-
Trek 9i - page 1
C L K T M E A V G M A X T R P A V G M P H F This manual explains the installa- tion and use of the Trek Incite 9i and 11i bicycle computer . Please read this manual carefully and ...
-
Trek 9i - page 2
Safety and general guidelines .................................................. 1 F unctions .................................................................................. 2 Installation ................................................................................ 4 Placing the computer on the handlebar .... ...
-
Trek 9i - page 3
While riding your bicycle, do not stare at the computer for long periods of time (Figure 1). If you do not watch the road, you could hit an obstacle, which may cause you to lose control and fall. Make sure the computer wire cannot contact the tire or whe ...
-
Trek 9i - page 4
...
-
Trek 9i - page 5
...
-
Trek 9i - page 6
T ools needed: • Electrical tape • Slot-type screwdriver • Phillips-type screwdriver • Scissors Stem mount Handlebar mount Speed sensor ? ...
-
Trek 9i - page 7
The Trek Incite 9i or 11i computer can be mounted on the handlebar or on the stem (Figure 3). 1. Select the bar c ...
-
Trek 9i - page 8
Check that the computer base cannot be rotated around the handlebar , and that the computer cannot slide backwards on the computer base (Figure 5). 1. Insert the rubber friction pad into the compu ...
-
Trek 9i - page 9
The wheel magnet must be aligned so that it passes across the sensor . As the magnet passes the sensor , it must be no further from the sensor than 1 to 3mm (1/32 to 1/8 inch). The wheel magnet has a ‘T’ shaped slot with two configura- tions: round spokes and flat or bladed spokes (Fi ...
-
Trek 9i - page 10
The computer wire is usually longer than needed. Extra wire length can be diverted by wrapping it around the brake housing prior to routing it down the fork blade or down tube (Figure 8). Make sure the computer wire is not pulled tight when the handlebar is turn ...
-
Trek 9i - page 11
The magnet must pass across the line on the sensor (Figure 9). These instructions are written for the front wheel, but apply equally to installing the magnet and cadence sensor which go on the lef t crank and the frame’s chainstay (Figure 10). ? ...
-
Trek 9i - page 12
and magnet by spinning the wheel and noting if the computer is displaying speed. If the computer shows current speed, the sensor is r eading the magnet. If the computer is not displaying a value, realign the sensor and magnet until one is displayed. 5. Tighten the nylon ties and trim the excess length (Figure 11). ...
-
Trek 9i - page 13
Y ou can program the starting values of your computer in a single, easy procedure: • Units • Clock • Wheelsize • Odometer The Units setting tells the computer which conversion to use: metric or SAE (“English”): MH = miles KMH = kilometers Y ou can set the clock for 12 or ...
-
Trek 9i - page 14
CL K TME A VG MA X TRP A VG MPH F Mode Set When setting the computer , t ...
-
Trek 9i - page 15
CLK TME AVG MAX TRP ODO MH Mode Set 3. Cycle Mode MH and KMH inter change on the screen. 4. Push Set• to select. The temperature icon display . 5. Cycle Mode to C or F 6. Push Set• to select. The computer returns to the start scr een. 1. Cycle Mode to ODO (Figure 13). 2. Hold S ...
-
Trek 9i - page 16
CLK TME AVG MAX TRP ODO MH Mode Set Both the 9i and 1 1i allow you to use two differ ent wheel sizes. The icon for Wheel 1 is a small cir cle. The icon for Wheel 2 is a partial circle surr ounding the Wheel 1 icon (Figure 14). 1. Cy ...
-
Trek 9i - page 17
CLK TME AVG MAX TRP ODO MH Mode Set 1. Cycle Mode to TRP 2. Hold the lef t Mode and the right Mode together . The Wheel Select icon changes (Figure 14). Repeat step 2 to change again. ...
-
Trek 9i - page 18
CLK TME AVG MAX TRP ODO MH Mode Set 1. Cycle Mode to CLK (Figure 15). 2. Hold Set• “12” or “24” flashes. CL K TM E AV G MAX TR P A VG MPH F 3. Cycle Mode 12 and 24 inte ...
-
Trek 9i - page 19
CLK TME AVG MAX TRP ODO MH Mode Set Y our computer stores data for two intervals- since last ReSet and since last R eStart. R eSet sets ALL data to zero. R eStart sets only the Trip data to zero. The trip modes include • TRP • TME • MAX T ...
-
Trek 9i - page 20
CLK TME AVG MAX TRP ODO MH Mode Set Once the computer is programmed and installed, it is very easy to use. To change to different modes (functions), simply Cycle the Mode button until the desired function appears, shown by the spell ...
-
Trek 9i - page 21
The Incite 9i computer is designed to be easy to install and maintain. However , computers occasionally have problems. T able 3 shows some possible problems, causes, and solutions: ...
-
Trek 9i - page 22
If the computer is giving erratic information, the computer or hear rate strap battery may be running low on power (normally accompanied by the low battery icon, Figure 16). R eplace the batteries whenever the computer malfunctions, or every 6 months. When purchasing new ba ...
-
Trek 9i - page 23
4. Lif t the battery cover , exposing the battery . Be careful to avoid losing the rubber O-ring seal. 5. R emove the old battery . It may be possible to shake the battery out. Otherwise, carefully pry the battery up with a thin tool or knife blade. 6. Insert the new battery wit ...
-
Trek 9i - page 24
CLK TME AVG MAX TRP ODO MH Mode Set The procedure is almost the same as the basic setup on pages 13-14, except instead of picking a wheel size from the menu, you can program in a 4-digit number . ? ...
-
Trek 9i - page 25
CLK TME AVG MAX TRP ODO MH Mode Set 4. Push Mode to select. Wheel size appears. Note : If you want to set a cus tom wheel size, go to pa ge 24 now . 5. Cycle Mode through the wheel sizes tro the 4-digit number . 6. Push Set• The left-hand digit flashes. 7. Cycle Mode to the desired value. 8. Push Set• to select. The next digit flashes. 9 ...
-
Trek 9i - page 26
T able 1 approximates the circ ...
-
Trek 9i - page 27
Tr ek Bi cyc le Co rpo ra ti on war ra nt s ea ch new In ci te c om pu ter ag ai ns t de fe ct s in wo rk man sh ip and ma te ria ls . Tr ek In cit e c om put er mo del s 6 i, 8i, ...
У вас вопрос, касающийся Trek 9i?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Trek 9i, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Trek 9i со всей вероятностью он захочет поделиться методом ее решения.