-
Generac Power Systems 004701-0 - page 1
Owner’ s Man ual and Installation Instructions Air -cooled Recreational V ehic le Generators • Model: 004701-0 QUIETP A CT 40LP This manual should remain with the unit. ...
-
Generac Power Systems 004701-0 - page 2
I NTRODUCTION Thank you for purchasing this model by Generac P ower Systems Inc. It has been designed and manu- factured to supply electrical power for recreational vehicles. R EAD THIS MAN UAL THOROUGHL Y If any portion of this manual is not understood, con- tact the nearest Authorized Service Dealer for starting , operating and servicing procedur ...
-
Generac Power Systems 004701-0 - page 3
T able of Contents Recreational V ehicle Generator 1 Part I – Owner’s Manual Introduction ........................................ Inside Front Cover Read This Manual Thoroughly ................................. IFC Contents .................................................................. IFC Operation and Maintenance ........................ ...
-
Generac Power Systems 004701-0 - page 4
2 Study these SAFETY RULES carefully before install- ing, operating or servicing this equipment. Become familiar with this Owner’s Manual and with the unit. The generator can operate safely , efficiently and reliably only if it is properly installed, operated and maintained. Many accidents are caused by failing to follow simple and fundamental ru ...
-
Generac Power Systems 004701-0 - page 5
3 • Adequate, unobstructed flow of cooling and ven- tilating air is critical to correct generator opera- tion and is required to expel toxic fumes and fuel vapors from the generator compartment. W ithout sufficient cooling airflow , the engine/generator quickly overheats, which causes serious damage to the generator . Do not alter the installatio ...
-
Generac Power Systems 004701-0 - page 6
4 1. Generator Air Intake 2. Engine Start/Stop Switch 3. F use 4. Optional Remote P anel Receptacle (Side V iew) 5. Generator AC Output Leads (Side V iew) 6. F uel Primer Switch 7. Circuit Breaker 8. Starter Contactor 9. F uel Inlet 10. F uel Pump (Behind Access P anel) 11. LP Regulator/Solenoid 12. Oil Filter 13. Oil Drain Cap 14. Oil Dipstick 15. ...
-
Generac Power Systems 004701-0 - page 7
5 Section 1 – General Information Recreational V ehicle Generator 1.2 GEN ER A T OR AP P LICAB I LIT Y These generators have been designed and manufac- tured for supplying electrical power for recreational vehicles. Do not modify the generator or use it for any application other than for what it was designed. If there are any questions pertaining ...
-
Generac Power Systems 004701-0 - page 8
6 1.5.3 ENGI N E OIL R EQ UIRE MEN T S Use only high quality detergent oil rated with American P etroleum Institute (API) Service Classification SF , SG or SH. The recommended oil weights include the following: • During summer months: SAE 30. An acceptable substitute is SAE 10W -30. • During winter months: SAE 5W -30. DO NOT USE SAE 10- W40. Cr ...
-
Generac Power Systems 004701-0 - page 9
7 Section 2 – Operation Recreational V ehicle Generator 2.1.4 MAI N BR EAKER The main breaker protects the generator’s AC out - put circuit against overload and provides a method of turning OFF the generator’s 120-volt AC output to the vehicle circuits. This generator has a 30-amp breaker . 2.2 OPTIONAL R EMO TE S T ART/ST OP P AN EL A remote ...
-
Generac Power Systems 004701-0 - page 10
8 Section 2 – Operation Recreational V ehicle Generator T o start the generator from either the generator con- trol panel or from the optional remote panel, proceed as follows: 1. T urn OFF electrical loads using the means pro - vided in the vehicle (such as a main line circuit breaker or transfer switch). NOTE: If starting from the generator con ...
-
Generac Power Systems 004701-0 - page 11
9 Section 2 – Operation Recreational V ehicle Generator 2.8.2 H IGH TEM PER A TU R E SWIT CH This switch (Figure 2.2), which has normally open (N .O .) contacts, is mounted near the oil filter . The contacts close if the temperature should exceed approximately 284º F (140º C), initiating an engine shutdown. Figure 2.2 – Low Oil Pressure and H ...
-
Generac Power Systems 004701-0 - page 12
10 2.9.2 25-HOUR CHECK-U P After the 25-hour break -in period, contact an Authorized Service Dealer for the following main- tenance. The vehicle owner is responsible for any charges: • Change the engine crankcase oil and oil filter . • Check the oil level. • Inspect the cooling and ventilation openings. • Check the engine carburetor adjustm ...
-
Generac Power Systems 004701-0 - page 13
11 Section 3 – Maintenance Recreational V ehicle Generator 4. If necessary , remove the oil fill cap on the rocker cover and slowly add oil until it reaches the dip - stick “F ull” mark. DO NOT FILL ABOVE THE “FULL ” MARK. Never operate the engine with the oil level below the “Add” mark on the dipstick. Doing this could damage the ...
-
Generac Power Systems 004701-0 - page 14
12 Section 3 – Maintenance Recreational V ehicle Generator 3.3.2 CLEAN ING OR R EP L ACING TH E P AP ER F I L TER Once each year or every 100 hours of operation (whichever comes first), clean or replace the paper filter . The new replacement filter must be flame retardant. Service the paper filter more frequently if operating the generator in ext ...
-
Generac Power Systems 004701-0 - page 15
Section 3 – Maintenance Recreational V ehicle Generator Figure 3.5 - Spark Arrestor RET AINING SCREW P/N 056892 SP ARK ARRRESTOR SCREEN P/N 089680 T AILPIPE P/N 0E0683 3.7 CLEAN I NG TH E GEN ER A T OR Keep the generator set as clean and dry as possible. Protect the unit against excessive dust, dirt, corrosive vapors, road splash, etc. P ermittin ...
-
Generac Power Systems 004701-0 - page 16
14 • Where electr olyte contacts the eyes, flush thoroughly and immediately with water and seek medical attention; and • Spilled electrolyte is to be washed down with an acid neutralizing agent. A common practice is to use a solution of 1 pound (500 grams) bicarbonate of soda to 1 gallon (4 liters) or water . The bicar - bonate of soda solution ...
-
Generac Power Systems 004701-0 - page 17
15 2. When valve clearance is correct, hold the pivot ball stud with the allen wrench and tighten the rocker arm jam nut with a crows foot. Tighten the jam nut to 65-85 inch-pounds torque. After tightening the jam nut, recheck valve clearance to make sure it did not change (Figure 3.7). Figure 3.7 — T ightening Jam Nut 3.1 3 RV GEN ER A T OR SERV ...
-
Generac Power Systems 004701-0 - page 18
16 Section 4 – Notes Recreational V ehicle Generator ...
-
Generac Power Systems 004701-0 - page 19
P ART I I – I NS T ALL A TION I NS TR UCTIONS D ANGER ONL Y QUALIFIED ELECTRICIANS OR CONTRACTORS SHOULD A TTEMPT INST ALLA TION!! ...
-
Generac Power Systems 004701-0 - page 20
18 NO TICE T O I NST ALLER These Installation Instructions have been published by the manufacturer to aid in the installation of the products described in this manual. The manufac- turer assumes that installation personnel are familiar with the procedures for installing such products, or similar products manufactured. The manufacturer also assumes ...
-
Generac Power Systems 004701-0 - page 21
19 ELE CTR ICAL HA Z AR DS • The generator covered by this manual produces dangerous electrical voltages and can cause fatal electrical shock. A void contact with bare wires, ter - minals, connections, etc., while the unit is running . Ensure all appropriate covers, guards and barriers are in place before operating the generator . If work ...
-
Generac Power Systems 004701-0 - page 22
20 1.1 P U R POSE AN D S COPE OF TH E MAN U AL These Installation Instructions have been prepared especially for the purpose of familiarizing installers and owners of the applicable equipment with the product's installation requirements. Give serious consideration to all information and instructions in the manual, both for safety and for conti ...
-
Generac Power Systems 004701-0 - page 23
21 Figure 1.2 – Major Features and Dimensions (Drawing No. 0F4610) Section 1 – General Information Recreational V ehicle Generator 3 42. 2 [1 3 1/2"] 77 8 . 9 [ 3 0 11/16" ] REF. FR O NT D OO R A CC E SS F OR ALL RE Q UIRED MAINTENANC E REM O TE PANE L CO NNE C T OR 500 . 2 [ 1 9 11/16" ] REF. A C OU TP UT HARNE SS H O T AI R EXH ...
-
Generac Power Systems 004701-0 - page 24
22 2.1 L OCA TION AN D SU P PORT 2.1.1 GEN ERA T OR L OCA TION The most desirable location for the generator set is between the vehicle's main frame members. However , this is seldom possible. Most units must be installed on the side of the vehicle and are difficult to rein- force. Many recreational vehicles have been factory equipped with an ...
-
Generac Power Systems 004701-0 - page 25
23 2.2 GEN ER A T OR C OM P ARTM ENTS Whether the generator set is being installed inside a compartment specifically manufactured to house a generator or inside a compartment that the installer constructs, the compartment must meet certain spec- ifications as outlined in the following sections: 2.2.1 COMP ARTM ENT SIZE Plan the compartment size car ...
-
Generac Power Systems 004701-0 - page 26
24 Figure 2.5 – T ypes of Lock Seams D ANGER Do not install any flammable material directly above or around the compartment. Heat, trans- ferred thr ough the compartment structure, may be sufficient to ignite, char or discolor seat cush- ions, fiberboard and other flammable materials. Use approved nonflammable insulating materi- als in high t ...
-
Generac Power Systems 004701-0 - page 27
25 Section 2 – Installation Recreational V ehicle Generator Figure 2.7 – Compartment Floor Cutout (Drawing 0G3723-A) ...
-
Generac Power Systems 004701-0 - page 28
26 D ANGER Fuel lines and exhaust piping must not pen- etrate into the vehicle living area. 2.3 C OOLI NG AN D VENTI L A TI NG AI R It is absolutely essential that an adequate flow of air for cooling, ventilating and engine combustion be supplied to the generator set. W ithout sufficient airflow , the engine/generator quickly overheats. Such ov ...
-
Generac Power Systems 004701-0 - page 29
27 Figure 2.9 – T ypical Propane Gas Fuel System 2.4.2 SOME I M PORT ANT CONSIDER A TIONS When installing an LP gas system, consider seriously the following items: • All fittings, lines, hoses and clamps must be tight and free of leaks. Apply a pipe sealant to threads when assembling threaded connections. This reduces the possibility of leakage ...
-
Generac Power Systems 004701-0 - page 30
28 The greater the airflow through the carburetor ven- turi, the lower the pressure at the venturi throat. The lower the pressure at the venturi throat, the greater the diaphragm movement, and the greater the move - ment of the regulator valve. The more the regulator valve opens, the greater the gas flow that is propor - tional to airflow through t ...
-
Generac Power Systems 004701-0 - page 31
29 2.5.1 SP AR K ARR ES T OR This spark arrestor assembly meets code and stan- dard requirements of the U .S. F orest Service. Use only mufflers and parts approved by the manufactur - er . Any person(s) installing an unapproved muffler , or an unapproved exhaust system part, or modifying an exhaust system in any way that might cause a hazard, is li ...
-
Generac Power Systems 004701-0 - page 32
30 • W iring must be of adequate size, have approved insulative qualities and be properly supported. • Conduit and wire openings into the generator com- partment (if used) must be vapor - sealed to prevent entry of flammable, explosive or poisonous gases into the vehicle. 2.6.1 ELECTRICAL JU NCTION BOX Install an approved, square electrical jun ...
-
Generac Power Systems 004701-0 - page 33
31 Section 2 – Installation Recreational V ehicle Generator Figure 2.14 – T ransfer Switch Isolation Method Figure 2.15 – Installation With Isolation Receptacle ...
-
Generac Power Systems 004701-0 - page 34
32 2.6.6 POWER SUP P L Y CORD The power supply cord must comply with all appli- cable codes, standards and regulations. It must be large enough to handle the full amperage to which it will be subjected. 2.6.7 GROU ND F AU L T CI RCUIT I NTERR U PTERS The National Electrical Code (NFP A 70, 551-7) requires that a ground fault circuit interrupters (G ...
-
Generac Power Systems 004701-0 - page 35
33 Section 3 – Post-installation Start-up Adjustments Recreational V ehicle Generator Figure 2.17 – Remote Panel Plug-in Receptacle 12.00" 14 0 17 1 5 1 8 14A 1 3 2 5 4 6 0 14 17 1 8 14A 1 5 1 5 17 14A 1 8 14 0 N o. WIRE WIRE CO L OR RED YELL OW O RAN GE WHITE BL UE BR O W N 12.0 ( 305 ) LENGTH ( mm ) 12.0 ( 305 ) 12.0 ( 305 ) 12.0 ( 305 ) ...
-
Generac Power Systems 004701-0 - page 36
34 6. T urn off all electrical loads by setting the gener- ator’s main circuit breakers to their “OFF” (or open) position. 7. Let the unit run at no -load for a few minutes to stabilize internal engine/generator temperatures. Then, shut down the engine. NOTE: The generator set was thoroughly tested and adjusted at the factory before shipping ...
-
Generac Power Systems 004701-0 - page 37
35 Section 3 – Post-installation Start-up Adjustments Recreational V ehicle Generator 3.5 I NS T ALL A TION CH E CKLIST L OCA TION AN D SU P PORT ❑ Generator is properly located. ❑ Generator is properly supported. ❑ Generator is properly restrained. GEN ERA T OR COMP ARTM ENT ❑ Compartment construction is proper . ❑ Holes/Openings are v ...
-
Generac Power Systems 004701-0 - page 38
36 TROU B LE SHOO TI NG GU I DE Problem Cause Correction The engine will not crank. 1. F use blown 1. Replace fuse. 2. Loose, corroded or defective 2. Tighten, clean or replace battery cables as necessary . 3. Defective engine Start/Stop 3. Replace Start/Stop switch. switch 4. Defective starter contactor 4. Replace contactor . 5. Defective starter ...
-
Generac Power Systems 004701-0 - page 39
37 Section 5 – Notes Recreational V ehicle Generator ...
-
Generac Power Systems 004701-0 - page 40
RED BLUE ORANGE BROWN 7 7 YELLOW WHITE 15 BA TTERY CHARGE WINDING NEUTRAL CONNECTION GREEN BY CU S TOMER WHITE T2 FIELD 120V 30A 44 0F 0N 0K 22P DPE WINDING 2 CB3 6 ELECTRONIC REGULA TOR VOLT AGE 2A 0N 0N R1 POWER WINDING 22 S 11 S 77 55 BLACK FUEL PRIME 11P 4 4 T1 4 CB1 REMOTE P ANEL (OPTIONAL) 33 4 66 S TA R T HM L1 1 S TOP 8 A 4 1 8 5 14 18 0 17 ...
-
Generac Power Systems 004701-0 - page 41
39 Section 6 — Electrical Data Recreational V ehicle Generator Electrical Schematic and Wiring Diagram – Drawing No. 0D8063-D 0 CONN. 2 PIN# 0 90 14 14 CH 18A 90 85 LOP C S 0 18 RED 18 85 17 18A 85 PCB J1-7 J1-9 J1-12 J1-11 J1-10 J1-8 J1-15 J1-14 J1-13 J1-2 J1-5 J1-4 J1-3 J1-1 J2 J1-6 J3 18 1 F S 14 2 3 18 18A 18 CONN. 1 PIN# 0 0 FP 90 14 2 1 2 ...
-
Generac Power Systems 004701-0 - page 42
40 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator Enclosure – Drawing No. 0F4589-B ...
-
Generac Power Systems 004701-0 - page 43
41 ITEM P ART NO . QTY . DESCRIPTION 1 0F3916 1 TRA Y , ENCLO S URE 2 0D6942 1 P ANEL, ENCLO S URE S IDE 3 0D6939 1 P ANEL, REAR DIVIDER 4 0F3920 1 P ANEL, ENCLO S URE ROOF 5 0F3917 1 P ANEL, ENCLO S URE BACK 6 0F3918 1 P ANEL, FRONT DIVIDER 7 0F3919 1 COMP ARTMENT , AIR INT AKE 8 0G7329 1 P ANEL, ENCLO S URE DOOR 9 0D8254 1 S HIELD , MUFFLER 10 0C ...
-
Generac Power Systems 004701-0 - page 44
42 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator Generator – Drawing No. 0F4590-C ...
-
Generac Power Systems 004701-0 - page 45
43 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator Generator – Drawing No. 0F4590-C ITEM P ART NO . QTY . DESCRIPTION 1 029092 1 S CREW IHHC 5/16”-24 X 11-1/4” G5 2 022129 22 W A S HER LOCK M8-5/16” 3 049451 1 W A S HER FLA T .406” I.D . X 1.62” O .D . 4 0C8096A 1 F AN, 8" CUR VE BLADE, 16.5MM I.D . 5 ...
-
Generac Power Systems 004701-0 - page 46
44 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator Control Panel – Drawing No. 0F45 9 1 -A ...
-
Generac Power Systems 004701-0 - page 47
45 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator Control Panel – Drawing No. 0F45 9 1 -A ITEM P ART NO . QTY . DESCRIPTION 1 0F9719 1 REGULA TOR V OL T AGE 2 075210A 1 TERMINAL BLOCK 3 092234 1 CONTROLLER P .C.B. 4 065795 1 BA TTERY CHARGER RECTIFIER 5 023484F 2 BU S HING S NAP 1” 6 023484R 1 BU S HING S NAP 1-1/ ...
-
Generac Power Systems 004701-0 - page 48
46 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator GN-22 0 H/SH Engine – Drawing No. 0F57 9 1-G P art 1 ...
-
Generac Power Systems 004701-0 - page 49
47 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator GN-22 0 H/SH Engine – Drawing No. 0F57 9 1-G P art 1 ITEM P ART NO . QTY . DESCRIPTION 1 0D8433 1 GUARD , F AN 2 0C1069 10 S CREW , HHTT M6-1.0 X 8mm 11 (04701-1 ONL Y) 3 090695F 1 BLOWER HOU S ING 0G6468 1 BLO WER HOU S ING (04701-1 ONL Y) 4 081810 1 NUT , HEX M16-1 ...
-
Generac Power Systems 004701-0 - page 50
48 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator GN-22 0 H/SH Engine – Drawing No. 0F57 9 1-G P art 2 ...
-
Generac Power Systems 004701-0 - page 51
49 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator GN-22 0 H/SH Engine – Drawing No. 0F57 9 1-G P art 2 ITEM P ART NO . QTY . DESCRIPTION N/A 0F5800 1 LONG BLOCK A SS EMBL Y 220 RV LP 1 078621 1 CONNECTING ROD A SS EMBL Y 2 076389 1 PI S T ON PIN 3 0G4379 1 RING S ET , PI S TON DIA 75 4 0A8897B 1 GEAR CO VER A SS EMB ...
-
Generac Power Systems 004701-0 - page 52
50 9 14 12 11 1 8 1 6 1 3 1 5 17 1 9 2 3 21 2 0 22 2 5 24 2 6 8 1 0 4 6 5 3 2 1 7 Section 7 — Exploded Views and P arts Lists Recreational V ehicle Generator Regulator – Drawing No. 0F58 1 9 ...
-
Generac Power Systems 004701-0 - page 53
51 ITEM P ART NO . QTY . DESCRIPTION 1 0D5694 1 CA S TING, TWIN REGULA TOR HOU S ING 2 0F4795 4 S CREW PPHM S EM S M4-0.7 X 10 3 0F5022 1 S OLENOID COIL, 12VDC 4 0C6070 1 S PRING- S OLENOID PLUNGER 5 0C4680 1 PLUNGER LP REG. A SS Y 6 0C4647 1 GA S KET , S OLENOID 7 0C4643 1 INLET , TWIN REGULA TOR NO HOLE 8 0D3973 1 PLUG, EXP AN S ION 16MM TWINREG ...
-
Generac Power Systems 004701-0 - page 54
52 CALI FOR N IA AND F EDER AL EM ISSION C ONTROL W AR R ANT Y ST A TEM ENT Y OU R W ARR ANT Y RIGHTS AN D OBLIGA TIONS The California Air Resources Board (CARB) and the United States Environmental Protection Agency (EP A), together with Generac P ower Systems, Inc. (Generac), are pleased to explain the Emission Control System W arranty on your new ...
-
Generac Power Systems 004701-0 - page 55
53 EM IS SION CONTROL S Y STEM W AR R ANT Y Emission Control System W arranty (ECS W arranty) for 1997 and later model year engines: (a) Applicability: This warranty shall apply to 1997 and later model year engines. The ECS W arranty Period shall begin on the date the new engine or equipment is purchased by/delivered to its original, end-use purcha ...
-
Generac Power Systems 004701-0 - page 56
Part No. 0F4594 Revision D (10/22/07) Printed in U.S.A. Section 8 – W arranty Recreational V ehicle Generator GENERA C PO WER SYSTEMS’ THREE-YEAR LIMITED W ARRANTY FOR GU ARDIAN RECREA TIONAL VEHICLE GENERA T ORS NO TE: ALL UNITS MUST BE INST ALLED BY GENERAC PO WER SYSTEMS AUTHORIZED SER VICE F ACILITIES. F or a period of 3 (three) years of op ...
У вас вопрос, касающийся Generac Power Systems 004701-0?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Generac Power Systems 004701-0, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Generac Power Systems 004701-0 со всей вероятностью он захочет поделиться методом ее решения.