-
Renesas H8/3644 Series - page 1
H8/3644 Series TFP-80C User System Interface Cable (HS3644ECN61H) for E6000 Emulator User’s Manual Rev. 4.0 4/1/03 Renesas Technology Corp. HS3644ECN61HE(D) ...
-
Renesas H8/3644 Series - page 2
Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property ...
-
Renesas H8/3644 Series - page 3
i Preface Thank you for purchasing this user system interface cable (HS3644ECN61H) for the Renesas’s original mi crocomputer H8/300L series. The HS3644ECN61H is a user system interface cab le that connects an H8/300L series E6000 emulator (HS3L08EPI60H; hereinafter referred to as the emulator) to the IC socket for a TFP-80C package for the H8/364 ...
-
Renesas H8/3644 Series - page 4
ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interf ace Cable to Em ulat or Station ......................................... 3 2.2 Connecti ...
-
Renesas H8/3644 Series - page 5
Section 1 Configuration CAUTION Use an IC149-080-058-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-80C package IC socket on the user system. Figure 1 shows the configuration of the HS3644E CN61H user system interface cable for the TFP-80C package. Figure 1 HS3644ECN61H User System Interface Cable 1 ...
-
Renesas H8/3644 Series - page 6
2 Table 1 lists t he HS3644ECN61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS3644ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the TFP-80C package 4 Socket cover 1 For installing an TFP-80C-packaged MCU 5 Screws (M2.6 x 12 mm) 4 For fastenin ...
-
Renesas H8/3644 Series - page 7
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system a ...
-
Renesas H8/3644 Series - page 8
Figure 2 Connecting User System Int erface Cable to Emulator Station 4 ...
-
Renesas H8/3644 Series - page 9
2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pi n 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the ...
-
Renesas H8/3644 Series - page 10
6 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an TFP-80C package on the user system wi th pin 1 on the user system interface cable head, and inse rt the user system interface cable head into the IC socket on the user system, as shown i n figure 3. 2.2.4 Fastening Cable Head CAUTI ...
-
Renesas H8/3644 Series - page 11
Fasten the user system interface cable head to the IC socket fo r an TFP-80C package on the user system wit h the four screws (M2.6 x 12 mm ; with four flat washers) provided. Each screw should be tightened a little at a time, alternating between screws on opposing corners. Take special care, such as manually securing the IC so cket soldered area, ...
-
Renesas H8/3644 Series - page 12
2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Unfastening jig Push the unfastening jig Removing User system Figure 4 Fastening Cable Body 8 ...
-
Renesas H8/3644 Series - page 13
2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an TFP-80C package (IC149-080-058-B51: m anufactured by YAM AICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 5 are somewh at different from those of the actual chip ...
-
Renesas H8/3644 Series - page 14
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 6. Figure 6 Dimensions for User System Interface Cable Head 10 ...
-
Renesas H8/3644 Series - page 15
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 7. Figure 7 Resulting Dimensions after Connecting User System Interface Cable 11 ...
-
Renesas H8/3644 Series - page 16
12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes ...
-
Renesas H8/3644 Series - page 17
MCU Pin 1 IC socket (IC149-080-058-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Screws (M2.6 x 8 mm) with flat washers Socket cover Figure 8 Installing MCU to User System 13 ...
-
Renesas H8/3644 Series - page 18
14 Section 4 Verifying Operation 1. When using the H8/300L series E6000 emulat or (HS3L08EPI60H), turn on the emulat or according to the procedures described in the H8/300L Series E6000 Em ulator User' s Manual (HS3008EPI60HE). 2. Verify the user system interface cable c onnections by accessing ports and checking the bus states of the pins. If ...
-
Renesas H8/3644 Series - page 19
Figure 9 shows the system clock oscillator on the us er system interface cable and the subclock input specifications. 15 R2 270 R1 1 M HCU04 HCU04 To E6000 emulator OSC1 OSC2 System clock oscillator Ω Ω 0.8 Vcc 55 ns max. 55 ns max. 0.8 Vcc 0.3 Vcc 0 V Vcc Vcc: User System Vcc (3.0 V to 5.0 V) 0.3 Vcc Subclock input specifications Figure 9 Syst ...
-
Renesas H8/3644 Series - page 20
4. The P60 to P67 pins are CMOS large-current port s in the MCU, but in the em ulator, they are normal ports. However, when this user system interface cable is used, a large current of I OL = 10.0 mA (m ax.) can be output from the ports by changi ng the P5 jumper setting. Note that when the jumper is set t o the large-current m ode, the P60 to P67 ...
-
Renesas H8/3644 Series - page 21
Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU. 3. This user system interface cable is specific ...
-
Renesas H8/3644 Series - page 22
6. The flash memory functi ons of the H8/3644 series are not supported by the emulator. Therefore, do not apply 12 V to Vp p/P90 and TEST pins. If 12 V is ap plied, the emulator will detect it as the test mode. The Vpp/ P90 and TEST pins have circuits for protection against 12-v applicati on, as shown in figure 12. To E6000 emulator station To E600 ...
У вас вопрос, касающийся Renesas H8/3644 Series?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Renesas H8/3644 Series, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Renesas H8/3644 Series со всей вероятностью он захочет поделиться методом ее решения.