-
Fisher & Paykel DD605 - page 1
DishDra wer Installation instructions NZ A U GB IE DD605 and DS605 models ...
-
Fisher & Paykel DD605 - page 2
Safety and warnings Impor tant safety precautions! Installation of this DishDrawer® requires basic mechanic al and electrical skills. Be sure to leave these Instructions with the Customer . Installation must comply with your loc al building and electricity regulations. At the completion of the DishDrawer® installation, the Installer m ust per for ...
-
Fisher & Paykel DD605 - page 3
1 Contents DOUBLE MODELS Product and cabinetry dimensions 2 Installation Cavity prepar ation 4 Route the hoses and mov e into the cavity 5 Removing the tub and levelling the pr oduct 6 Securing the product and refitting the tub 7 Plumbing and drainage - OPTION 1 8 Plumbing and drainage - OPTION 1 (connection) 9 Plumbing and drainage - OPTION 2 10 P ...
-
Fisher & Paykel DD605 - page 4
2 Pr oduc t dimensions O B C E D F G H J N P Pr oduct dimensions (mm) Pre nished L CD DD605 Pre nished Flat door DD605 Integrated DD605 A overall height* of product 819.5 - 879.5 819.5 - 879.5 819.5 - 879.5 B overall width of product 595 595 595 C overall depth of product (excl. curvature/handle) 570 570 570 D depth of drawer (open) (excl. cu ...
-
Fisher & Paykel DD605 - page 5
3 Cabinetry dimensions A B C D Cabinetry dimensions (mm) Pre nished LC D DD605 Pre nished Flat door DD605 Integrated DD605 A inside height of cavity 820 - 882.5 820 - 882.5 820 - 882.5 B inside width of cavity 600 600 600 C inside depth of cavity (inside) 580 580 580 D height of adjacent cabinetry 720 720 720 E height of kickstrip 70 - 120 70 ...
-
Fisher & Paykel DD605 - page 6
4 Note: Services can be located either side of DishDr awer®. Ca vity preparation Parts supplied These marks indicate mounting tab screw locations Pref erred position. If adequate clearance, services hole can be higher to clear toe kick space. If hole is higher , ensure drain hose(s) are r outed straight into the waste connection. Clamp (1) Wire cl ...
-
Fisher & Paykel DD605 - page 7
5 Route the hoses and mov e into the ca vity DOUBLE MODELS 2 1 1 1 2 3 3 optional 1 b 2 optional 1 a Tie together to a void kink ing If top two tabs are being used, ensure they’r e securely fitted before sliding pr oduct into cavity . Ensure hoses and cord are not kinked or twisted. Loosen feet first, but do not fully extend until product is in c ...
-
Fisher & Paykel DD605 - page 8
6 Removing the tub and lev elling the product 30 mm x 4 1 2 3 4 5 5 1 2 3 4 5 3 DOUBLE MODELS 4 Ensure the tub is remov ed and then rotated counter-clockwise to prevent kinked hoses. Ensure product is level. U sing the most appropriate length Hexagonal socket supplied, and a screw driver , fully extend levelling feet up to r equired distance. Hexag ...
-
Fisher & Paykel DD605 - page 9
7 Securing the product and re tting the tub DOUBLE MODELS A 1 2 4 5 4 3 C C BB A 5 6 optional The mounting tabs are in pairs, one on each side of the product. At least two sets of tab pairs must be used. A and B tab pairs OR B and C tab pairs or all three pairs. Ensure the sound insulation is repositioned correctly . Before r efitting the tub, e ...
-
Fisher & Paykel DD605 - page 10
8 DishDraw er® and Standpipe Ø 38 mm W ater Pr essure Max Min W ater softener models 1 MPa (145 psi) 0.1 MP a (14.5 psi) Other models 1 MP a (145 psi) 0.03 MPa (4.3 psi) Drains will need to be separated to satisfy Kosher requir ements. W e suggest you confirm acceptability with your local Rabbi in respect to Kosher installations. Plumbing and dra ...
-
Fisher & Paykel DD605 - page 11
9 Plumbing and drainage - OPTION 1 (c onnec tion) DOUBLE MODELS 2 750- 882.5 mm 38 mm max. 120 mm 4 3 2 1 1 180 o 7 If space is limited for fixing, push hose through drain hose support to required height DishDraw er® and Standpipe Ø 38 mm 8 Fit supplied washer ...
-
Fisher & Paykel DD605 - page 12
10 DishDraw er® using sink trap with drain hose joiner Plumbing and drainage - OPTION 2 DOUBLE MODELS 750 - 882.5 mm Wa st e Va lv e Wa te r supply (COLD) Supplied drain hose joiner min. R200 mm HIGHL OOP min. 150 mm ...
-
Fisher & Paykel DD605 - page 13
11 Plumbing and drainage - OPTION 2 (c onnec tion) DOUBLE MODELS 2 3 750- 882.5 mm 1 4 3 2 1 180 o DishDraw er® using sink trap with drain hose joiner If space is limited for fixing, push hose through drain hose support to required height 7 8 Fit supplied washer Ensure hoses are rout ed straight to joiner . Remove excess hose material if necessary ...
-
Fisher & Paykel DD605 - page 14
12 F itting the toekick 1 2 3 4 5 6 7 8 9 10 19 9 10 DOUBLE MODELS Impor tant! D o not overtighten screw . ...
-
Fisher & Paykel DD605 - page 15
13 ...
-
Fisher & Paykel DD605 - page 16
14 Pr oduc t dimensions A B C E D F G H J K L Pr oduct dimensions (mm) Pre nished L CD DS605 Pre nished Flat door DS605 Integrated DS605 A overall height* of product 409 409 409 B overall width of product 595 595 595 C overall depth of product (excl. curvature/handle) 570 570 570** D depth of drawer (open) (excl. curvature/handle) 520 520 520 ...
-
Fisher & Paykel DD605 - page 17
15 Cabinetry dimensions A B C D Cabinetry dimensions (mm) Pre nished LC D DS605 Pre nished Flat door DS605 Integrated DS605 A inside height of cavity 412 412 412 B inside width of cavity 600 600 600 C inside depth of cavity (inside) 580 580 580 D clearance below benchtop Minimum 3* Minimum 3* Minimum 3* * Clearance is measured from the unders ...
-
Fisher & Paykel DD605 - page 18
16 Ca vity preparation Cavit y These marks indicate mounting tab screw locations Note: T o align drawer front to adjacent cabinetry , the product to counter top clearance can be increased to 3 mm. Pref erred position. If adequate clearance, services hole can be higher . If hole is higher , ensure drain hose(s) are r outed straight into the waste co ...
-
Fisher & Paykel DD605 - page 19
17 SINGLE MODELS Route the hoses and mov e into the cavity 1 1 1 2 2 2 Tie together to a void kink ing 1 b 2 1 a Ensure hoses and cord are not kinked or twisted. ...
-
Fisher & Paykel DD605 - page 20
18 Removing the tub and securing the pr oduc t 2 30 mm 1 5 5 3 4 SINGLE MODELS 3 4 Ensure the tub is remov ed and then rotated counter-clockwise to prevent kinked hoses. The mounting tabs are in pairs, one on each side of the product. Ensure the sound insulation is repositioned correctly . ...
-
Fisher & Paykel DD605 - page 21
19 Re tting the tub 2 1 4 5 4 3 SINGLE MODELS 5 Before r efitting the tub, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward. Ensure the tub clips on both sides are reset. Ensure the tub is now rotated clockwise back. ...
-
Fisher & Paykel DD605 - page 22
20 DishDraw er® and Standpipe Ø 38 mm W ater Pr essure Max Min W ater softener models 1 MPa (145 psi) 0.1 MP a (14.5 psi) Other models 1 MP a (145 psi) 0.03 MPa (4.3 psi) Plumbing and drainage - OPTION 1 750 - 882.5 mm Wa st e Wa st e Va lv e Wa te r supply (C OLD) W aste disposal (optional) Do not connect to DishDrawer® min. R200 mm SINGLE MODE ...
-
Fisher & Paykel DD605 - page 23
21 Plumbing and drainage - OPTION 1 (c onnec tion) 2 1 750- 882.5 mm 38 mm max. 120 mm 4 3 2 1 180 o DishDraw er® and Standpipe Ø 38 mm SINGLE MODELS If space is limited for fixing, push hose through drain hose support to required height 7 8 Fit supplied washer ...
-
Fisher & Paykel DD605 - page 24
22 Plumbing and drainage - OPTION 2 DishDraw er® using sink trap with drain hose joiner 750 - 882.5 mm Va lv e Wa st e Wa te r supply (COLD) Supplied drain hose joiner min. R200 mm SINGLE MODELS HIGHL OOP min. 150 mm ...
-
Fisher & Paykel DD605 - page 25
23 Plumbing and drainage - OPTION 2 (c onnec tion) 2 3 750- 882.5 mm 38 mm max. 120 mm 1 4 3 2 1 180 o DishDraw er® using sink trap with drain hose joiner SINGLE MODELS If space is limited for fixing, push hose through drain hose support to required height 7 8 Fit supplied washer ...
-
Fisher & Paykel DD605 - page 26
24 F inal checklist Check all parts are installed. Ensure product is level, secur ely fastened to the cabinetry and opens and closes freely . The DishDrawer® must be free t o fully close with no resistance from the cabinetry . Ensure inlet hose to water supply has rubber washer fitted and is tight ened a fur ther half turn after seal contact. Ensu ...
-
Fisher & Paykel DD605 - page 27
...
-
Fisher & Paykel DD605 - page 28
Copyright © F isher & Pa ykel 2007. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at an y time. Y ou should therefor e check with your Dealer to ensure this booklet corr ...
У вас вопрос, касающийся Fisher & Paykel DD605?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Fisher & Paykel DD605, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Fisher & Paykel DD605 со всей вероятностью он захочет поделиться методом ее решения.