-
AEG HG795440XB - page 1
HG795440XB IE GB EN GAS HOB USER MANUAL ...
-
AEG HG795440XB - page 2
FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG we ...
-
AEG HG795440XB - page 3
CONTENTS 4 Safety information 7 Installation 12 Product description 12 Operation 15 Helpful hints and tips 16 Care and cleaning 18 What to do if… 19 Technical data 20 Environment concerns The following symbols are used in this user manual : Important information concerning your personal safety and information on how to avoid damaging the applianc ...
-
AEG HG795440XB - page 4
SAFETY INFORMATIO N WARNING! These instructions are only valid in the countries whose symbols appear on this booklet's cover. For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the op ...
-
AEG HG795440XB - page 5
• The cookware must not enter the control zone. • Make sure that the cookware does not protrude over the edges of the cooking surface and that it is centrally positioned on the rings in order to avoid safety risks. • Do not use unstable cookware or cookware with damaged bottom. There is a risk of tilt- ing and accident. • Do not put flammab ...
-
AEG HG795440XB - page 6
• Before installation, make sure that the local supply conditions (gas type and pressure) agree with the adjustment of appliance. The adjustment conditions for the appliance are on the rating plate, which you can find near the gas supply pipe. • This appliance is not connected to a combustion products evacuation device. It must b e installed an ...
-
AEG HG795440XB - page 7
INSTALLATION WARNING! The following instructions about installation, connection and ma intenance must be carried out by qualified personnel in compliance with standards and local regulations in force. Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regula- tions (Current Edition) and ...
-
AEG HG795440XB - page 8
1 2 3 1 End of shaft with nut 2 Washer 3 Elbow Connection to the gas supply should be with either rigid or semi - rigid pipe, i.e. steel or cop- per. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and instal ...
-
AEG HG795440XB - page 9
Adjustment of minimum level To adjust the minimum level of the burners: 1. Light the burner. 2. Turn the knob on the minimum position. 3. Remove the knob. 4. With a thin screwdriver, adjust the by - pass screw position. 1 1 The by - pass screw – If you change from natural gas 20 mbar to liquid gas, fully tighten the by - pass screw in. – If you ...
-
AEG HG795440XB - page 10
Electrical Requirements Permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety the installation must be done by a quali- fied electrician (e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Inst ...
-
AEG HG795440XB - page 11
WARNING! Make sure that the cut off plug is disposed of safely. A cut off plug put into a 13 amp sock- et is a safety hazard. There is a risk of electrical shock. The replacement of the electrical cable must be done by a qualified electrician or compe- tent person, according to the current regulati ons. Replacement of the connection cable To replac ...
-
AEG HG795440XB - page 12
Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven fr om the unit. 50 cm 2 360 cm 2 180 cm 2 120 cm 2 PRODUCT DESCRIP ...
-
AEG HG795440XB - page 13
Always light the burner before you put cookware. To light the burner: 1. Turn the control knob counterclockwise to the maximum position ( ) and push it down. 2. Keep the control knob pushed for approximately 5 seconds; this will let thermocouple to warm up. If not, the gas supply will be interrupted. 3. Adjust the flame after it is regular. If afte ...
-
AEG HG795440XB - page 14
1 2 3 4 1 Burner cap 2 Burner crown 3 Ignition candle 4 Thermocouple WARNING! Do not keep the control knob pushed for more than 15 seconds. If the burner does not light after 15 seconds, release the control knob, turn it into off posi- tion and try to light the burner again after minimum 1 minute. In the absence of electricity you can ignite the bu ...
-
AEG HG795440XB - page 15
When you install the grate of the Triple Crown burner afterwards, align the hollow part of the grate with the reference on the plate attached to the glass. CAUTION! Be very careful when you put the pan supports back on their position. There is a risk of scratching the glass hob top. HELPFUL HINTS AND TIPS Energy savings • If possible, always put ...
-
AEG HG795440XB - page 16
WARNING! Pots must not enter the control zone. Flame will heat up the control zone. Do not put the same pan on two burners. WARNING! Make sure pot handles do not protrude over the front edge of the cooktop and that pots are centrally positioned on the rings in order to achieve maximum stabi lity and to obtain lower gas consumption. Do not place uns ...
-
AEG HG795440XB - page 17
• The pan supports are not dishwasher proof; they must be washed by hand . • When you wash the pan supports by hand, take care when you dry them as the enamel- ling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner. • Make sure you position the pan supports correctly after cleaning. • To mak ...
-
AEG HG795440XB - page 18
WHAT TO DO IF… Problem Possible cause Remedy There is no s park when lighting the gas • There is no electrical su pply • Make sure that the unit is connected and the electrical supply is switched on. • Control the fuse. If the fuse is released more than one time, refer to a qualified electrician. • Burner cap and crown are placed uneven ? ...
-
AEG HG795440XB - page 19
MOD. PROD.NO. SER.NO DA T A MOD. PROD.NO. SER.NO DA T A MODEL MODEL MOD. PROD.NO. SER.NO. 03 IT MADE IN IT AL Y TYPE 230V -50Hz IP20 0049 1 2 3 1 Stick it on Guarantee Card and send this part 2 Stick it on Guarantee Card and keep this part 3 Stick it on instruction booklet These data are necessary to help you quickly and correctly. These data are a ...
-
AEG HG795440XB - page 20
Electric supply: 230 V ~ 50 Hz 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse Category: II2H3+ Gas connection: R 1/2" Gas supply: G20 (2H) 20 mbar Appliance class: 3 By - pass diameters Burner Ø By - pass in 1/100 mm Auxiliary 28 Semi - rapid 32 Triple Crown 56 Gas burners BURNER NORMAL POWER REDUCED POWER N ...
-
AEG HG795440XB - page 21
Packaging material The packaging materials are friendly to the environment and can be recycled. The plastic components are identified by marking: >PE<,>PS<, etc. Discard the packaging materials as household waste at the waste disposal facilities in your municipality. 21 ...
-
AEG HG795440XB - page 22
22 ...
-
AEG HG795440XB - page 23
23 ...
-
AEG HG795440XB - page 24
www.aeg.com/shop 397249201 - A - 412011 ...
У вас вопрос, касающийся AEG HG795440XB?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с AEG HG795440XB, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с AEG HG795440XB со всей вероятностью он захочет поделиться методом ее решения.