-
Graco Inc. 313385B - page 1
313385B Repair and P ar ts GTX ™ 2000 EX - For W ater -Based Materials Only- Model: 257030 Spray er with Graco T rigger Gu n 120 psi (8.27 bar) Maximu m Working Air Pressure 120 psi (8.27 bar ) Maximum W orking Fluid Pressure Important Safety Instructions Read all warnings and instructions in this manual. Sav e these instr uctions. Related Man ua ...
-
Graco Inc. 313385B - page 2
2 313385B Wa r n i n g s The f ollowing wa r nings are for t he setup, use , grounding, mainten ance, and repair of this equipment . The exclama- tion point symbol alerts you to a gener al warning and the hazard symbol ref ers to procedu re-specific risk. Refer back to these wa r nings. Additional, product- specific warnings ma y be fou nd througho ...
-
Graco Inc. 313385B - page 3
313385B 3 PLASTIC P ARTS CLEANING SOL VENT H AZARD Use only compatib le water-based solv ents to clean plastic structural o r pressure-containing par ts. Man y solve nts can degrade plastic part s and cause them to f ail, which could cause serious injur y or proper ty damage. See Te c h n i c a l D a t a in this and all other equipme nt instruction ...
-
Graco Inc. 313385B - page 4
Component Identification 4 313385B Component Identification ti13066a L A J H G B E F D C K ...
-
Graco Inc. 313385B - page 5
Component Identi fication 313385B 5 Component Identification List * Ref erence numbers used in gun illustrations coinci de with ref erence numbers sh o wn in gun manual 310616 A Nozzle Storage B Hopper C Hopper Quic k Connect D Diaphragm Pu mp E Material Outlet Option 1 F Material Outlet Option 2 G Gun Air Outlet Quic k Connect H Material (Pump) Ai ...
-
Graco Inc. 313385B - page 6
Preparation 6 313385B Preparation Pressure Relief 1. Disconnect air inlet. 2. Open gun air valv e (23). 3. T rigger gun, and spra y material back into hopper . Hopper Remo val and Installation The hopper (G) can be remo ved from th e car t f or clean- ing and servicing equipment. NO TE: Bef ore removing hopper , allow un it to cool down and/or remo ...
-
Graco Inc. 313385B - page 7
Pump Removal and Installation 313385B 7 Pump Remo v al and Installation Pump Remo val 1. Relie ve Pressure, page 6. 2. Remove hopper , page 6. 3. Disconnect air lines. 4. Disconnect exhaust tube. 5. Remove f our bolts holding pump to car t. 6. Lift pump straight up o ff car t. Pump Installation 1. Lower p ump on car t. 2. Replace four bolt s holdin ...
-
Graco Inc. 313385B - page 8
Troubleshooting 8 313385B T roub leshooting Bef ore perf or ming any T roubleshoo ting procedures, f ollow Pressur e Relief procedure on pa ge 6. PROBLEM CA USE SOLUTION No material output from pump Not enough air pressure to pump Shut off air at the gun, and increase air pressure to the pump to maximum. T ur n regulator clockwise to increase . Mat ...
-
Graco Inc. 313385B - page 9
Troubleshooting 313385B 9 P atter n too fine or too much o verspra y Material too thin Thick en material. Mater ial must be mix ed thoroughly to a consistency that immediately folds bac k in as you dra w your finger through the surf ace of the material . Air pressure at gun too high Decrease air to gun at gun fitting and/or regulator . Fluid delive ...
-
Graco Inc. 313385B - page 10
Parts Drawing 10 313385B Pa r t s D r a w i n g 29 9 8 44 3 36 33 43 32 58 40 2 39 42 38 28 31 6 4 5 72 1 30 7 ti3953c ...
-
Graco Inc. 313385B - page 11
Parts Drawing 313385B 11 Pa r t s D r a w i n g A B A B 22 18 22 17 24 15 14 13 27 10 16 19 18 22 26 15 17 26 10 21 16 23 21 20 25 11 65 70 13 67 66 12 71 ti3954c 75 76 68 69 ...
-
Graco Inc. 313385B - page 12
Parts Drawing 12 313385B Pa r t s D r a w i n g 35 34 45 38 41 ti3955a ti3956a ...
-
Graco Inc. 313385B - page 13
Parts Drawing 313385B 13 P ar ts List Ref. P art Description Qty . 1 15C878 FRAME, te xture, b lue 1 2 801504 FOO T , r ubber 2 3 15C843 HOPPER, te xture , gas 1 4 116478 WHEEL, pneumatic 2 5 101242 RING, retaining, ext. 2 6 111841 W ASHER, plain 5/8 2 7 246887 PUMP , diaphra gm, 1040, te xture 1 8 15C759 COUPLING, pump 1 9 15D985 FITTING, adap ter ...
-
Graco Inc. 313385B - page 14
Pump Parts Drawing 14 313385B Pump P ar ts Dra wing *402 15 12 23 113 106 202* 103 19 11 20 22 25 104 401* 105 108* 107 101 301* 202* 201 202* 102 113 106 113 301* 202* 201* 11 3 2 5 8 16 106 113 16 3 4† 9† 7† 6† 18† 17† 10† 17† 10† ▲ 110 ti12959a ...
-
Graco Inc. 313385B - page 15
Pump Parts Drawing 313385B 15 Pump P ar ts List Ref. P art Description Qty . 1 188838 HOUSING, ce nter , aluminum 1 2 188854 CO VER, air v alve , aluminum 1 3 116344 SCREW , mach, he x flange hd; M5 X 0.8; 12 mm (0.47 in.) 9 4 188618 GASKET , molded Santoprene 1 5 188855 CARRIA GE, aluminum 1 6† 108730 O-RING, nitrile 1 7† 188616 BLOCK, air val ...
-
Graco Inc. 313385B - page 16
Technica l Data 16 313385B T echnical Data Maximum air w or king pressure . . . . . . . . . . . . 120 psi (8.27 bar) Maximum working fluid pressure . . . . . . . . . . 120 psi (8.27 bar) Compressor (not supplied) AIr Delivery . . . . . . . . . . . . . . . . . . . . . . . 12 cfm @ 100 psi (340 lpm @ 6.9 bar) Hopper capacity Maximum . . . . . . . . . ...
-
Graco Inc. 313385B - page 17
Notes 313385B 17 Notes ...
-
Graco Inc. 313385B - page 18
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 313385 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 14 ...
У вас вопрос, касающийся Graco Inc. 313385B?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Graco Inc. 313385B, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Graco Inc. 313385B со всей вероятностью он захочет поделиться методом ее решения.