-
TOA Electronics RD-36 - page 1
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1 36" Wood Burning Fireplaces P/N 700,009M REV. D 11/2003 RD-36 HC-36 RD-36-H HC-36-H RDI-36 HCI-36 RDI-36-H HCI-36-H MODELS CUSTOM SERIES This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and under- stand these ...
-
TOA Electronics RD-36 - page 2
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 2 TABLE OF CONTENTS Safety Rules .................................... page 2 Tools and Building Supplies ............ page 2 Precautions ..................................... page 3 Introduction ..................................... page 3 Clearances/Height Requirements ..... page 3 Chimney System .. ...
-
TOA Electronics RD-36 - page 3
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3 Figure 1 TYPICAL INSTALLATION *Construction Materials: • framing materials • paneling • particle board • flooring • millboard • dry wall • plywood • etc. PRECAUTIONS Note: These fireplace systems are not difficult to install. However, in the interest of safety, it is recommended tha ...
-
TOA Electronics RD-36 - page 4
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 4 WARNING: IF INSULATION IS USED, THE FIREPLACE MUST NOT BE PLACED DI- RECTLY AGAINST IT. INSULATION OR VAPOR BARRIERS, IF USED, MUST FIRST BE COVERED WITH GYPSUM BOARD, PLYWOOD, PARTICLE BOARD OR OTHER MATERIAL TO ASSURE INSULATION AND VAPOR BARRIERS REMAIN IN PLACE. Figure 2 Chimney Height The tota ...
-
TOA Electronics RD-36 - page 5
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5 Note: Install the hearth extension only as illus- trated. The safety strips should extend from front of the fireplace at least 1 ¹⁄₂ " and should extend to be at least flush with the sides. In the event a wooden support is used to elevate the fireplace above the floor, a “Z” type safe ...
-
TOA Electronics RD-36 - page 6
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 6 FIREPLACE SPECIFICATIONS Figure 10 Blocking Metal Safety Strips Figure 8 Figure 9 Step 3. Refer to fireplace drawings and specifi- cations on pages 6 and 7 for framing dimensions and details. Frame appliance enclosure as illus- trated in Figures 11 through 14 on page 8. IMPORTANT: UNDER NO CIRCUMST ...
-
TOA Electronics RD-36 - page 7
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7 Figure 15 Figure 16 Figure 14 Framing Dimensions A 43" 1092 mm B 44 ¹⁄₂ " 1130 mm C 29 ¹⁄₂ " 749 mm D 15 ³⁄₄ " 400 mm E 73" 1854 mm F 36 ¹⁄₂ " 927 mm G 21 ³⁄₄ " 552 mm H 20 ³⁄₄ " 527 mm J 51 ⁵⁄₈ " 1311 mm Framing Dimen ...
-
TOA Electronics RD-36 - page 8
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 8 Step 4. Fireplace should be secured to side framing members using the full length nailing tabs at the top and bottom of the fireplace front face. Use 8d nails ( Figure 17 ). Figure 17 Note: The nailing tabs and the area directly behind the nailing tabs are exempt from the clearances described on pa ...
-
TOA Electronics RD-36 - page 9
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 9 Note: If there is a room above ceiling level, firestop spacer must be installed on the bottom side of the ceiling. If an attic is above ceiling level, firestop spacer must be installed on top side of ceiling joist (Figures 21 and 22 ). Figure 21 Figure 22 CHIMNEY 30 ° OFFSET THROUGH FLOOR OR CEILI ...
-
TOA Electronics RD-36 - page 10
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 10 Locking Band Mastic Step 9. Security Chimneys locking bands, Model FLB, may be required if the chimney extends too high above the roof flashing. As a general rule, if the chimney extends more than 6' above the roof flashing, the use of locking bands is advisable to strengthen the chimney asse ...
-
TOA Electronics RD-36 - page 11
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 11 Using a FTF8-CTDT Chase Termination: Refer to specific installation instructions in- cluded with the FTF8-CTDT chase termination for clearance and installation details. Using a FTF8-CT1 Chase Termination: Refer to specific installation instructions in- cluded with FTF8-CT1 chase terminations for c ...
-
TOA Electronics RD-36 - page 12
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 12 Step 2. Use “Height of Chimney Only” column in The Vertical Elevation Chart to determine combinations of chimney used above return elbow to achieve desired heights. Reference Components Effective Height Chart in vertical elevation chart section. 4. Determine amount of chimney height re- quired ...
-
TOA Electronics RD-36 - page 13
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 A B FTF8-ES30 Number of FTF8 Chimney Sections Offset Height Offset/Return FTF8-S4 (Inches) (Inches) Elbow Stabilizer 12" 18" 38" 48" 41 5 ³⁄₄ 10 0 0 0 0 92 4 ¹⁄₂ 10 1 0 0 0 12 29 ³⁄₄ 10 0 1 0 0 14 ¹⁄₄ 33 ¹⁄₂ 10 2 0 0 0 17 ¹⁄₄ 38 ¹⁄₂ 10 1 1 0 0 ...
-
TOA Electronics RD-36 - page 14
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 14 Figure 43 THIS FIREPLACE IS NOT INTENDED TO BE USED AS A SUBSTITUTE FOR A FURNACE TO HEAT AN ENTIRE HOME. USE FOR SUPPLE- MENTARY HEATING ONLY. HOUSE WIRING COVER PLA TE Replace Cover Plate After Electrical Hook-Up POWER TO THE FIREPLACE The Optional Blower Kit Operates on 115 volt 60 Hz 150 watts ...
-
TOA Electronics RD-36 - page 15
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 15 Figure 44 The FBK-100/200 Blower Kits are design cer- tified by Warnock Hersey for use with these appliances. Always check local building codes. Installation of the FBK Blower Kits must comply with local regulations as well as the National Electric Code. Combustion Air Kits These appliances are eq ...
-
TOA Electronics RD-36 - page 16
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 16 Hearth Extensions and Wall Shields A hearth extension must be installed with all fireplaces. It is to protect the combustible floor in front of the fireplace from both radi- ant heat and sparks. The hearth extension must extend 8" beyond both sides of the fireplace opening and 16" beyond ...
-
TOA Electronics RD-36 - page 17
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 17 Figure 48 Figure 49 Methods of Determining Hearth Extension and Wall Shield Equivalents To determine the thickness required for any material when either the k or r values are known: T M = Thickness of material in inches k M = K value of desired material r M = R value of desired material T L = Mini ...
-
TOA Electronics RD-36 - page 18
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 18 Chimney Section 63L10 FTF8-12 63L13 FTF8-18 63L14 FTF8-36 63L15 FTF8-48 Canadian 62L92 FTF8-18C Chimney Section 62L93 FTF8-36C Take Off Boot 91L04 FATO Outside Combustion Air Kits (with duct) 81L87 FOAK (without duct) 81L88 FOAK-LD Secure the hearth extension to the floor to prevent possible shift ...
-
TOA Electronics RD-36 - page 19
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 19 63L38 F8F6 Flashing 63L39 F8F12 Round Termination 63L42 FTF8-CTD Chase Termination (Square) 63L48 FTF8-CT1 Firestop Spacer (Flat) 63L31 F8FS-2 Chase Termination (Round) 63L45 FTF8-CTDT Chase Termination (Square) 63L51 FTF8-CT2 Forced Air Blower Kits -Single Speed 80L84 FBK-100 -Variable Speed 80L8 ...
-
TOA Electronics RD-36 - page 20
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 20 Printed in U.S.A. © 2000 by LENNOX P/N 700,009M REV. D 11/2003 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code infor ...
У вас вопрос, касающийся TOA Electronics RD-36?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с TOA Electronics RD-36, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с TOA Electronics RD-36 со всей вероятностью он захочет поделиться методом ее решения.