before rem oving. ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 16

    16 Section 4 - MA INTENA NCE 3.5 ANNUA LLY (END OF EA CH SEAS ON) (Continued from previous P age) 3.5.2. FUEL FIL TER Service f uel filter as instr ucted below. Turn k ey to “OFF ” pos ition. Engine MUST be stopped and MUST be cold befor e removing f ilter. Clam p fuel line to prevent fuel s pillage or perform filter change when fuel tank and f ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 17

    17 Section 4 - MA INTENA NCE 3.6 DECK REM OVA L (Continued from previous page) 4. Rem ove shoulder bolts, washer s and nuts from rear lif t arm. See Figur e 3.10. FIGURE 3.10 5. Dis connect pull bar f rom f ront axle by removing clevis pins and c otter pins. See Figure 3.11. FIGURE 3.11 6. Pull lock collar bac k and slide power trans fer shaf t awa ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 18

    18 Section 5 - A DJUSTMENTS & REPA IR DA NGER Exercise EXT REME CAUTION w hen making this adjustment, due to clos e proximity of moving parts. 4.1 NEUTRA L POSIT ION A DJUSTM ENTS The j oy s tick controls the m ovem ent and stopping of the mac hine. Move the joy stick to the center or neutral position to stop m achine. IMPO RTA NT: Alw a ys re ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 19

    19 Section 5 - A DJUSTMENTS & REPA IR 4.2 .1. MOWER DEC K A DJU STMENT (L EVELNESS) (Continued) 6. Loos en the nuts and bolts that secure both front and rear deck s upport brackets on the high side of dec k . Located above each suppor t brack et, on the top part of the power unit fram e, are three shim plates. Rem ove the shim plates on both of ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 20

    20 Section 5 - A DJUSTMENTS & REPA IR WA RNING DO NOT attempt any maintenance, adjustmen ts or service with engine running. S TOP engine. STOP blades. Set brake. Remov e key. Remove spark plug wires an d secu re aw ay from spark p lug s. Eng ine an d components are HOT. Avoid se rious burns, allow sufficie nt time for all parts to cool . 4.3 PA ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 21

    21 Section 5 - A DJUSTMENTS & REPA IR 4.5.2. BLADE SHA RPENING 1. Rem ove blade. See Figure 4.5. FIGURE 4.5 2. Inspect condition of blade. See Figure 4.4. 3. If blade is in good condition, s harpen at 22 to 28 degrees . DO NOT shar pen bey ond original cutting edge. See Figure 4.6. FIGURE 4.6 4. Check blade balance after sharpening. If neces sa ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 22

    22 Section 5 - A DJUSTMENTS & REPA IR WA RNING Shield the positive t ermin al with terminal cover located on bat tery harness. T his prevent s metal f rom touching the positive terminal which could cause sparks. Cables must b e connected to battery terminals in the proper position. RE D (Positive) c a bl e must go to the ( + ) terminal. BLACK ( ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 23

    23 Section 5 - A DJUSTMENTS & REPA IR Battery Condition Chart State of Charge Syr inge Hydrome ter Digital Voltmeter Five Ball Hydrometer 100% Charged w/ Sulfate Stop 1.280 12.80v Five Balls Floating 100% Charged 1.265 12.60v Four Balls F loating 75% Charged 1.210 12.40v Three Balls Floating 50% Charged 1.160 12.10v Two Balls Floating 25% Charg ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 24

    24 TROUBLESHOOTING PROBL EM PROBA BLE CA USE CORRECTIVE A CTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. C l ean and check connections for good contact. 4. Defective ignition sw itch. 4. Contact authorized SNA PPER dealer. Engine Will Not Start ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 25

    25 TROUBLESHOOTING PROBLEM PROBA BLE CA USE CORRECTIVE A CT ION Tractor Will Not Move 1. Joystick in the neutral “N” position. 1. Place joystick in desired speed position. Loss Of Traction 2. Ro ll re le a se lever is in “ RO LL ” p os it i on . 2. Mov e roll release lever to the engaged position. 3. Low transmission hy draulic oil level. 3 ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 26

    26 SERVICE SCHEDULE ITEM SERVICE PERFO RMED REF. EA CH USE 5 HRS 25 HRS 50 HRS 100 HRS EA CH SEA SON Engine Oil Check Oil Level Page 9 X Initial Oil Change Page 13 X Periodic Oil Change Page 13 X* A ir Pre-Cleaner Clean Sponge Elem ent Engine Manual & Page 14. X** A ir Cleaner Clean or Replace Engine Manual. X** Spark Plug Replace Engine Manual ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 27

    27 2 YEA R LIMITED WA RRA NTY For two (2) y ears from purchase date f or the original purchaser 's use, SNAPPER , through any author iz ed SNA PPER dealer will replace, fr ee of charge (ex cept for taxes where applicable), any part or parts found upon exam ination by the f actory at McDonough, Georgia, to be defec tive in material or work mans ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 28

    28 PRIMA RY MA INTENA NCE ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 29

    29 PRIMA RY MA INTENA NCE ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 30

    30 PRIMA RY MA INTENA NCE ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 31

    31 PRIMA RY MA INTENA NCE ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 32

    32 NOTES ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 33

    33 NOTES ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 34

    34 NOTES ...

  • Snapper MZM2300KH, ZM5202M, ZM6102M - page 35

    35 Safety Instructions & Operator’s Manual for M ID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES 0 IMPORTANT Snapper products are built using engines that meet or exceed all a pplicable emissions requirements on the date manufactured. The labels on thos e engines contai n very importa nt emissions infor mation and critical safety warnings. R ...

Производитель Snapper Категория Lawn Mower

Документы, которые мы получаем от производителя устройства Snapper MZM2300KH, ZM5202M, ZM6102M мы можем разделить на несколько групп. Это в частности:
- технические чертежи Snapper
- инструкции обслуживания MZM2300KH, ZM5202M, ZM6102M
- паспорта изделия Snapper
- информационные брошюры
- энергетические этикетки Snapper MZM2300KH, ZM5202M, ZM6102M
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Snapper MZM2300KH, ZM5202M, ZM6102M.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Snapper MZM2300KH, ZM5202M, ZM6102M, инструкции обслуживания, короткие инструкции или инструкции пользователя Snapper MZM2300KH, ZM5202M, ZM6102M. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Snapper MZM2300KH, ZM5202M, ZM6102M.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Snapper MZM2300KH, ZM5202M, ZM6102M, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Snapper MZM2300KH, ZM5202M, ZM6102M пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Snapper MZM2300KH, ZM5202M, ZM6102M.

Полная инструкция обслуживания Snapper, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Snapper MZM2300KH, ZM5202M, ZM6102M - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Snapper MZM2300KH, ZM5202M, ZM6102M, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Snapper MZM2300KH, ZM5202M, ZM6102M, которое найдем в данном документе
3. Советы по использованию основных функций устройства Snapper MZM2300KH, ZM5202M, ZM6102M - которые должны облегчить нам первые шаги во время использования Snapper MZM2300KH, ZM5202M, ZM6102M
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Snapper MZM2300KH, ZM5202M, ZM6102M
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Snapper MZM2300KH, ZM5202M, ZM6102M в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Snapper MZM2300KH, ZM5202M, ZM6102M?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Snapper MZM2300KH, ZM5202M, ZM6102M, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Snapper MZM2300KH, ZM5202M, ZM6102M со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)