Инструкция обслуживания Echo SRM - 2110

36 страниц 0.8 mb
Скачать

Перейти на страницу of 36

Summary
  • Echo SRM - 2110 - page 1

    Grass T rimmer/Brush Cutter Operator's Manual MODELS, SRM - 2100, 21 10 Serial Number 001001 & Up MODELS, T ype 1E SRM - 2100, 21 10 Serial Number 001001 & Up W ARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper ...

  • Echo SRM - 2110 - page 2

    2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the- job-dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages. W ARNING DANGER Read rules for saf ...

  • Echo SRM - 2110 - page 3

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 3 FRONT HANDLE (LOOP SHOWN) DRIVE SHAFT (W/DECALS) DEBRIS SHIELD (W/DECALS) CUTTING ATTACHMENT (NYLON BLADE SHOWN) STOP SWITCH POWER HEAD (W/DECALS) IMPORTANT The enclosed message provides information necessary for the protection of the unit. NOTE This enclosed message provides tips for ...

  • Echo SRM - 2110 - page 4

    4 SHAFT DECAL W ARNING DANGER • This unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the Operator's and Safety manuals. • Blindness can occur from objects that are thrown or ricocheted even with shield in place. Operators, helpers and bystande ...

  • Echo SRM - 2110 - page 5

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 5 EQUIPMENT Before operation a complete check of the unit must be performed; • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found. • Insp ...

  • Echo SRM - 2110 - page 6

    6 PERSONAL CONDITION AND SAFETY EQUIPMENT W ARNING DANGER Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a trimmer. Physical Condition -- Your judgment and physical dexterity may not ...

  • Echo SRM - 2110 - page 7

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 7 15M (50 ft.) SAFE OPERA TION Determine Operation Area - Provide all operators of this equipment with the operator's manual and instructions for safe operation. - Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions. - Spectators and fellow wor ...

  • Echo SRM - 2110 - page 8

    8 Vibration and Cold -- It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers. The following precautions are ...

  • Echo SRM - 2110 - page 9

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 9 Contents List Items 1 - Power Head 1 - Drive Shaft Assembly 1 - Plastic Bag (co-pack) - 1, Operator's Manual - 1, Safety Manual - 1, Warranty Registration Card - 1, Limited Warranty Statement - 1, Plastic shield - 1, Tool Bag --1, 8mm x 10mm wrench --1, scrench --1, locking tool - ...

  • Echo SRM - 2110 - page 10

    10 1 SAFETY VIDEO 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 26 EMISSION CONTROL -- The emission control system for this engine is EM (Engine Modification). Emission Control Label located on Engine (EXAMPLE ONLY, information on label varies by FAMILY). 5 21 22 23 24 25 IMPORT ANT ENGINE INFORMA TION ENGINE F AMIL Y : TEH021UB24RA DISPLACEMENT ...

  • Echo SRM - 2110 - page 11

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 11 1. OPERATOR'S MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference, i.e., operation, maintenance, storage and specifications. 2. SAFETY MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe ...

  • Echo SRM - 2110 - page 12

    12 S PECIFICA TIONS SRM-2100, 2110 1/1E * Install and use U-Handle when operating any model with blade. L E D O ME 1 / 1 0 0 1 2E 1 / 1 0 1 1 2 h t g n e L ) . n i 9 5 ( m m 0 0 5 1) . n i 9 5 ( m m 0 0 5 1 h t d i W ) . n i 0 . 3 1 ( m m 0 3 3) . n i 6 . 3 2 ( m m 0 0 6 t h g i e H ) . n i 8 . 1 1 ( m m 0 0 3) . n i 2 . 4 1 ( m m 0 6 3 d a e h r e ...

  • Echo SRM - 2110 - page 13

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 13 PLASTIC SHIELD INST ALLA TION (for Nylon Line Operation) Tools Required: Screwdriver. Parts Required: Plastic Shield, Shield Plate, three (3) 5mm x 15mm screws. NOTE The plastic shield is for use with the Nylon Line Head only. Install Metal Shield when using plastic or metal blades. 1 ...

  • Echo SRM - 2110 - page 14

    14 BLADE INST ALLA TION All Models. IMPORTANT If non-standard monofilament head, METAL/PLASTIC blade or cultivator etc. is used, THE CARBURETOR MUST BE RE-SET or serious engine damage may occur. See "Carburetor Adjustment" pages 29 - 30 and "Specifications" page 12 of this manual. W ARNING DANGER You must install a U-Handle Kit ...

  • Echo SRM - 2110 - page 15

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 15 Install Harness Clamp NOTE Some models require installation of Harness Clamp. If your unit does not have a clamp, follow these directions. Tools Required: Screwdriver, 8mm x 10mm Open End Wrench. Parts Required : Clamp, 4mm x 18mm Hexagon Head, Bolt, Link. 6. Remove shield and gear ho ...

  • Echo SRM - 2110 - page 16

    16 THROTTLE LINKAGE AND IGNITION LEADS Tools Required: 8mm x 10mm open end wrench (all models), 3mm Allen Wrench. 1. Close choke and remove air filter cover. 2. Loosen nut (A) and place threaded end of throttle linkage in bracket slot. Finger tighten nut (A). 3. Place inner cable in slot of carburetor swivel (B) and tighten nut (A). 4. Check thrott ...

  • Echo SRM - 2110 - page 17

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 17 U - HANDLE INST ALLA TION Tools Required : 8mm x 10mm Open End Wrench, Slotted Screw- driver, (3mm Hex Wrench SRM-2100 only.) Parts Required: U-Handle Kit. (SRM-2100) P/N 35130454130 NOTE On model SRM-2110 use Steps 1, 10, 11 and 13 - 17 only. 1. Close choke and remove air filter cove ...

  • Echo SRM - 2110 - page 18

    18 1 1 . Secure throttle linkage and leads to drive shaft with cable clips supplied. 12. Install power head and align gear box, power head and U-handles. Tighten all screws. 1 3 . Place throttle linkage in slot in bracket with one nut (A) and washer on each side of bracket. Finger tighten both nuts (A). 14. Attach inner throttle cable to swivel (B) ...

  • Echo SRM - 2110 - page 19

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 19 Plastic and Nylon Blades Require "Blade Conversion Kit," P/N 99922200410 (metal shield and shoulder harness). Steel/Metal Blades Require "Blade Conversion Kit" PLUS a "U-Handle Kit." P/N 35130454130 or Combination Blade Kit and "U-Handle Kit" P/ ...

  • Echo SRM - 2110 - page 20

    20 8 Tooth Weed/Grass Blade P/N 69600120331 is designed for grass, garden debris and thick weeds. DO NOT use this blade for brush or heavy woody growth, 3/4" in. (19 mm) diameter or larger. Brush/Clearing Blade P/N 69500120331 is designed for cutting brush and woody growth up to 76 mm (3" in.) diameter. Use Shoulder/Waist Harness P/N 9994 ...

  • Echo SRM - 2110 - page 21

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 21 SM T W T F S 1234 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 R + M 2 3 M (10 FT.) MINIMUM FUEL Fuel Requirements Gasoline - Use 89 Octane [ ] gasoline or gasohol known to be good quality. Gasohol may contain up to 10% Ethyl (grain) alcohol or 15% MTBE ...

  • Echo SRM - 2110 - page 22

    22 15M (50 ft.) IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. IMPORTANT Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use. EQUIPMENT CHECK Before operation a complete check of the unit must be performed; • Che ...

  • Echo SRM - 2110 - page 23

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 23 O PERA TION - Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. - Before starting the unit, equip yourself and any other person working within the 15M (50 ft.) Safety Zone with the required Protective Equipment and clothing. - ...

  • Echo SRM - 2110 - page 24

    24 5 . After engine fires (or five [5] pulls) move choke lever to “Run” position. Hold throttle trigger fully depressed and pull recoil starter handle/rope (D) until engine starts and runs. Release throttle trigger and allow unit to warm up at idle for several minutes. NOTE If engine does not start with choke in “Run” position after 4 pulls ...

  • Echo SRM - 2110 - page 25

    G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 2 5 MAINTENANCE INTER V ALS / T N E N O P M O C M E T S Y S E C N A N E T N I A M E R U D E C O R P D ' Q E R L L I K S L E V E L R O Y L I A D E R O F E B E S U Y R E V E L E U F E R 3 S H T N O M 0 9 R O S R U O H 6 S H T N O M 0 7 2 R O S R U O H Y L R A E Y 0 0 6 S R U O H s e r u ...

  • Echo SRM - 2110 - page 26

    26 AIR FIL TER Level 1. Tools required: Cleaning Brush Parts required: 90008 REPOWER AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from the air cleaner area. 2. Remove the air cleaner cover. Clean and inspect the element ...

  • Echo SRM - 2110 - page 27

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 27 SP ARK PLUG Level 2. Tools required: Scrench (combination socket wrench and screw driver supplied with unit), Feeler gauge (preferably a wire gauge), Soft metal brush Parts Required: Spark Plug NGK BPMR-7A 1. Remove spark plug and check for fouling, worn and rounded center electrode. ...

  • Echo SRM - 2110 - page 28

    28 NOTE The throttle linkage remains assembled to the cover and the spark plug lead and grommet remain installed. 3. Use the wooden stick or brush to remove dirt form cylinder fins. 4. Remove grass and leaves from the grid between the recoil starter and fuel tank. 5. Assemble components in reverse order. NOTE When installing the cover, be certain t ...

  • Echo SRM - 2110 - page 29

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 29 CARBURETOR ADJUSTMENT Type 1E Emission Models Level 2. Tools required: Slotted Screwdriver w/2 mm blade width, Tachom- eter (ECHO P/N 99051130017) Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compliance with EPA Phase 1 and California Emissi ...

  • Echo SRM - 2110 - page 30

    30 B A C (1) (3) (4) (2) CARBURETOR ADJUSTMENT Type 1 Non Emission Models Idle Speed Adjustment NOTE If carburetor has limiter caps follow "Carburetor Adjustment" procedures for Type 1E models on previous page. Turn "idle" speed adjustment screw (C) CW (clockwise) until cutting attachment begins to turn, then turn screw out CCW ...

  • Echo SRM - 2110 - page 31

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 31 A B B C LUBRICA TION Level 1. Tools required: 8 mm Open End Wrench, Cross Head Screwdriver, Clean rag Parts Required: Lithium Base Grease. Gear Housing 1. Clean all loose debris from gear box. 2. Remove plug (A) and check level of grease. 3. Add grease if necessary, DO NOT over fill. ...

  • Echo SRM - 2110 - page 32

    32 A B D C E D G E B H F A B 1 . Hold drum (A) and turn spool (B) CW (clockwise) until it stops. Pull spool from drum. DO NOT push in on spool when turning. 2. Use one piece of new nylon line (C) 40 ft. (12m) long and thread through the molded loop (D) on the spool. Pull line tight and adjust so one end is 15 cm (6 in.) longer than the other. 3. Ho ...

  • Echo SRM - 2110 - page 33

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 33 SHARPENING MET AL BLADES Three styles of metal blades are approved for use on the ECHO Brush Cutter. The 8-tooth blade can be sharpened during normal mainte- nance. The clearing blade and 80 tooth blade require professional service. Before sharpening, CLOSELY inspect blade for cracks ...

  • Echo SRM - 2110 - page 34

    34 Remedy Muffler wet with fuel Engine does not crank No fuel at cylinder Spark at end of plug wire No spark at end of plug wire Spark at plug No spark at plug Engine Cranks Fuel at carburetor No fuel at carburetor Open choke Clean/replace air filter Adjust carburetor See your Echo dealer Stop switch off Electrical problem Interlock switch Fuel mix ...

  • Echo SRM - 2110 - page 35

    G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 35 S T ORA GE Long term storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1. Store unit in a dry, dust free place, out of the reach of children. W ARNIG DANGER D ...

  • Echo SRM - 2110 - page 36

    ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 DEALER? Call 1-800-432-ECHO 1-800-432-(3246) ECHO Incorporated 400 Oakwood Road Lake Zurich, IL 60047 Technical Publications Orders S ERVICING I NFORMA TION P ARTS -- Genuine ECHO Parts and ECHO REPPWER Parts and Assemblies for your ECHO products are available only from an Authorized E ...

Производитель Echo Категория Brush Cutter

Документы, которые мы получаем от производителя устройства Echo SRM - 2110 мы можем разделить на несколько групп. Это в частности:
- технические чертежи Echo
- инструкции обслуживания SRM - 2110
- паспорта изделия Echo
- информационные брошюры
- энергетические этикетки Echo SRM - 2110
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Echo SRM - 2110.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Echo SRM - 2110, инструкции обслуживания, короткие инструкции или инструкции пользователя Echo SRM - 2110. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Echo SRM - 2110.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Echo SRM - 2110, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Echo SRM - 2110 пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Echo SRM - 2110.

Полная инструкция обслуживания Echo, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Echo SRM - 2110 - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Echo SRM - 2110, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Echo SRM - 2110, которое найдем в данном документе
3. Советы по использованию основных функций устройства Echo SRM - 2110 - которые должны облегчить нам первые шаги во время использования Echo SRM - 2110
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Echo SRM - 2110
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Echo SRM - 2110 в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Echo SRM - 2110?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Echo SRM - 2110, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Echo SRM - 2110 со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Комментарии (0)