-
Ryobi HP1830M - page 1
This new cordless hammer drill has been engineered and manuf actured to Ryobi’ s high standard f or dependability , ease of operation, and operator saf ety . When properly cared f or , the drill-driver will giv e you y ears of rugged, trouble-free perf or man ce. W ARNING: T o reduce the risk of injur y , the user m ust read and understand the op ...
-
Ryobi HP1830M - page 2
Page 2 ■ ■ ■ ■ ■ Introduction ................................................................................................................................................................... 2 ■ ■ ■ ■ ■ General Saf ety Rules ...................................................................................................... ...
-
Ryobi HP1830M - page 3
Page 3 GENERAL SAFETY RULES W ARNING Read and understand all instructions. F ailure to follo w all instructions listed below , ma y result in electric shock, fire and/or serious personal injur y . SA VE THESE INSTRUCTIONS WORK AREA ■ Keep your work area clean and well lit . Cluttered benches and dark areas invite accidents. ■ Do not operate pow ...
-
Ryobi HP1830M - page 4
Page 4 SPECIFIC SAFETY RULES ■ ■ ■ ■ ■ Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator . ADDITIONAL RULES FOR SAFE OPERA TION ■ Know your power too ...
-
Ryobi HP1830M - page 5
Page 5 IMPOR T ANT SAFETY INSTR UCTIONS FOR CHARGER W ARNING: Read and understand all instructions. Failure to fol- low all instructions listed below, may result in electric shock, fire and/or serious personal injury. ■ Never use a battery that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose ...
-
Ryobi HP1830M - page 6
Page 6 SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention ...
-
Ryobi HP1830M - page 7
Page 7 SPECIFICA TIONS Chuck .......................................................................................................................... ................... 1/2 in. (13 mm) Keyless Motor .......................................................................................................................... ......................... ...
-
Ryobi HP1830M - page 8
Page 8 KNOW YOUR HAMMER DRILL See Figure 1. Before using this product, familiarize yourself with all operating features and safety requirements. However, do not let familiarity with the tool make you careless. KEYLESS CHUCK This hammer drill has a heavy-duty ke yless chuck that allo ws you to hand tighten or release drill bit in the chuck jaws. SWI ...
-
Ryobi HP1830M - page 9
Page 9 20 24 FEA TURES Fig. 1 KEYLESS CHUCK BIT ST ORAGE AREA SWITCH TRIGGER BA TTER Y P ACK DIRECTION OF ROT A TION SELECTOR THREE SPEED GEAR TRAIN (LO-HI-SUPER-HI) ...
-
Ryobi HP1830M - page 10
Page 10 20 24 20 24 ADJUSTMENTS W ARNING: The hammer drill should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury. ADJUSTING THE AUXILIARY HANDLE ASSEMBLY S ...
-
Ryobi HP1830M - page 11
Page 11 20 24 ADJUSTMENTS ADJUSTING THE TORQUE See Figure 4. The hammer drill is equipped with an adjustable torque clutch for driving different types of screws into different materials. Adjust the torque as necessary. We recommend that you use carbide-tipped bits and select hammer mode when drilling in hard materials such as brick, tile, concrete, ...
-
Ryobi HP1830M - page 12
Page 12 24 ADJUSTMENTS CHANGING THE BIT ROTATION See Figure 5. The direction of the chuck is controlled by the rotation selector located above the trigger switch. Follow these steps to change the bit rotation. ■ For forward rotation : Move the rotation selector to the left. ■ For reverse rotation : Move the rotation selector to the right. Note: ...
-
Ryobi HP1830M - page 13
Page 13 OPERA TION W ARNING: Exercise caution when using this tool. Careless actions, for even a fraction of a second, can result in serious personal injury. CHARGING YOUR DRILL-DRIVER The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it prior to use. Note: Batteries ...
-
Ryobi HP1830M - page 14
Page 14 20 24 OPERA TION TURNING ON/OFF THE HAMMER DRILL See Figure 10. Follow these steps to turn on/off the hammer drill. ■ Turn on the hammer drill : Depress the trigger switch. ■ Turn off the hammer drill : Release the trigger switch. VARIABLE SPEED See Figure 10. Your drill has a variable speed feature in the switch. The switch delivers hi ...
-
Ryobi HP1830M - page 15
Page 15 20 24 OPERA TION THREE SPEED GEAR TRAIN See Figure 11. The hammer drill has a two-speed gear train that provides a high speed of approximately 1,400/min and a low speed of approximately 400/min (stated speeds are with the trigger switch in the “Full-on” position). Follow these steps to adjust the speed. ■ For super high speed : Slide ...
-
Ryobi HP1830M - page 16
Page 16 OPERA TION BIT STORAGE See Figure 14. When not in use, the bit provided with this drill can be placed in the storage area located on the base of the drill. ELECTRIC BRAKE This drill has an electric brake. When the trigger switch is released, the chuck stops turning. When the brake is functioning properly , spar ks will be visib le through t ...
-
Ryobi HP1830M - page 17
Page 17 OPERA TION W ARNING: Always wear safety goggles or safety glasses with side shields when operating tool. Failure to do so could result in dust, shavings, or loose particles being thrown into your eyes, resulting in possible serious injury. DRILLING See Figure 15. The material to be drilled should be secured in a vise or with clamps to keep ...
-
Ryobi HP1830M - page 18
Page 18 24 MAINTENANCE REMOVING THE CHUCK See Figures 16, 17, and 18. Follow these steps to remove the chuck. ■ Lock the trigger switch by placing the rotation selec- tor in the center position. ■ Insert a 5/16 inch or larger hex key wrench into the chuck of the drill and tighten the chuck jaws securely. ■ Tap the hex key wrench sharply with ...
-
Ryobi HP1830M - page 19
Page 19 MAINTENANCE W ARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts can create a hazard or cause product damage. A void using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use a clean cloth to remove ...
-
Ryobi HP1830M - page 20
R Y OBI TECHNOLOGIES, INC. 1428 P earman Dair y Road Anderson, SC 29625 P ost Office Box 1207, Anderson, SC 29622-1207 Phone 1-800-525-2579 www .ryobitools.com 983000-339 6-03 • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure ...
У вас вопрос, касающийся Ryobi HP1830M?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Ryobi HP1830M, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Ryobi HP1830M со всей вероятностью он захочет поделиться методом ее решения.