-
Fujitsu S300M - page 1
Please read this guide bef ore connecting the scanner to your computer. For further details, refer to the "ScanSnap S300M Oper ator’ s Guide" included in the supplied ScanSnap Setup CD-ROM. Contents Introduction ............... ................ ................ .......... 1 Conventions .............. ................ ................ .. ...
-
Fujitsu S300M - page 2
1 Introduction Thank you for purchasing our Color Image Sc anner, ScanSnap S300M (hereinafter referred to as "the ScanSnap"). The ScanSnap S300M is a color image scanner capable of double-sided scanning in both monochrome and color. It is complete Office Solution, which helps you improve productivity and solve scanning prob lems in your o ...
-
Fujitsu S300M - page 3
ScanSnap S300M Getting St arted 2 • Y ou can send off the scanner image by e-mail or outp ut the scanned image to the printer immediatel y after scanning! W ithout starting applications , you can attach the scanned image to e-mail or make copies of the scanned image by outputting it to the printer . (*The ScanSnap S300M Scanner does NOT co mply w ...
-
Fujitsu S300M - page 4
3 ScanSnap and the Manuals The ScanSnap S300M consists of: Following manuals are prepared for you: Component Specification S300M Color image scanner ScanSnap Manager ScanSnap's driver to scan and save documents Cardiris Software for recognizing business cards ( OCR) Manual Description ScanSnap S300M Getting S tarted (This manual) Provides basi ...
-
Fujitsu S300M - page 5
ScanSnap S300M Getting St arted 4 Regulatory Information FCC declaration This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against ha rmful int erference in a re sidential installation. This equipment gener ...
-
Fujitsu S300M - page 6
5 Bescheinigung des Herstellers / Importeurs Für den S300M wid folgendes b e scheinigt: • In Übereinsstimmung mit den Bestimmun gen der EN45014(CE) funkentstört • Maschinenlärminformationsvero rdnung 3. GPSGV : Der höchste Schalldruck- pegel beträgt 70 dB (A) oder weniger , gemäß EN ISO 7779. Dieses Gerät wurde nicht für die Benut zun ...
-
Fujitsu S300M - page 7
ScanSnap S300M Getting St arted 6 Conventions Warning Indications Used in This Manual Symbols Used in This Manual This manual uses the following symbols in explanations in addition to warning indications: WARNING This sign warns the operator that improper use, indicated with this sign, may cause death or severe injury of the operator or people in t ...
-
Fujitsu S300M - page 8
7 Screen Examples in This Manual The screen examples in this manual are subjec t to change without notic e in the interest of product improvement. If actual screens differ from those used as examples in this manual, operate by following the actual ones referring to the User's Manual of the ScanSnap. The screenshots used in this manual are for ...
-
Fujitsu S300M - page 9
ScanSnap S300M Getting St arted 8 Safety Precautions FOLLOW THESE INSTRUCTIONS AND BE SURE TO HEED ALL WARNINGS AND CAUTIONS DESCRIBED BELOW. The following describe s important warnings. WARNING Do not touch the power plug, or c onnect/disconnect the power or USB bus power cable with wet hands. Doing so might cause electric shock. A damaged power o ...
-
Fujitsu S300M - page 10
9 If you detect heat coming from the devic e or detect oth er problems such as smoke, strange smells or noises, immediately turn off the scanner , a nd disconnect its power plug from the power outlet, or unplug the USB bus power cable from the computer . Make sure that the smoking has stopped, and then contact the store wher e you bought the scanne ...
-
Fujitsu S300M - page 11
ScanSnap S300M Getting Start ed 10 The following describe s important cautions. Do not leave the scann er in the direct s unlight, at high temperature such as in a car in the scorching sun, or near heat ing app aratus. Doing so might cause excessive heat to build up insid e the scanner , causing heating, defo rming, or melting of the scanner p arts ...
-
Fujitsu S300M - page 12
11 When handling the paper , be careful not to cut your fingers by the paper . ...
-
Fujitsu S300M - page 13
ScanSnap S300M Getting Start ed 12 Chapter 1 Prep aration This chapter describes necessary prep aration s before using the ScanSnap. 1.1 Checking the Content s of the Package This manual describes how to install and c onnect th e ScanSnap to your computer, and describes basic operations of the ScanSnap. Refer to the following manuals when necessary ...
-
Fujitsu S300M - page 14
13 1.2 Names and Functions of Part s When you unpack the ScanSnap package, ma ke sure that all parts are included. Refer to the package contents list included in the ScanSnap package box. ■ Front V iew CAUTION T o avoid danger of suffocation, keep the packaging materials away from small children’s reach and prevent them from putting the materia ...
-
Fujitsu S300M - page 15
ScanSnap S300M Getting Start ed 14 ■ Rear View For the Document Specification, refer to " 3.2 Paper Sizes of Documents to be Scanned " in " ScanSnap S300M Operator's Guide " stored in the ScanSnap Setup CD-ROM. ATTENTION The ScanSnap is turned on/off in conjunction with the connected computer , or with opening/closing of ...
-
Fujitsu S300M - page 16
15 Chapter 2 Connecting the ScanSnap This chapter describes how to connect the ScanSnap to your computer. 2.1 Inst alling the Supplied Software Before connecting the ScanSnap to your compu t er, install the following software on your computer. ( 3 : Supported, –: Not supported) *1) When the operating system you are using is Mac OS X v10.2.8. *2) ...
-
Fujitsu S300M - page 17
ScanSnap S300M Getting Start ed 16 4. Scroll down and read License Agreement to the end . Then click the [Continue] button , and install Cardiris, by fol lowing instruction on the screen. By default, Cardiris i s instal led on the Applications Folder . 5. After installation, Mac OS X restarts, and the Cardiris icon appears on the Dock menu. 6. Chec ...
-
Fujitsu S300M - page 18
17 4. After the installation is complete, eject the CD-ROM from the CD-ROM drive. ⇒ The ScanSnap Manager icon appears on the Dock menu . HINT The status of the ScanSnap Manager icon will change from to after connecting the ScanSnap to your computer . The displayed icon in the Dock menu varies depending on the cable connection you made. • Power ...
-
Fujitsu S300M - page 19
ScanSnap S300M Getting Start ed 18 2.2 Connecting the ScanSnap When the installation of the above p rograms is complete, connect the ScanSnap to your computer. ■ Connecting the cable Connect the ScanSnap to a power supply in either of two ways below: After connecting to a power source with th e cable above, connect to your computer with a USB cab ...
-
Fujitsu S300M - page 20
19 • When connecting with the Power cable: Use the power cable and USB cable . 1. Connect the Power cable. Remove the adhesive label cove ring the USB and power connectors. Connect to the ScanSnap’ s pow er connector and an outlet. 2. Connect the USB cable. Connect the USB cable to both the ScanSnap and your computer . 3. After power and USB po ...
-
Fujitsu S300M - page 21
ScanSnap S300M Getting Start ed 20 • When connecti ng with the USB bus power cable: Use the USB bus power cable and USB cable . 1. Connect the USB bus power cable. Remove the adhesive label cove ring the USB and power connectors Connect to the ScanSnap’ s power connector and your computer . 2. Connect the USB cable. Connect the USB cable to bot ...
-
Fujitsu S300M - page 22
21 ■ T urning the ScanSnap ON 1. Open the Paper chute of the ScanSnap. 2. The ScanSnap is turned ON. ⇒ The Power indicator starts blinking, and becomes solid. Then, the ScanSnap is recognized as new hardwa re by your computer . ATTENTION • Be sure to use the supplied USB bus power cable. • Be sure to use the supp lied USB cable. The operati ...
-
Fujitsu S300M - page 23
ScanSnap S300M Getting Start ed 22 3. The connection of the ScanSnap is complete. HINT The ScanSnap Manager icon in the Dock menu is d isplayed as . The displayed icon in the Dock menu varies depending on the cab le connection you made. • Power cable connection: • USB bus power cable connection: This guide uses examples for power cable connecti ...
-
Fujitsu S300M - page 24
23 Chapter 3 How to Use the ScanSnap This chapter describes basi c operation of the ScanSnap. 3.1 Scanning Document s With the ScanSnap, you can turn paper office documents on your desk into digital files, save them, attach them to e- mail, and prin t them just by pressing a sin gle button. The scanned image can be viewed on the sc reen using the a ...
-
Fujitsu S300M - page 25
ScanSnap S300M Getting Start ed 24 2. Change the scanning settings on th e "ScanSnap Manager - Scan and Save Settings" window . Y ou can update your last-saved settings for scanning when [Settings] is se lected. There are six tabs us ed to configure the scan options at maximum (The nu mber of tabs displayed and items that can be configure ...
-
Fujitsu S300M - page 26
25 3. Press the [SCAN] button. ⇒ Scanning is started. ⇒ The ScanSnap Quick Menu appears after scanning. 4. Select a desirable action in the ScanS n ap Quick Menu for the image of the scanned document. HINT The scanning me thod above is for the case where the "Quick Menu Mode" is applied. If you switch to the "Pro file Mode," ...
-
Fujitsu S300M - page 27
ScanSnap S300M Getting Start ed 26 3.4 Scanning Business Cards using Cardiris 1. Select "Cardiris" in the "Se lect a Profile" window which pops up when clicking the ScanSnap Manager icon . 2. Load the document o nto the Scan Snap and press the [SCAN] button. - Load the business cards face down. - When scanning more than one busi ...
-
Fujitsu S300M - page 28
27 3. Check the image data of the scanned business cards in the Cardiris window . The images of each bus iness ca rd are displayed on the right. A list of already scanned busines s cards is displayed on the left. Under the image, the recognize d characters are displayed. 4. Should there be any recognition errors, correct the data manually . Correct ...
-
Fujitsu S300M - page 29
ScanSnap S300M Getting Start ed 28 6. On the "Format:" pop-up m enu, select "Address Book." 7. Click the [OK] button. 8. Click the [Send] button or select [P rocess] - [Sen d] on the menu bar . ⇒ The Address Book window appears, and th e recognized characte rs of all scanned business cards in the card toolbar are registered in ...
-
Fujitsu S300M - page 30
29 Chapter 4 T roubleshooting This chapter describes common problems durin g the usage of the ScanSnap and how to remedy them. 4.1 T roubleshooting Checklist Before you ask for repair serv ice, please check the following items. If you cannot so lve the problem even after checking the following items, contact the store where you purchased the ScanSn ...
-
Fujitsu S300M - page 31
ScanSnap S300M Getting Start ed 30 Scanning does not start. Is ScanSnap Manager for the ScanSnap S300M inst alled in your computer? Install ScanS nap Manager for the ScanSnap S300M. (See "Inst alling the Supplied Software" (p age 15).) Is the USB cable correctly connected? Connect the USB cable correctly . When using a hub, check the hub& ...
-
Fujitsu S300M - page 32
31 The ScanSnap is not recognized, though ScanSnap Manager is installed. Did you connect the ScanSnap to your computer before installing ScanS nap Manager? Have the "ScanSnap Manager" started? If your operating syst em is Mac OS X v10.2, in the "System Preferences" window , select "Login Items" - "Add" to add ...
-
Fujitsu S300M - page 33
ScanSnap S300M Getting Start ed 32 4.2 Clearing Paper Jams 1. Remove the document on the paper chute. 2. Open the ADF while pulling the Cover open lever . 3. Remove the jammed document. 4. Close the ADF . ⇒ Y ou should hear the ADF click when it returns to its original position. Click! ...
-
Fujitsu S300M - page 34
33 Chapter 5 Daily Care This chapter descri bes how to clean the Sca nSnap. 5.1 Cleaning Materials *1) It may take long before the cleaner va porizes if a large quantity is used. When cleaning the ScanSnap parts, dampen a cloth with modest quantities of the cleane r. In addition, wipe off the cleaner completely with a soft lint -free cloth to leave ...
-
Fujitsu S300M - page 35
ScanSnap S300M Getting Start ed 34 5.3 Cleaning Inside of the ScanSnap Clean inside of the ScanSnap with a cloth moistened with Cleaner F1. In an alternating succession of scan ning documents, the accumulated paper-powder and dust insi de the ScanS nap causes a scanning error. As a guideline, clean the ADF every 200 sheets of documents. Note that t ...
-
Fujitsu S300M - page 36
35 Chapter 6 Consumables This chapter describes how to replace and pu rchase consumables a nd regular replacement parts. The following table lists the part number s of consumables and shows rough guidelines for replacing these parts. These replacement cycles are rough guideli nes when A4/Letter wood-free paper 64 g/ m 2 (17 lb) is used. T he actual ...
-
Fujitsu S300M - page 37
ScanSnap S300M Getting Start ed 36 Use only the consumables specified by PF U LIMITED. HINT Use the following procedure to check the target values for repla cement and usage information of consum ables. 1. Click and hold the ScanSnap Manager icon in the Dock menu. 2. Click [Check consumable supplies] on the menu. ⇒ The "ScanS nap Man ager - ...
-
Fujitsu S300M - page 38
37 The contents of this manual are subject to change without notice. Th is manual may not be reproduced, adapted or translated without prior written perm ission. READ THIS ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF THIS PRODUCT IS NOT USED CORRECTLY , UNEXPECTED IN JURY MAY BE CAUSED TO USERS OR BYSTANDERS. While all efforts have been ma ...
У вас вопрос, касающийся Fujitsu S300M?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Fujitsu S300M, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Fujitsu S300M со всей вероятностью он захочет поделиться методом ее решения.