-
Smeg SDR60XG3 - page 1
Index 1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 22 2. POSITIONING OF HOB ___________________________________ 24 3. ELECTRICAL CONNECTION ______________________________ 26 4. GAS CONNECTION ______________________________________ 27 5. ADAPTATION TO DIFFERENT TYPES OF GAS _______________ 29 6. FINAL OPERATIONS __________________________ ...
-
Smeg SDR60XG3 - page 2
Introduction 1. INSTRUCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN A N ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE C O OKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE SER IES OF NOZZLES S ...
-
Smeg SDR60XG3 - page 3
Introduction THE IDENTIFICATION PLATE, W ITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER TH E CASING. THE PLATE ON THE CASING MUST NOT BE R EMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE CASING. DO NOT PUT PANS WITHOUT PERFECTLY S ...
-
Smeg SDR60XG3 - page 4
Instructions for the installer 24 2. POSITIONING OF HOB The following operation r equires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). Never use silicone o ...
-
Smeg SDR60XG3 - page 5
Instructions for the installer 25 In case of installation on a hollo w compartment with doors, a separating panel has to be placed under the hob. Keep a minimum distance of 10 mm between the bottom of the uni t and the panel surface. The panel has to be easily removable to allow a ccess in the event of te chnical service. ...
-
Smeg SDR60XG3 - page 6
Instructions for the installer 26 3. ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate locat ed under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the curr ent electrical syste ...
-
Smeg SDR60XG3 - page 7
Instructions for the installer 27 4. GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the prov isions defi ned by standard regulations in force. To facilitate connection, fitting A on the r ear of the appliance may be adjusted laterally. For th is purpose, loosen hexagon nut B ...
-
Smeg SDR60XG3 - page 8
Instructions for the installer 28 Use a pressure regul ator and make the connection to the tank according to the provisions of standar d s regulations in force. Make sure that feed pressure conforms to the lev els shown in the table in paragraph “ 5.2 Regulation for LPG ”. 4.2 Ventilation of rooms The hob may be installed only in r ooms wit h p ...
-
Smeg SDR60XG3 - page 9
Instructions for the installer 29 5. AD APT A TION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspected for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other ty pes of gas the nozzles must be replaced and the prim ary air adj ...
-
Smeg SDR60XG3 - page 10
Instructions for the installer 30 5.2 Regulation for LPG Loosen screw A and push supp ort B all the way. Use a double head wrench to remove nozzle C and assemble the suitable one, followin g the instructions indicated in the reference charts, with respect to the type of gas to use. The screwing torque of the nozzle should nev er exceed 3 Nm . Repos ...
-
Smeg SDR60XG3 - page 11
Instructions for the installer 31 5.3 Regulation for natural gas The hob has been inspected for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work with this type of gas, perform the same operations describe d in paragraph “5.2 Regulation for LPG”, but choose the nozzles and regulate the primary air for natural gas, as show ...
-
Smeg SDR60XG3 - page 12
Instructions for the installer 32 6. FINAL OPERA TIONS Having carried out the abov e adjustments, reassemble the applianc e following, backwards, the instructions in paragraph “ 5.1 Removing the hob ”. 6.1 Regulation of minimum for natural gas Replace the compon ents on the burner and slide the knobs on the gas tap pins. Light the burner and se ...
-
Smeg SDR60XG3 - page 13
Instructions for the installer 33 6.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Rapid 4 Rapid 5 Ultra rapid 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-gr eased. This must be done by a qualified techn ician. ...
-
Smeg SDR60XG3 - page 14
Instructions for the user 34 7. USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted correctly. In the ultrarapid burner, notch A must be aligned with pin B . Grid C provided is intended for use with woks (Chinese pan s). Adapter D comes only with open grids models and is int ended for use wi ...
-
Smeg SDR60XG3 - page 15
Instructions for the user 7.2 Practical advice for usin g the burners For better burner performance an d minimum gas consumption, flat bottomed, even recipie nts must be used, with covers and proportiona l in size to the burners (see paragraph “ 7.3 Diameter of containers ”). To avoid overcooking or damage to the surface top w hile cooking, all ...
-
Smeg SDR60XG3 - page 16
Instructions for the user 36 7.5.2 Using the electric elements The electric elements are ideal for ultrarapid cooking. The settings shown in the table are merely indicativ e. POSITION HEAT INTENSITY POSSIBLE COOKING - 0 Off To melt butter, chocolate, etc. 1 Weak To heat small amounts of liquid. 2 Soft To heat larger amounts of liquid. To defrost fr ...
-
Smeg SDR60XG3 - page 17
Instructions for the user 8. CLEANING AND MAINTENANCE Before any intervention, disconnect the power supply of the device. 8.1 Cleaning Clean the cooking top regularly every time you use it, obviously after it has cooled. Never use a steam jet to clean the appliance. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve the su rface ...
-
Smeg SDR60XG3 - page 18
Instructions for the user 38 8.2 Cleaning of cooking hob componen ts CAUTION: do not wash these components in a dishwasher. In normal use of the hob, the stainless steel burner caps and pan-stands tend to be burnished by the high temp erature. Clean these parts using very fine abrasive sponges or similar c ommercial products. Then use a specific pa ...
У вас вопрос, касающийся Smeg SDR60XG3?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Smeg SDR60XG3, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Smeg SDR60XG3 со всей вероятностью он захочет поделиться методом ее решения.