-
Grizzly H6144 - page 1
COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL6904 PRINTED IN CHINA 3 4 º A N G L E F I N I S H N A I L E R - 2 ½ " MODEL H6144 INSTRUCTION MANUAL ...
-
Grizzly H6144 - page 2
For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. R ...
-
Grizzly H6144 - page 3
H6144 34° Angle Finish Nailer–2½" -2 - -2 - 6. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PER- SONNEL TO OPERATE MACHIN- ERY. Make sure operation instruc- tions are safe and clearly under- stood. 7. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visi- tors a safe distance from the work area. 8 . MAKE WORKSHOP CHILD PROOF. Use padlo ...
-
Grizzly H6144 - page 4
H6144 34° Angle Finish Nailer–2½" -3 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source . Only use fil- t ...
-
Grizzly H6144 - page 5
H6144 34° Angle Finish Nailer–2½" -4 - Operating this nailer can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this nailer discharges at 85-90 decibels. To protect y ...
-
Grizzly H6144 - page 6
H6144 34° Angle Finish Nailer–2½" -5 - INTRODUCTION If you have any c omm ents r egar ding t his man ual, pl ease write t o us at th e foll owing add ress : Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Mo st i mpo rt ant ly , we s tan d b ehin d ou r too ls. If you have any ser vi ce que sti ...
-
Grizzly H6144 - page 7
H6144 34° Angle Finish Nailer–2½" -6 - SET UP Figure 1. Model H6144 inventory. B C D G Unpacki ng Y our M od el H 61 4 4 l eft our w areho use in a ca reful ly pac ked b ox. If you d isc over th e na ile r is d am age d af te r you h ave sig ned for d eli ver y , pl ease im med iatel y cal l Cus tomer S ervi ce at ( 57 0 ) 546 - 96 63 for ...
-
Grizzly H6144 - page 8
H6144 34° Angle Finish Nailer–2½" -7 - -7 - Compressed Air Sy stem The M ode l H 61 44 is de sig ned to be op er- ated at 6 0 - 1 0 0 PSI us ing cle an, d ry, reg u- late d, c omp ress ed air . DO N OT exc ee d th e max imum o pe rati ng pr ess ure fo r your mod el . Befo re u sin g you r new n ailer, in sta ll a 1 ⁄ 4 " NPT male qu ...
-
Grizzly H6144 - page 9
H6144 34° Angle Finish Nailer–2½" -8 - Safety Y oke A safe ty yo ke mec han ism o n the nos e of t he nai ler ac ts a s a se con dar y saf ety devi ce. Whe n t he tri gge r i s pr ess ed, th e nai ler wi ll no t fire unt il t he s afety yoke mec han ism is dep ress ed. Befo re you us e your na iler fo r the fi rst tim e, che ck th e safet ...
-
Grizzly H6144 - page 10
H6144 34° Angle Finish Nailer–2½" -9 - OPERATIONS Loadin g When replacing nails in your Model H6144, follow these guidelines: Gauge: 15 Length: 1 1 ⁄ 4 " -2 1 ⁄ 2 " Capacity: 40 Angle: 34 ° NOT IC E : A n umb er o f m anufa ctur ers' nai ls m ay fit th e M ode l H 61 4 4. H owever , for best per for man ce, we re com me ...
-
Grizzly H6144 - page 11
H6144 34° Angle Finish Nailer–2½" -10 - Figure 5. Depth adjustment knob. Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects. 5. Pull the trigger. If the nail drove into the wood far enough, continue with your intended operations. If the nail went t ...
-
Grizzly H6144 - page 12
H6144 34° Angle Finish Nailer–2½" -11 - The most frequent situation with any type of nailer is a nail jam. A jammed nail must be cleared before using the nailer again. T o cl ea r a j amm ed n ail f rom th e dis - cha rg e ar ea on th e M ode l H 6144 : 1. DISCONNECT NAILER FROM THE AIR SUPPLY! Figure 7. Releasing quick release latch. Figu ...
-
Grizzly H6144 - page 13
H6144 34° Angle Finish Nailer–2½" -12 - Replacin g Pist ons / O - Rin gs If yo u us e your na iler day in and day out , rep air pisto ns are c hea p ins uran ce agai nst wa sted d own tim e and lo st prof its, in the event that a p isto n or pi ston sh aft bec ome s wo rn out. Always disconnect air from nailer whenever servicing! During ma ...
-
Grizzly H6144 - page 14
H6144 34° Angle Finish Nailer–2½" -13 - CLEANING & LUBRICATION Cleanin g Use a go od s olven t to c lean the no se ass emb ly of t he n aile r . Always b e sure th at t he n ail er i s dr y b efor e us in g it agai n. Do not a llow du st, c hips , s and, et c. into the air c onne cto rs o r into th e bo dy o f th e nai ler; th is may r ...
-
Grizzly H6144 - page 15
H6144 34° Angle Finish Nailer–2½" -14 - H6144 PARTS BREAKDOWN ...
-
Grizzly H6144 - page 16
H6144 34° Angle Finish Nailer–2½" -15 - H6144 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6144001 SPECIAL CAP SCREW M5-.8 X 12 45 PH6144045 STEEL BALL 2MM 2 PH6144002 AIR DEFLECTOR 46 PH6144046 SAFETY SEAT 3 PH6144003 RUBBER WASHER 10 MM 47 PH6144047 DRIVE PIN 4 PSB38M CAP SCREW M5-.8 X 25 48 PR39M EXT RETAINING RING 8MM 5 ...
-
Grizzly H6144 - page 17
H6144 34° Angle Finish Nailer–2½" -16 - 1. O-rings must be replaced & operation of safety yoke must be checked. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting & use teflon tape. 1. Replace damaged seals. 1. Tighten screws and fit - tings. 2. Clean nose. 3. Clean magazine and inspect/repair damage. 4. Check fitting, ho ...
-
Grizzly H6144 - page 18
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warr ...
-
Grizzly H6144 - page 19
Name _________________________________________________________________________ Street ________________________________________________________________________ City____________________State________Zip_________ Phone Number____________E-Mail___________________FAX ____________ Model # H6144 34°Angle Finish Nailer–2½" Serial#________________Or ...
-
Grizzly H6144 - page 20
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here ...
У вас вопрос, касающийся Grizzly H6144?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Grizzly H6144, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Grizzly H6144 со всей вероятностью он захочет поделиться методом ее решения.