-
Miele W 504 Plus - page 1
Operating instructions f or W ashing machine W 504 Plus T o avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time. G M.-Nr . 06 107 290 ...
-
Miele W 504 Plus - page 2
Disposal of the packing material The transport and protective packing has been selected from materials which are envir onmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suf focation! Rather than just thr ...
-
Miele W 504 Plus - page 3
Caring for our en vironment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Disposal of your old appliance or machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 W arning and safe ...
-
Miele W 504 Plus - page 4
Adding or removing laundry after a programme has started . . . . . . . . . . . . . . . . 25 Interrupting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Altering a programme once selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Skipping a programme stage . . . . . . ...
-
Miele W 504 Plus - page 5
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Miele W 504 Plus - page 6
T o avoid the risk of accidents and damage to the machine please read these instructions carefully befor e using it for the first time. They contain important infor mation on its safety , use and maintenance. Keep these instructions in a safe place and ensure that new users ar e familiar with the content. Pass them on to any future owner of the mac ...
-
Miele W 504 Plus - page 7
This machine must only be connected to the on-site water supply using a new hose kit. Old hoses must not be re-used. Check the hose regularly for signs of wear and tear . Change in good time to avoid the risk of leaks and subsequent damage. Faulty components must only be replaced by genuine Miele original spare parts. Only when these parts are fitt ...
-
Miele W 504 Plus - page 8
If the correct amount of detergent is dispensed, the machine should not need to be descaled. If, however , you do wish to descale the machine only use proprietary non-corrosive descaling agents and strictly observe the instructions on the packaging. If in doubt, contact the Miele Customer Service Dept. or your Miele Dealer . T extiles which have be ...
-
Miele W 504 Plus - page 9
Y our machine has the following special programmes in addition to the standar d Cottons and Minimum iron programmes. Special programmes – Silks / Hand-washable fabrics which crease easily and do not contain wool can be washed in the Silks / programme (30°C temperatur e only). – Woollens / Hand-washable or machine- washable wool or wool blend f ...
-
Miele W 504 Plus - page 10
Future updates (PC) The indicator or check light marked PC is the interface used by Miele service technicians during servicing work for testing purposes and for updating the machine's programme data. Description of the machine 10 ...
-
Miele W 504 Plus - page 11
Control panel a Start button Starts the wash programme b Additional option b uttons Additional options can be added to the basic programme. Use the top button to select either the Short , the Pre-wash or the Soak option. Use the lower button to select the W ater plus option. Indicator light on = option selected Indicator light off = option not sele ...
-
Miele W 504 Plus - page 12
Important control panel features Programme selector The programme selector is used to set the basic wash programme and the temperature for that pr ogramme. Additional option b uttons Additional options can be added to the basic programme. Use the top button to select either the Short , the Pre-wash or the Soak option. Use the lower button to select ...
-
Miele W 504 Plus - page 13
Before using the machine for the first time ensure that it is corr ectly installed and connected. See "Installation and connection". Also check that the drain filter is securely tightened. Otherwise there is a risk of water leakage during use. For safety reasons spinning is not possible until the machine has been prepar ed for using for t ...
-
Miele W 504 Plus - page 14
Energy and water consumption – W ater consumption and energy usage are determined by the size of the load. T o make the most out of your machine, load the maximum dry load for the programme you ar e using. – Use the Automatic or the Quick wash programmes for small loads. – When smaller amounts of laundry are washed using the Cottons programme ...
-
Miele W 504 Plus - page 15
Brief instructions Please note: T o help familiarise yourself with how to use your washing machine please read the sections "Before washing", "Selecting a programme" and "At the end of a programme" in detail. A Sort the laundr y into colours and fabric types Selecting a programme: B Switch on the washing machine C Open ...
-
Miele W 504 Plus - page 16
Programme c har t Cottons 30°C to 95°C 9ö876 Fabric Cottons and linen fabrics, e.g. bed linen, table linen, towelling, jeans, underwear , T -shirts, nappies. Additional options Short, Pre-wash, Soak, W ater plus Notes – Only use the Cottons 95°C programme for heavily soiled laundry . – For heavily soiled laundry and/or soiling which has bee ...
-
Miele W 504 Plus - page 17
Delicates cold to 40°C 21ac Fabric For delicate garments made of synthetic fibres, mixed fibres and for easy care cotton shirts and blouses. Curtains, including net cur tains, specified as machine- washable by the manufacturer . Additional options Short, Pre-wash, Soak Notes – Laundry remains relatively cr ease-free for easier ir oning. – Dust ...
-
Miele W 504 Plus - page 18
Quick wash 40°C 7 Fabric V er y lightly soiled fabrics, which can be washed in the Cottons programme. Notes – Use less detergent (as for a half load). – If fabrics have a high proportion of man-made fibres it is advisable to programme the machine for "Gentle Action". See "Programmable functions". Note that this pr ogramme i ...
-
Miele W 504 Plus - page 19
/ Hand wash (If no temperature is specified use the lowest temperature or cold) h Do not wash apf Dry clean D Do not dry clean w Clean professionally x Suitable for chlorine bleaching z Do not use chlorine bleach T umble dry q At normal temperature r At low temperature s Do not tumble dry Ironing I Hot iron H Medium hot iron G Cool iron J Do not ir ...
-
Miele W 504 Plus - page 20
Before washing A Sort the laundr y ^ Empty all pockets. , Foreign objects (e.g. nails, coins, paper clips, etc.) can cause damage to garments and components in the machine. ^ Badly soiled areas, e.g. collars and cuffs, and water soluble stains can be pre-tr eated with bar soap, liquid detergent or detergent mixed into a solution or paste. With part ...
-
Miele W 504 Plus - page 21
Selecting a programme B Switch on the washing machine ^ Press in the I-On/0-Off button. C Open the drum door ^ Press the Door button and open the drum door . D Load the drum ^ Unfold the laundry and load loosely in the drum. T o achieve best results it is advisable to make up mixed loads consisting of both large and small items. This improves the w ...
-
Miele W 504 Plus - page 22
Additional options H Select additional option(s) if required. Additional options can be selected as long as they are compatible with the basic programme being used. Each press of the top button selects the additional option in the following order: Short , Pre-wash , Soak , no selection. Use the lower button to select or deselect the W ater plus opt ...
-
Miele W 504 Plus - page 23
I Add deter gent It is important to dispense the correct amount, because . . . . . . too little results in the following: – Laundry will not be properly clean and will in time become grey and hard to the touch. – Greasy particles cling to the laundry . – Limescale deposits on the heater elements. . . . too much results in the following: – E ...
-
Miele W 504 Plus - page 24
At the end of a programme When the Anti-crease/Finish indicator light comes on the laundry can be removed fr om the drum. (This light stays on at the end of the programme and remains on until the selector is turned back to the Finish position). K Open the drum door ^ Press the Door button. L Remove the laundry . , Only remove laundry from the machi ...
-
Miele W 504 Plus - page 25
Adding or remo ving laundry after a programme has started Laundry can be added or removed after the programme has started when using the following programmes: – Cottons – Minimum iron – Quick wash – Automatic – Starch ^ Press the Door button in and hold it until the door springs open. ^ Add or remove items. ^ Close the door . The programm ...
-
Miele W 504 Plus - page 26
Interrupting a programme ^ Switch the washing machine off with the I-On/0-Off button. T o continue with the same programme: ^ Switch the washing machine back on again with the I-On/0-Off button. Altering a programme once selected The machine will accept the following changes after a programme has started: – at any time after the start, the spin s ...
-
Miele W 504 Plus - page 27
Programme sequence Main wash Rinses Spinning W ater level W ash rhythm W ater level No of rinses Rinse and interim spin Final spin Cottons d a ( 2-3 1) L 2) L Minimum iron d a e 2-3 3) L 2) L Delicates e b e 3 – L Silks ( d ( 2 – L Woollens ( c ( 2 L 2) L Quick wash d a ( 2 L 2) L Automatic d a e 2 L 2) L Starch –– d 1 – L Separate rinse ...
-
Miele W 504 Plus - page 28
This washing machine has fully electronic contr ols with automatic load recognition. This machine takes in the right amount of water requir ed for the programme depending on the amount of laundry and its absorbency rate. This means that programme cycles and durations shown in the display can vary . The programme sequences outlined below are based o ...
-
Miele W 504 Plus - page 29
All modern detergents produced for automatic washing machines are suitable, including liquid, compact (concentrated), tablets, liquid tablets and special application detergents. Use dispensing aids, e.g. balls, if these are supplied with the detergent. T ablets are suitable for full loads but note that it may be impractical to reduce tablets for sm ...
-
Miele W 504 Plus - page 30
Fabric conditioner s and liquid starc h Fabric conditioners make garments soft to handle and help prevent static cling when tumble drying. Starch stif fens and gives body to items of laundry , e.g. shirts, tablecloths and bed linen. ^ Dispense according to the amount specified on the packaging. A utomatic dispensing of fabric conditioner or liquid ...
-
Miele W 504 Plus - page 31
, Disconnect the machine from the mains electricity supply and withdraw the plug from the socket before cleaning the machine. , The washing machine must not be hosed down. External casing and fascia panel ^ Clean the casing with a mild non- abrasive cleaning agent or soap and water using a well wrung-out cloth. Wipe dry with a soft cloth. ^ The dru ...
-
Miele W 504 Plus - page 32
^ Clean the siphon. 1 . Remove the siphon from compartment § and rinse under warm running water . Clean the siphon tube in the same way . 2 . Replace the siphon. If starching fr equently , thoroughly clean the siphon and siphon tube regularly . A build-up of starch will cause them to get clogged. Cleaning the detergent dispenser drawer housing ^ U ...
-
Miele W 504 Plus - page 33
Cleaning the water inlet filters The washing machine has two filters to protect the inlet valves. These filters should be checked every six months or so, or more often if ther e are fr equent interruptions to the water supply . T o c lean the filter in the union in the open end of the inlet hose: ^ First turn off the stopcock. ^ Unscrew the thr ead ...
-
Miele W 504 Plus - page 34
With the help of the following notes minor faults in the perfor mance of the appliance, some of which may result fr om incorrect operation, can be put right without contacting the Service Department. , Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with local and national safety r ...
-
Miele W 504 Plus - page 35
The wash programme stops and a fault indicator light comes on. Prob lem P ossible cause Remedy A The Check drain light flashes. The water outlet is blocked. Clean the fluff filter and the drain pump as described in "Problem solving guide - Opening the drum door in the event of a blocked drain outlet and/or power failure". The drain hose h ...
-
Miele W 504 Plus - page 36
A fault indicator light comes on but the wash pr ogramme continues as normal Prob lem P ossible cause Remedy A The Check drain light flashes. The drain outlet is restricted. Clean the drain filter and the drain pump as described in "Problem solving guide - Opening the drum door in the event of a blocked drain outlet and/or power failure". ...
-
Miele W 504 Plus - page 37
General prob lems or an unsatisfactory wash result Prob lem P ossible cause Remedy The machine shakes during the spin cyc le. The four feet are not resting evenly on the floor . Level the machine. See installation. The laundry has not been spun satisfactorily . The spin speed selected was too low . Select a higher spin speed next time. The pump mak ...
-
Miele W 504 Plus - page 38
Prob lem P ossible cause Remedy Liquid detergent does not give the required result. Liquid detergents do not contain bleaching agents. They do not remove fruit, cof fee and tea stains. – Use a general purpose washing machine powder containing a bleaching agent. – Pour stain removers into compart - ment j of the dispenser drawer and liquid deter ...
-
Miele W 504 Plus - page 39
The drum door does not open when y ou press the Door button. Prob lem Remedy The machine is not connected to the electricity supply . Put the plug in the socket and switch on. The washing machine is not switc hed on. Switch the machine on with the I-On/0-Off button. P ower cut. Open the drum door as described in the section "Opening the door i ...
-
Miele W 504 Plus - page 40
Opening the drum door in the event of a b locked drain outlet and/or power failure ^ Switch the washing machine off. There is a lever behind the detergent drawer fascia panel. ^ Remove the lever . ^ Use it to open the access flap. Blocked drain outlet If the drain outlet is blocked, up to 25 litres of water will be r etained in the machine. , Cauti ...
-
Miele W 504 Plus - page 41
Once the flow of water ceases: ^ Remove the drain filter completely . ^ Clean it thoroughly . ^ Remove any foreign objects (e.g. buttons, coins, etc.) and fluff fr om the filter housing. T ur n the impeller by hand to check that it rotates fr eely . Any foreign object causing an obstruction should be removed. ^ Put the drain filter back in place an ...
-
Miele W 504 Plus - page 42
Customer contact In the event of any faults which you cannot remedy yourself please contact – Y our Miele dealer or – Y our nearest Miele Service Department (see back cover for the address). When contacting your Dealer or the Service Department, please quote the model and serial number of your appliance, both of which are shown on the data plat ...
-
Miele W 504 Plus - page 43
Front vie w a Inlet hose (tested to withstand pressur e of at least 7,000 kPa) b Electricity supply cable c - f Flexible drain hose (with detachable swivel elbow) g Control panel h Detergent dispenser drawer i Drum door j Access to drain filter , drain pump and emergency release k Handle recesses for moving the machine l Four height adjustable feet ...
-
Miele W 504 Plus - page 44
Rear view a Protruding lid for holding when moving the machine b Electricity supply cable c Inlet hose (tested to withstand pressur e of at least 7,000 kPa) d Drain hose e T ransit bar covers f Restraining clip for inlet hose and drain hose g Restraining clips for transit bars when removed Installation and connection 44 ...
-
Miele W 504 Plus - page 45
Installation surface A concrete floor is the most suitable installation surface for a washing machine, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. Please note the following points: ^ The machine must be level and securely positioned. ^ T o avoid vibrations during spinning, the machine shoul ...
-
Miele W 504 Plus - page 46
^ Using the spanner supplied turn the left-hand transit bar 90°, then ^ withdraw the transit bar . ^ T ur n the right-hand transit bar 90°, then ^ withdraw the transit bar . Installation and connection 46 ...
-
Miele W 504 Plus - page 47
^ Fit the covers on to the two holes. Then plug the holes as shown with the caps. ^ Secure the transit bars to the back of the washing machine. Make sure that holes b are fitted over r etainers a . , The washing machine must not be moved without the transit bars in place. Store the transit bars as shown or keep them in a safe place for future use. ...
-
Miele W 504 Plus - page 48
Levelling the mac hine The machine must stand perfectly level on all four feet to ensure safe and proper operation. Incorrect installation may incr ease electricity and water consumption and may cause the machine to move about. Screwing out and adjusting the feet The four adjustable screw feet ar e used to level the machine. All four feet are screw ...
-
Miele W 504 Plus - page 49
The fitting of building under kits and stacking kits must only be undertaken by qualified and competent persons, in accordance with the instructions supplied with the kit. Building under a continuous worktop/in a kitc hen run If you wish to push your machine under a worktop and there is space to do this without removing the lid , the conversion kit ...
-
Miele W 504 Plus - page 50
The Miele water protection system The Miele water protection system protects the washing machine fr om water damage. The system consists of three main components: 1) the inlet hose 2) the electronic unit and the washing machine housing 3) the drain hose 1) Inlet hose The inlet hose can withstand pressur e of more than 7,000 kPa. 2) Electronic unit ...
-
Miele W 504 Plus - page 51
Connection to the water supply The machine should be connected to a mains water supply in accordance with local and national safety regulations. The German authorities do not require it to have a non-return valve as the washing machine has been designed to comply with DIN regulations. The machine is designed to operate with a flow pressur e of betw ...
-
Miele W 504 Plus - page 52
Connection to the drainage system The machine drains via a drain pump with a delivery head of 1 metre*. The drain hose must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if requir ed, with a sharp twist and pull. If requir ed, the drain hose can be extended to ...
-
Miele W 504 Plus - page 53
Electrical connection U .K. All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the appliance until after installation work has been carried out. The appliance is supplied with a mains cable with moulded plug ready fo ...
-
Miele W 504 Plus - page 54
Load Consumption data Energy W ater Duration in kWh in litres Short Normal Cottons 95°C 5.0 kg 1.70 45 1 h 42 min 1 h 57 min 60°C 1) 5.0 kg 0.85 45 – 1 h 56 min 60°C 5.0 kg 0.85 45 1 h 26 min 1 h 56 min 40°C 1) 5.0 kg 0.50 45 – 1 h 56 min 40°C 5.0 kg 0.50 45 1 h 26 min 1 h 56 min Minimum ir on 40°C 1) 2.5 kg 0.45 49 – 1 h 16 min 40°C 2 ...
-
Miele W 504 Plus - page 55
Height 85.0 cm Width 59.5 cm Depth 58.0 cm Depth with door open 97.5 cm Weight 93 kg Maximum floor load 1600 Newton (approx. 160 kg) Capacity 5 kg dry laundr y V oltage see data plate Rated load see data plate Fuse rating see data plate Consumption data see "Consumption data" W ater flow pressur e minimum 100 kPa (1 bar) W ater flow press ...
-
Miele W 504 Plus - page 56
56 ...
-
Miele W 504 Plus - page 57
Progr ammable functions f or changing standard settings ...
-
Miele W 504 Plus - page 58
The programmable functions can be used to tailor washing programmes to suit your individual requir ements. The programmable functions ar e activated with the help of the Start button and the programme selector . W ater plus system Selecting the W ater plus additional option increases the water intake in the programmes listed below . The water intak ...
-
Miele W 504 Plus - page 59
Follow steps A to G to pr ogramme and store in memory . Before you begin, first ensur e that: – The washing machine is switched off. – The machine is properly closed. – The programme selector is at Finish . A Press the Start button and keep it pressed in whilst carrying out steps B to C . B Switch the machine on with the I-On/0-Off button. C ...
-
Miele W 504 Plus - page 60
Gentle action Activating gentle action reduces the drum action and is suitable for washing slightly soiled articles more gently . It should be activated for garments with a single bar under the care label and for articles which feel too hard after they have been dried. Gentle action can be used with the Cottons , Quick wash , Starch and Auto - mati ...
-
Miele W 504 Plus - page 61
T op-up rinse for Cottons When this is activated, additional water flows into the drum at the end of the main wash to cool the suds down. Hot suds can damage plastic drainage pipes. T op-up rinse takes place when temperatures of 95°C and 75°C ar e selected. T op-up rinse should be activated: – to prevent the danger of scalding if the drain hose ...
-
Miele W 504 Plus - page 62
Memory function If an additional option(s) is selected for a programme, and / or the spin speed is altered, the machine stor es these changes in memory at the star t of a programme. When that particular programme is chosen again, the display will show the additional option(s) and / or spin speed which have been stored for that programme in the memo ...
-
Miele W 504 Plus - page 63
Soak A length of time of between 30 minutes and 2 hours can be programmed in 30 minute increments for the soak process. If the soak button is pressed the selected soak time will be carried out for the period selected before the wash programme is run. The machine is set as standard to a two hour soak time. Follow steps A to G to pr ogramme and store ...
-
Miele W 504 Plus - page 64
Alteration rights reserved/2506/W 504 Plus M.-Nr . 06 107 290 / 04 e n-G B ...
У вас вопрос, касающийся Miele W 504 Plus?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Miele W 504 Plus, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Miele W 504 Plus со всей вероятностью он захочет поделиться методом ее решения.