-
Pelco ICS210 - page 1
INST ALLA TION ICS210 Series Camclosure ® Integrated Camera System C2491M-D (8/06) ...
-
Pelco ICS210 - page 2
2 C2491M-D (8/06) Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . ...
-
Pelco ICS210 - page 3
C2491M-D (8/06) 3 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC, Class A (black -white, EIA and C ...
-
Pelco ICS210 - page 4
4 C2491M-D (8/06) Description The ICS210 Series Camclosure ® is a wedge style integrated camera system that is quick and easy to install. The system is designed to mount directly to a wall or ceiling, or to a corner with the ICS210- CM corner mount. ICS210 system is shipped fully assembled. System components include a cover , base with camera and ...
-
Pelco ICS210 - page 5
C2491M-D (8/06) 5 Installation PREPARE MOUNTING SURFACE 1. Remove the cover of the ICS210. Use the screwdriver bit that is provided to loosen the three tamperproof screws, and then lift the cover from the base. 2. Remove the camera assembly from the base by removing the Phillips screws on each side of the camera assembly (refer to Figure 2 ). Figur ...
-
Pelco ICS210 - page 6
6 C2491M-D (8/06) 4. Select a fi xed or adjustable mounting pattern (refer to Figure 3 and Figure 4 ). Using the mounting plate as a template, mark the wire feedthrough and fastener hole positions on the mounting surface. Prepare the holes for the installation. Figure 3. Fixed Mounting Pattern Figure 4. Adjustable Mounting Pattern FIXED MOUNTING P ...
-
Pelco ICS210 - page 7
C2491M-D (8/06) 7 INSTALL BASE WITHOUT CONDUIT 1. Pull the power and video wiring for the camera through the mounting surface and then through the wiring hole in the mounting plate. Fasten the mounting plate to the mounting surface with #8 stainless steel screws (not provided) of the appropriate length. Adjustable mounting pattern only : Adjust the ...
-
Pelco ICS210 - page 8
8 C2491M-D (8/06) 3. Using a blunt tool push out the wiring plug in the bottom of the base (refer to Figure 6). Pull the wiring inside the base. Figure 6. Removing the Wiring Plug 4. Insert the hole plug that is supplied into the hole in the base of the Camclosure (refer to Figure 7). Figure 7. Installing the Hole Plug HOLE PLUG ...
-
Pelco ICS210 - page 9
C2491M-D (8/06) 9 5. Pull wiring through the conduit opening (refer to Figure 8): a. Use a 1/16” hex head wrench to loosen the hex head inset screw . b. Use a screwdriver to remove the conduit cover. c. Pull the power wires and video cable through the conduit opening. Figure 8. Removing the Conduit Cover 6. Install a 0.75-inch (1.91 cm) conduit c ...
-
Pelco ICS210 - page 10
10 C2491M-D (8/06) REINSTALL CAMERA MODULE Reinstall the camera module. Refer to Figure 9 . Make sure the top of the camera is oriented properly . On the lens housing, look for the label that says TOP . Figure 9. Camera Installation ADJUST POSITION 1. T urn on power to the camera and monitor . 2. V arifocal lens only: Loosen the focal length and fo ...
-
Pelco ICS210 - page 11
C2491M-D (8/06) 11 REPLACE COVER Place the cover of the ICS210 onto the base of the unit. Using the screwdriver bit (supplied), tighten the three tamperproof screws. NOTE: Remove the foam from the inside of the cover before installing the cover . ...
-
Pelco ICS210 - page 12
12 C2491M-D (8/06) Adjustments (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, iris level, focus, or switch settings (refer to proc ...
-
Pelco ICS210 - page 13
C2491M-D (8/06) 13 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fi xed focal length lens with an auto iris, you can adjust the iris level setting to increase or decrease brightness. Figure 12. Iris Level Adjustment FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS T o adjust the focus, do the following: 1. Loosen the lockin ...
-
Pelco ICS210 - page 14
14 C2491M-D (8/06) HEATER BOARD REMOVAL T o remove the heater board, do the following: 1. Disconnect the four -pin heater connector (red, orange, and black wires) if it is plugged in. Figure 14. Removing Heater Board 2. Wait for the heater elements to cool if they are hot. 3. Apply pressure and press on the corner of the board. WARNING: Heater elem ...
-
Pelco ICS210 - page 15
C2491M-D (8/06) 15 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to Figure 15 . The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there are no bright spots that darken other picture details. M ...
-
Pelco ICS210 - page 16
16 C2491M-D (8/06) SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. Figure 17. Switch Settings for Varifocal Lens For manually setting and locking the white balance Place a white background in front of camera and turn off switch 1. For gamma corre ...
-
Pelco ICS210 - page 17
C2491M-D (8/06) 17 Specifications General Pan/T ilt Adjustment Manual; 5° above horizontal to 20° below horizontal tilt; 24° pan adjustment when using the adjustable mounting pattern in base Rating Meets NEMA T ype 4X and IP66 standards Construction Aluminum mounting plate, base, and cover, steel camera mounting bracket Finish Gray polyester po ...
-
Pelco ICS210 - page 18
18 C2491M-D (8/06) REVISION HISTORY Manual # Date Comments C2491M 6/05 Orginal version. C2491M-A 7/05 Revised per new camera shell design for varifocal lens. C2491M-B 10/05 Revised switch-setting descriptions for varifocal lens. C2491M-C 1/06 Revised factory switch settings for varifocal lens. Updated wiring information. C2491M-D 8/06 Updated mount ...
-
Pelco ICS210 - page 19
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series p ...
-
Pelco ICS210 - page 20
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherlands United Arab Emirates | United Kingdom | United St ...
У вас вопрос, касающийся Pelco ICS210?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Pelco ICS210, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Pelco ICS210 со всей вероятностью он захочет поделиться методом ее решения.