Русский dropdown-ico

Инструкция обслуживания Goldline LOGIC PL-P-4

36 страниц 1.48 mb
Скачать

Перейти на страницу of 36

Summary
  • Goldline LOGIC PL-P-4 - page 1

    Pro Logic Programming Flow Chart North Kingstown, RI 02852 USA 092337C Copyright © 2009 Goldline Controls www .goldlinecontrols.com Automation and Chlorination Inst allation Manual for model PL-P-4 LD C G LI N E ON T ROLS LD C G LI N E ON T ROLS denot es cond itiona l item s def ault m e nu day a nd tim e wa ter temperat ure air t emperatur e chlo ...

  • Goldline LOGIC PL-P-4 - page 2

    IMPORT ANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: • READ AND FOLLOW ALL INSTRUCTIONS • ! W ARNING: Disconnect all AC power during inst allation. • ! W ARNING: W ater in excess of 100 degrees Fahrenheit may be hazardous to your health. • ! W ARNIN ...

  • Goldline LOGIC PL-P-4 - page 3

    T able of Content s Introduction Before Y ou Begin................................................................... 1 Installation S teps.................................................................... 2 1. Preparing General W ater Chemistry ..................................................... 2 Pool/Sp a W ater Salt......................... ...

  • Goldline LOGIC PL-P-4 - page 4

    Introduction Before Y ou Begin What’s Included Before attempting to install the Pro Logic system, check that the following components have been included in the package: Pr o Logic Electr onics Unit (3) T emperature sensors with 15 ft. (5m) cable, hose clamp What’s NOT Included Some of the additional items that you may need to complete an instal ...

  • Goldline LOGIC PL-P-4 - page 5

    4. Electrical W iring (page 10) Main service Grounding and bonding Circuit breakers Pro Logic control power High V oltage pool equipment Low voltage wiring (temperature sensors, flow switch, etc.) 2 29 ºC º F Ti Calcuim Hardne ss Ci To t a l Alkalinity Ai 53 60 66 76 84 94 103 12 16 19 24 29 34 39 .3 .4 .5 .6 .7 .8 .9 How to use: Measure pool p H ...

  • Goldline LOGIC PL-P-4 - page 6

    Gall o n s a n d ( L i t e r s ) o f P o o l / S p a w a t e r 12,0 00 14 ,00 0 16,0 00 1 8 , 0 0 0 2 0 , 0 0 0 2 2 , 0 0 0 3 2 , 0 0 0 2 4 , 0 0 0 3 4 , 0 0 0 2 6 , 0 0 0 3 6 , 0 0 0 2 8 , 0 0 0 3 8 , 0 0 0 3 0 , 0 0 0 4 0 , 0 0 0 Current salt level (45000) (52,500 ) (60,000) ( 6 7 , 5 0 0 ) ( 7 5 , 0 0 0 ) ( 8 2 , 5 0 0 ) ( 1 2 0 , 0 0 0 ) ( 9 0 ...

  • Goldline LOGIC PL-P-4 - page 7

    4 Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super Chlorinate cycle when the Aux button is pressed, rather than using the Settings Menu. Note that only one button can be assigned to this function. Aux1 Relay This feature allows the user to select either “Standard” (default) or “Dimmer” type ...

  • Goldline LOGIC PL-P-4 - page 8

    2. Mounting the Equipment Pro Logic Control Center The Pro Logic is contained in a raintight enclosure that is suitable for outdoor mounting. The control must be mounted a minimum of 5 ft. (2 meters) horizontal distance from the pool/spa (or more, if local codes require). The Control Center is designed to mount vertically on a flat surface with the ...

  • Goldline LOGIC PL-P-4 - page 9

    Optional AQL-CHEM2 CO 2 Dispensing Kit The AQL-CHEM2 is a CO 2 dispensing device that connects directly to the Pro Logic. When used with an AQL- CHEM, the Pro Logic will sense the pool’ s pH level and automatically dispense the correct amount of CO 2 to control the pool’ s pH to the desired level. W iring and plumbing requirements for the AQL-C ...

  • Goldline LOGIC PL-P-4 - page 10

    Wireless Remote Controls Note that the Pro Logic is compatible with AQL2 wireless remote controls only . A single AQL2-BASE-RF Base S tation must be installed on the Pro Logic in order to use any of the Goldline wireless remote controls. W ith the Base Station installed, there is no limit on the number of wireless remotes that can used. The maximum ...

  • Goldline LOGIC PL-P-4 - page 11

    3. Plumbing Pool/Sp a system configuration These systems use a single filter pump and filter . Pool or spa operation is controlled by two 3-way valves (suction and return). Refer to the diagram below . Some important notes regarding the Pro Logic control of Standard Pool/Spa systems: In Pool/Spa Config., select: Po o l / S p a S e t up Po o l a n d ...

  • Goldline LOGIC PL-P-4 - page 12

    T urbo Cell (choose proper model for your pool) The T urbo Cell (used for chlorine generation) should be plumbed AFTER the filter and heater . If installed on a pool/ spa combination system, the cell should be plumbed BEFORE the pool/spa return valve in order to allow proper chlorination of both the pool and the spa. Refer to plumbing diagram below ...

  • Goldline LOGIC PL-P-4 - page 13

    4. Electrical Wiring The Pro Logic Control Center requires both high and low voltage connections. Low voltage connections will be made to actuators, sensors, remote keypad, etc. High voltage connections will be made to pumps, lights, etc., as well as providing direct input power to the Control Center . Always: -Ensure that Power is disconnected pri ...

  • Goldline LOGIC PL-P-4 - page 14

    General Purpose Outlet If desired, a duplex receptacle with weatherproof cover (supplied by installer) may be installed in the knockouts on the lower right side of the Pro Logic enclosure. Per code, the receptacle should be a GFCI type. Alternatively , connect a standard receptacle to a GFCB. Pro Logic Control Power The Pro Logic requires 120V AC, ...

  • Goldline LOGIC PL-P-4 - page 15

    ! W ARNING: Do not use the Pro Logic to control an automatic pool cover . Swimmers may become entrapped underneath the cover . T wo speed filter pump: Requires 2 relays (FIL TER plus one of the AUX relays) for proper operation of both speeds. ! IMPOR T ANT : Be sure to follow the wiring diagram below AND to configure the contr ol logic according to ...

  • Goldline LOGIC PL-P-4 - page 16

    Low V olt age Wiring V alve Actuators The Pro Logic can control up to three automatic valve actuators. T wo of the valve outputs are dedicated to the pool/ spa suction (V alve2) and return (V alve1) valves. V alve3 is for general purpose use (solar , water feature, in-floor cleaner , etc.). For installations with solar heating, Goldline of fers the ...

  • Goldline LOGIC PL-P-4 - page 17

    Laars Heaters 1. Turn power of f to heater . 2. Remove factory jumper from terminal block. 3. W ire Pro Logic to the heater as shown. 4. Ensure toggle switch is in the ON position. 5. Set heater thermostats to maximum position. to l imi t s wit che s remov e jumper Fusi bl e Link whit e whi t e Hayward Heaters Refer to the instructions in the heate ...

  • Goldline LOGIC PL-P-4 - page 18

    Pentair/Purex/MiniMax 1. T urn power off to heater . 2. Remove factory installed jumper from the “Ext Switch” connector . 3. W ire the Pro Logic to the “Ext Switch” connector as shown below . 4. The wires to the Pro Logic must be separated from any line voltage wires. Failure to follow these instructions may cause erratic operation of the h ...

  • Goldline LOGIC PL-P-4 - page 19

    Pentair/Purex/MiniMax 1. T urn power off to heater . 2. Remove factory installed jumper from the “Ext Switch” connector . 3. W ire the Pro Logic to the “Ext Switch” connector as shown below . 4. The wires to the Pro Logic must be separated from any line voltage wires. Failure to follow these instructions may cause erratic operation of the h ...

  • Goldline LOGIC PL-P-4 - page 20

    Laars Heaters 1. Turn power of f to heater . 2. Remove factory jumper from terminal block. 3. W ire Pro Logic to the heater as shown. 4. Ensure toggle switch is in the ON position. 5. Set heater thermostats to maximum position. to l imi t s wit che s remov e jumper Fusi bl e Link whit e whi t e Hayward Heaters Refer to the instructions in the heate ...

  • Goldline LOGIC PL-P-4 - page 21

    Low V olt age Wiring V alve Actuators The Pro Logic can control up to three automatic valve actuators. T wo of the valve outputs are dedicated to the pool/ spa suction (V alve2) and return (V alve1) valves. V alve3 is for general purpose use (solar , water feature, in-floor cleaner , etc.). For installations with solar heating, Goldline of fers the ...

  • Goldline LOGIC PL-P-4 - page 22

    ! W ARNING: Do not use the Pro Logic to control an automatic pool cover . Swimmers may become entrapped underneath the cover . T wo speed filter pump: Requires 2 relays (FIL TER plus one of the AUX relays) for proper operation of both speeds. ! IMPOR T ANT : Be sure to follow the wiring diagram below AND to configure the contr ol logic according to ...

  • Goldline LOGIC PL-P-4 - page 23

    General Purpose Outlet If desired, a duplex receptacle with weatherproof cover (supplied by installer) may be installed in the knockouts on the lower right side of the Pro Logic enclosure. Per code, the receptacle should be a GFCI type. Alternatively , connect a standard receptacle to a GFCB. Pro Logic Control Power The Pro Logic requires 120V AC, ...

  • Goldline LOGIC PL-P-4 - page 24

    4. Electrical Wiring The Pro Logic Control Center requires both high and low voltage connections. Low voltage connections will be made to actuators, sensors, remote keypad, etc. High voltage connections will be made to pumps, lights, etc., as well as providing direct input power to the Control Center . Always: -Ensure that Power is disconnected pri ...

  • Goldline LOGIC PL-P-4 - page 25

    T urbo Cell (choose proper model for your pool) The T urbo Cell (used for chlorine generation) should be plumbed AFTER the filter and heater . If installed on a pool/ spa combination system, the cell should be plumbed BEFORE the pool/spa return valve in order to allow proper chlorination of both the pool and the spa. Refer to plumbing diagram below ...

  • Goldline LOGIC PL-P-4 - page 26

    3. Plumbing Pool/Sp a system configuration These systems use a single filter pump and filter . Pool or spa operation is controlled by two 3-way valves (suction and return). Refer to the diagram below . Some important notes regarding the Pro Logic control of Standard Pool/Spa systems: In Pool/Spa Config., select: Po o l / S p a S e t up Po o l a n d ...

  • Goldline LOGIC PL-P-4 - page 27

    Wireless Remote Controls Note that the Pro Logic is compatible with AQL2 wireless remote controls only . A single AQL2-BASE-RF Base S tation must be installed on the Pro Logic in order to use any of the Goldline wireless remote controls. W ith the Base Station installed, there is no limit on the number of wireless remotes that can used. The maximum ...

  • Goldline LOGIC PL-P-4 - page 28

    Optional AQL-CHEM2 CO 2 Dispensing Kit The AQL-CHEM2 is a CO 2 dispensing device that connects directly to the Pro Logic. When used with an AQL- CHEM, the Pro Logic will sense the pool’ s pH level and automatically dispense the correct amount of CO 2 to control the pool’ s pH to the desired level. W iring and plumbing requirements for the AQL-C ...

  • Goldline LOGIC PL-P-4 - page 29

    2. Mounting the Equipment Pro Logic Control Center The Pro Logic is contained in a raintight enclosure that is suitable for outdoor mounting. The control must be mounted a minimum of 5 ft. (2 meters) horizontal distance from the pool/spa (or more, if local codes require). The Control Center is designed to mount vertically on a flat surface with the ...

  • Goldline LOGIC PL-P-4 - page 30

    4 Super Chlorinate – if “Chlorinator” is enabled, this option allows the user to start a Super Chlorinate cycle when the Aux button is pressed, rather than using the Settings Menu. Note that only one button can be assigned to this function. Aux1 Relay This feature allows the user to select either “Standard” (default) or “Dimmer” type ...

  • Goldline LOGIC PL-P-4 - page 31

    Gall o n s a n d ( L i t e r s ) o f P o o l / S p a w a t e r 12,0 00 14 ,00 0 16,0 00 1 8 , 0 0 0 2 0 , 0 0 0 2 2 , 0 0 0 3 2 , 0 0 0 2 4 , 0 0 0 3 4 , 0 0 0 2 6 , 0 0 0 3 6 , 0 0 0 2 8 , 0 0 0 3 8 , 0 0 0 3 0 , 0 0 0 4 0 , 0 0 0 Current salt level (45000) (52,500 ) (60,000) ( 6 7 , 5 0 0 ) ( 7 5 , 0 0 0 ) ( 8 2 , 5 0 0 ) ( 1 2 0 , 0 0 0 ) ( 9 0 ...

  • Goldline LOGIC PL-P-4 - page 32

    4. Electrical W iring (page 10) Main service Grounding and bonding Circuit breakers Pro Logic control power High V oltage pool equipment Low voltage wiring (temperature sensors, flow switch, etc.) 2 29 ºC º F Ti Calcuim Hardne ss Ci To t a l Alkalinity Ai 53 60 66 76 84 94 103 12 16 19 24 29 34 39 .3 .4 .5 .6 .7 .8 .9 How to use: Measure pool p H ...

  • Goldline LOGIC PL-P-4 - page 33

    Introduction Before Y ou Begin What’s Included Before attempting to install the Pro Logic system, check that the following components have been included in the package: Pr o Logic Electr onics Unit (3) T emperature sensors with 15 ft. (5m) cable, hose clamp What’s NOT Included Some of the additional items that you may need to complete an instal ...

  • Goldline LOGIC PL-P-4 - page 34

    T able of Content s Introduction Before Y ou Begin................................................................... 1 Installation S teps.................................................................... 2 1. Preparing General W ater Chemistry ..................................................... 2 Pool/Sp a W ater Salt......................... ...

  • Goldline LOGIC PL-P-4 - page 35

    IMPORT ANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: • READ AND FOLLOW ALL INSTRUCTIONS • ! W ARNING: Disconnect all AC power during installation. • ! W ARNING: W ater in excess of 100 degrees Fahrenheit may be hazardous to your health. • ! W ARNING ...

  • Goldline LOGIC PL-P-4 - page 36

    Pro Logic Programming Flow Chart North Kingstown, RI 02852 USA 092337C Copyright © 2009 Goldline Controls www .goldlinecontrols.com Automation and Chlorination Inst allation Manual for model PL-P-4 LD C G LI N E ON T ROLS LD C G LI N E ON T ROLS denot es cond itiona l item s def ault m enu day a nd tim e wa ter temperat ure air t emperatur e chlor ...

Производитель Goldline Категория CD Player

Документы, которые мы получаем от производителя устройства Goldline LOGIC PL-P-4 мы можем разделить на несколько групп. Это в частности:
- технические чертежи Goldline
- инструкции обслуживания LOGIC PL-P-4
- паспорта изделия Goldline
- информационные брошюры
- энергетические этикетки Goldline LOGIC PL-P-4
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Goldline LOGIC PL-P-4.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Goldline LOGIC PL-P-4, инструкции обслуживания, короткие инструкции или инструкции пользователя Goldline LOGIC PL-P-4. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Goldline LOGIC PL-P-4.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Goldline LOGIC PL-P-4, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Goldline LOGIC PL-P-4 пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Goldline LOGIC PL-P-4.

Полная инструкция обслуживания Goldline, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Goldline LOGIC PL-P-4 - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Goldline LOGIC PL-P-4, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Goldline LOGIC PL-P-4, которое найдем в данном документе
3. Советы по использованию основных функций устройства Goldline LOGIC PL-P-4 - которые должны облегчить нам первые шаги во время использования Goldline LOGIC PL-P-4
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Goldline LOGIC PL-P-4
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Goldline LOGIC PL-P-4 в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Goldline LOGIC PL-P-4?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Goldline LOGIC PL-P-4, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Goldline LOGIC PL-P-4 со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)