-
CDA HVC70SS - page 1
VITROCERAMIC COOKING HOBS INSTRUCTIONS FOR USE - ADVICE FOR THE INST ALLER Before operating this cooking hob, please read these instructions carefully KEEP IN A SAFE PLACE ...
-
CDA HVC70SS - page 2
2 Dear Customer, Thank you for having purchased and given your preference to our product. The safety precautions and recommendations reported below are for your own safety and that of others. They will also provide a means by which to make full use of the features offered by your appliance. Please preserve this booklet carefully. It may be useful i ...
-
CDA HVC70SS - page 3
3 BEFORE USING FOR THE FIRST TIME • Read the instructions carefully before installing and using the appliance • After unpacking the appliance, make sure it is not damaged. In case of doubt, do not use the appliance and contact your supplier or a qualified engineer. • Remove all packaging and do not leave the packing material (plastic bags, po ...
-
CDA HVC70SS - page 4
FEA TURES 4 1 1 1 1 2 3 4 1 5 6 7 9 10 8 60 cm models Electrical insulation Class I COOKING POINTS (Fig. 1.1) 1. Hi-light cooking zone Ø 140 mm - 1200 W 2. Hi-light cooking zone Ø 210 mm - 2300 W 3. Double hi-light cooking zone Ø 210/120 mm - 2200/750 W 4. Hi-light cooking zone Ø 140 mm - 1200 W CONTROLS DESCRIPTION 5. Left front zone (1) contr ...
-
CDA HVC70SS - page 5
5 2 3 4 1 5 6 7 9 10 8 80 cm models Electrical insulation Class I COOKING POINTS (Fig. 1.3) 1. Hi-light cooking zone Ø 140 mm - 1200 W 2. Oval double hi-light cooking zone Ø 180 x 260 mm - 800/2200 W 3. Hi-light cooking zone Ø 140 mm - 1200 W 4. Double hi-light cooking zone Ø 210/120 mm - 2200/750 W CONTROLS DESCRIPTION 5. Left front zone (1) c ...
-
CDA HVC70SS - page 6
6 2 4 5 1 6 7 8 9 11 12 10 3 90 cm models Electrical insulation Class I COOKING POINTS (Fig. 1.4) 1. Hi-light cooking zone Ø 180 mm - 1800 W 2. Hi-light cooking zone Ø 140 mm - 1200 W 3. Oval double hi-light cooking zone Ø 180 x 260 mm - 800/2200 W 4. Double hi-light cooking zone Ø 210/120 mm - 2200/750 W 5. Hi-light cooking zone Ø 140 mm - 12 ...
-
CDA HVC70SS - page 7
7 HI-LIGHT RADIANT ZONES (Fig. 2.1) The heating element is formed of a coil of resistant material which reaches the working temperature quickly. These zones are controlled by a contin- uous energy regulator switch (figs. 2.2a - 2.2b). The heat intensity can be regulated con- tinuously from “0” to “12” (max). Check that the hob is clean and ...
-
CDA HVC70SS - page 8
8 HI-LIGHT DOUBLE ZONE and HI-LIGHT OV AL ZONES The heating element is formed of a 2 coils of resistant material which reaches the work- ing temperature quickly. These zones are controlled by a continuous energy regulator switch (figs. 2.3a - 2.3b). The heat intensity can be regulated continuously from “0” to “12” (max). Check that the hob ...
-
CDA HVC70SS - page 9
9 After a short period of use, experience will teach you which setting is the right one for your needs. CO0KING HINTS Fig. 2.5 Heating Cooking Roasting-frying Cooking zone knob setting 1 2 3 4 5 6 7 8 9 10 11 12 TYPE OF COOKING Switched OFF For melting operations (butter, chocolate). To maintain food hot and to heat small quantities of liquid (sauc ...
-
CDA HVC70SS - page 10
10 RESIDUAL HEA T INDICA TORS The hob also features 4 or 5 warning lamps which are wired to the corresponding plate. When the temperature of a cooking plate is over 60°C, the relevant warning lamp is also lit- up to warn of heat on the surface of the hob. These lamps also stay on after the cooking plates have been switched off to shown that the ho ...
-
CDA HVC70SS - page 11
11 SAFETY HINTS • Before you switch the hob on, make sure you know which knob controls the required cooking zone. We advise you to set the pan over the cooking zone before switching it on. • Do not use pots and pans with rough bases (pay attention to cookware made of cast-iron). Rough bases can damage the glass surface of the hob (scratches). ? ...
-
CDA HVC70SS - page 12
12 CLEANING THE CERAMIC HOB Before you begin cleaning make sure that the hob is switched off. • Remove spillages and other types of incrustations. • Dust or food particles can be removed with a damp cloth. • If you use a detergent, please make sure that it is not abrasive or scouring. Abrasive or scouring powders can damage the glass surface ...
-
CDA HVC70SS - page 13
13 ADVICE FOR THE INST ALLER ...
-
CDA HVC70SS - page 14
14 INST ALLA TION 3 3 3 3 490 560 590 510 A 490 870 900 510 A 490 740 770 510 A CAUTION: • This appliance shall only be serviced by authorized personnel. • This appliance is to be installed only by an authorised person according to the cur- rent local regulations and in observation of the manufacturer’s instructions. • Incorrect installatio ...
-
CDA HVC70SS - page 15
15 This cooktop can be built into a working surface 30 to 40 mm thick and 600 mm deep. In order to install the ceramic hob into the kitchen fixture, a hole with the dimensions shown in figures 3.1a,b,c has to be made, keeping in consideration the following: • NOTE: A partition should be fitted a minimum of 2 cm below the base of the hob (fig. 3.2 ...
-
CDA HVC70SS - page 16
16 30 mm min. 40 mm max. Fig. 3.4 F ASTENING THE COOKTOP Each cooktop is supplied with a set of tabs and screws to fasten it on units with a work- ing surface from 3 to 4 cm deep. The kit includes 4 tabs A and 4 self-threading screws B (fig. 3.4). • Cut the unit. • Turn the hob upside down and rest the glass side on a cloth. • Spread the seal ...
-
CDA HVC70SS - page 17
17 ELECTRICAL CONNECTION 4 4 4 4 IMPORTANT: Installation must be carried out according to the manufacturer's instructions. Incorrect installation may cause harm and damage to people, ani- mals or property, for which the manufacturer accepts no responsibility. Before carrying out any work on the electrical section of the appliance, it must be d ...
-
CDA HVC70SS - page 18
18 E 1 2 3 4 5 N L 220 - 240 V A B C B Fig. 4.1 Fig. 4.2 • The wires in the mains lead are coloured in accordance with the following code: Green & Yellow = Earth Blue = Neutral Brown = Live. As the colours of the wires in the mains lead for the appliance, may not correspond with the coloured markings identifying the terminals in your spur box ...
-
CDA HVC70SS - page 19
19 CONNECTING THE FEEDER CABLE To connect the feeder cable to the hob it is necessary to carry out the following opera- tions: • Unscrew the screw A of the terminal board at the bottom of the hob (fig. 4.1). • Unlock the 2 clips B and open the cover C . • Unscrew the screw D and open completely the cable clamp E (fig. 4.3) . • Position the ...
-
CDA HVC70SS - page 20
20 for the other countries IMPORTANT: Installation must be carried out according to the manufacturer's instructions. Incorrect installation may cause harm and damage to people, ani- mals or property, for which the manufacturer accepts no responsibility. Before carrying out any work on the electrical section of the appliance, it must be disconn ...
-
CDA HVC70SS - page 21
CONNECTING THE FEEDER CABLE To connect the feeder cable to the hob it is necessary to carry out the following opera- tions: • Unscrew the screw A of the terminal board at the bottom of the hob (fig. 4.4). • Unlock the 2 clips B and open the cover C . • Unscrew the screw D and open completely the cable clamp E (figs. 4.6 - 4.7 - 4.8). • Posi ...
-
CDA HVC70SS - page 22
22 PE 1 2 3 4 5 N (L 2 ) L 1 220 - 240 V PE 1 2 3 4 5 PE 1 2 3 4 5 380 - 415 V 3N 380 - 415 V 2N N L 1 L 2 N L 1 L 3 L 2 Fig. 4.5 220-240 V ~ 1 2 3 5 4 N L2 PE L1 G C FD E Fig. 4.6 1 2 3 5 4 PE N L1 L2 L3 G F D E 380-415 V 3N ~ C 1 2 3 5 4 PE N L1 L2 G FD E 380-415 V 2N ~ C Fig. 4.8 Fig. 4.7 ...
-
CDA HVC70SS - page 23
23 ...
-
CDA HVC70SS - page 24
Cod. 1102836 - ß9 Descriptions and illustrations in this booklet are given as simply indicative. The manufacturer reserves the right, considering the characteristics of the models described here, at any time and without notice, to make eventual necessary modifications for their construction or for commercial needs. ...
У вас вопрос, касающийся CDA HVC70SS?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с CDA HVC70SS, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с CDA HVC70SS со всей вероятностью он захочет поделиться методом ее решения.