-
Invacare 9000 - page 1
Ser vice Manual CLD CYCLIC AL LEVER DRIVE (9000 WHEELCHAIRS) ...
-
Invacare 9000 - page 2
2 WARNING W A R N I N G W ARNING DO NOT INST ALL THIS EQUIPMENT WITHOUT FIRST READING AND UNDERST ANDING THIS MANUAL AND THE 9000 WHEELCHAIR OWNER'S MANUAL (P AR T NUMBER 1056953) AND SER VICE MANUAL (P AR T NUMBER 1076155) . IF YOU ARE UNABLE TO UNDERST AND THE W ARNINGS, CAUTIONS, AND INSTRUCTIONS, CONT ACT A HEAL THCARE PROFESSIONAL, DEALER ...
-
Invacare 9000 - page 3
3 TABLE OF CONTENTS SAFETY SUMMAR Y ............................................................................................................................... .4 MAINTENANCE ....................................................................................................................................... 4 PROCEDURE 1 - ASSEMBL Y ......... ...
-
Invacare 9000 - page 4
4 SAFETY SUMMAR Y/MAINTENANCE S A F E T Y S U M M A R Y MAINTENANCE EVERY THREE (3) MONTHS Place a drop of oil on all linkage points (3-in-1 oil ® or equivalent). Inspect and tighten bolts if loosened. Clean chrome components with a soft cloth. ANNUALLY The CLD should be inspected by a qualified technician. M A I N T E N A N C E SAFETY SUMMARY NOT ...
-
Invacare 9000 - page 5
5 NOTE: The procedures in this manual should be per- formed on the specific side of the wheelchair the CLD was ordered for . ASSEMBLIES (FIGURE 1) The Cyclical Lever Device (CLD) consists of several as- semblies shown in FIGURE 1 and described on this page. For proper installation follow INST ALLING CLD ON EX- ISTING WHEELCHAIR in PROCEDURES 1-6 an ...
-
Invacare 9000 - page 6
6 F O R K A S S E M B L Y PROCEDURE 2 FORK ASSEMBL Y EXISTING FORK Front Caster FIGURE 1 - REMOVING FORK AND CASTER Locknut Front Caster Washers Hex Screw Fork REMOVING CASTER Locknut Dust Cover Front Caster and Fork Caster Headtube REMOVING EXISTING FORK Caster Headtube Caster Journal Cap Hex Nut Fork REMOVING CLD FORK CLD FORK Hex Screw Fork Remo ...
-
Invacare 9000 - page 7
7 Caster Size Seat-to-floor Caster Mounting Position Rear Wheel Size Rear Wheel Position 6 15.5 T op 20 *T op 6 16.5 Middle 22 * T o p 6 17.5 Bottom 24 *T op 6 17.5 Bottom 20 Bottom 8 17.5 T op 2 0 Bottom 8 17.5 T op 24 *T op 8 18.5 Middle 22 Bottom 8 19.5 Bottom 24 Bottom PROCEDURE 2 FIGURE 2 - MOUNTING CASTER TO CLD FORK ASSEMBL Y INSTALLING CLD ...
-
Invacare 9000 - page 8
8 R E A R W H E E L PROCEDURE 3 REAR WHEEL/TRANSMISSION T R A N S M I S S I O N REMOVING EXISTING WHEEL LOCK (FIGURE 1) 1. Remove the locknut and bolt securing the wheel lock to the wheelchair frame. 2. Remove the wheel lock from the wheelchair frame. INSTALLING CLD ON EXISTING WHEELCHAIR 1 . Remove the EXISTING wheel lock. Refer to REMOV- ING EXIS ...
-
Invacare 9000 - page 9
9 INSTALLING/REMOVING REAR WHEEL TO/FROM TRANSMISSION REAR HUB (FIGURE 4) Installing 1. Position rear wheel hub spokes in slots on transmis- sion rear hub. 2. Slide NEW axle bolt through rear wheel bearing. 3. Install hub support plates. Refer to INST ALLING/RE- MOVING THE HUB SUPPOR T PLA TES in this pro- cedure of the manual. Removing 1. If neces ...
-
Invacare 9000 - page 10
10 R E A R W H E E L T R A N S M I S S I O N Outer Hub Spacer Axle W asher Wheelchair Side Frame Pan Head Screw Rear Wheel Bearing Hub Support Plate Axle Bolt PROCEDURE 3 REAR WHEEL/TRANSMISSION INSTALLING/REMOVING THE AXLE BOLT (FIGURE 4) Installing 1. If necessary , install rear wheel onto transmission rear hub. Refer to INST ALLING/REMOVING THE ...
-
Invacare 9000 - page 11
11 This procedure includes the following: Installing CLD on Existing Wheelchair Replacing Support Bracket Replacing Drive Arm Assembly Mounting/Removing Support Bracket T o/From Wheelchair Removing/Installing Support Bracket T o/From Drive Arm Assembly Installing/Removing Drive Arm Assembly T o/From Transmission Installing/Removing Drive Arm Adjust ...
-
Invacare 9000 - page 12
12 Locknut Bolt (DO NOT remove) Spacer (DO NOT Remove) Support Bracket Mounting Hole Drive Arm Assembly Wheelchair Frame FIGURE 2 - REMOVING/INST ALLING SUPPORT BRACKET TO/FROM DRIVE ARM ASSEMBL Y D R I V E A R M DRIVE ARM/SUPPORT BRACKET REMOVING/INSTALLING SUPPORT BRACKET TO/FROM DRIVE ARM ASSEMBLY (FIGURE 2) Removing 1 . Remove the locknut secur ...
-
Invacare 9000 - page 13
13 PROCEDURE 4 INSTALLING/REMOVING DRIVE ARM ASSEMBLY TO/FROM TRANSMISSION (FIGURE 3) Installing 1. Secure the drive arm assembly to the transmission lever and wheel lock support bracket with hex screw , two (2) fender washers, shifter spacer and hex nut. T ighten securely . Removing 1. Remove the hex nut securing the hex screw to the transmission ...
-
Invacare 9000 - page 14
14 Wheelchairs Built AFTER 09/05/00 Wheelchairs Built BEFORE 09/05/00 Drive Arm Flat Surface Drive Arm Release Lever Plunger Extension T ube Button Button Screw Drive Arm Mounting Holes Mounting Hole (NOT Shown) Plunger T ube FIGURE 4 - INST ALLING/REMOVING DRIVE ARM - ADJUSTING DRIVE ARM RELEASE LEVER/ BRACKET RELEASE LEVER ADJUSTING DRIVE ARM REL ...
-
Invacare 9000 - page 15
15 Plunger T ube Mounting Hole (NOT Shown) Button Screw Drive Arm FIGURE 5- ADJUSTING DRIVE ARM HEIGHT Mounting Hole Wheelchairs Built AFTER 09/05/00 Wheelchairs Built BEFORE 09/05/00 Plunger T ube Mounting Hole Button Screw Drive Arm PROCEDURE 4 DRIVE ARM/SUPPORT BRACKET S U P P O R T B R A C K E T D R I V E A R M ...
-
Invacare 9000 - page 16
16 Mounting Hole Position for Flat Screws - Wheelchairs Built AFTER 09/05/00 Rear Wheel Hole-A Hole-B Hole-C Hole-D Size 20 X X 22 X X 24 X X Mounting Holes T ransmission Support Bracket This procedure includes the following: Installing CLD on Existing Wheelchair Replacing the CLD Wheel Lock Installing/Removing CLD Wheel Lock Adjusting Wheel Lock A ...
-
Invacare 9000 - page 17
17 W H E E L L O C K WHEEL LOCK PROCEDURE 5 FIGURE 2 - ADJUSTING WHEEL LOCK ASSEMBL Y POSITION Wheelchairs Built BEFORE 09/05/00 Flat Screws Wheel Lock Adjustment Rod Wheel Lock Support Bracket Wheelchairs Built AFTER 09/05/00 Flat Screws Wheel Lock Adjustment Rod T ransmission Support Bracket ADJUSTING WHEEL LOCK ENGAGEMENT POSITION (FIGURE 3 ) W ...
-
Invacare 9000 - page 18
18 FIGURE 3- ADJUSTING WHEEL LOCK ENGAGEMENT POSITION 1/4-INCH ENGAGEMENT Wheel Lock Block Outside Edge of Tire DET AIL "A" Drive Arm Shift Lever Knob Flat Screws Wheel Lock Adjustment Rod Rear Tire Wheelchairs Built AFTER 09/05/00 Wheelchairs Built BEFORE 09/05/00 1/4-INCH ENGAGEMENT Wheel Lock Block Outside Edge of Tire DET AIL "A& ...
-
Invacare 9000 - page 19
19 STEERING LINK PROCEDURE 6 FIGURE 1 - CONNECTING/REMOVING STEERING LINK TO/FROM FORK S T E E R I N G L I N K Steering Link Steering Pin (REMOVED) Fork Spring Straight Section Fork Hole INSTALLING CLD ON EXISTING WHEELCHAIR 1. Connect the steering link to the fork. Refer to CON- NECTING/REMOVING THE STEERING LINK T O/ FROM THE FORK in this procedu ...
-
Invacare 9000 - page 20
20 Steering Pin (INST ALLED) Steering Link Adjustment Nuts Steering Pin Rod End Steering Link Front Caster Drive Arm S T E E R I N G L I N K BALANCING THE STEERING LINK ALIGNING THE CASTER AND DRIVE ARM Steering Link Steering Link Adjustment Nuts Drive Arm Rod End Steering Pin Rod End Drive Arm Threads Steering Pin Threads NOTE: Threads are enlarge ...
-
Invacare 9000 - page 21
21 REMOVING/INSTALLING STEERING LINK (FIGURE 3) Removing 1. Remove the locknut and washer securing the rod end of the steering link to the bracket at the bottom of the drive arm assembly . 2. Remove the rod end from the drive arm assembly . Installing 1. Install the NEW rod end into the bracket at the bot- tom of the drive arm assembly . 2. Secure ...
-
Invacare 9000 - page 22
22 PROCEDURE 7 FRONT RIGGING This procedure includes the following: Installing CLD Front Rigging Release Handle W ARNING After ANY adjustments, repair or service and BE- FORE use, make sure all attaching har dware is tightened securely - otherwise injury or damage may result. INSTALLING CLD FRONT RIGGING RELEASE HANDLE (FIGURE 1) 1. Remove the two ...
-
Invacare 9000 - page 23
23 LIMITED WARRANTY PLEASE NOTE: THE W ARRANTY BELOW HAS BEEN DRAFTED TO COMPL Y WITH FEDERAL LA W APPLICABLE TO PRODUCTS MANUF ACTURED AFTER JUL Y 4, 1975. This warranty is extended only to the original pur chaser/user of our products. This warranty gives you specific legal rights and you may also have other legal rights which vary fr om state to ...
-
Invacare 9000 - page 24
Invacar e Corporation www .invacare.com USA Canada One Invacare W a y 5970 Chedw or th W ay Invacare is a registered trademark of Invacare Corporation. Elyria, Ohio USA Mississauga, Ontario © 1999 Invacare Corporation 44036-2125 L5R 3T9, Canada 800-333-6900 905-890-8838 Form No . 99-225 Part No. 1087937 R ev B (1) - 08/00 ...
У вас вопрос, касающийся Invacare 9000?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Invacare 9000, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Invacare 9000 со всей вероятностью он захочет поделиться методом ее решения.