-
Shindaiwa X7502825900 - page 1
C254 BR USHCUTTER SHIND AIWA O WNER’S/OPERA T OR’S MANU AL WARNING! Minimize the risk of injury to yourself and oth- ers! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit. X7502825900 06/10 ...
-
Shindaiwa X7502825900 - page 2
2 The Shindaiwa H4 series of hand-held power equipment is designed and built to deliver superior performance and reliability without compromise to quality , comfort, safety or durability . Shindaiwa engines represent the leading edge of high-performance engine technology , delivering exceptionally high power with remarkably low displacement and wei ...
-
Shindaiwa X7502825900 - page 3
3 AL W A YS inspect unit before each use. Replace any damaged parts. NEVER run the engine when trans- porting the unit. NEVER run the engine indoors! Make sure there is always good ventila- tion. Fumes from engine exhaust can cause serious injury or death. AL W A YS stop the unit immediately if it suddenly begins to vibrate or shake. Inspect for br ...
-
Shindaiwa X7502825900 - page 4
4 Be Aware of the Wor king En vironment Avoid long-term operation in very hot or very cold weather . Make sure bystanders or observers outside the 15 meter (50 feet) “danger zone” wear eye protection. Be extremely careful of slippery terrain, especially during rainy weather . If contact is made with a hard object, stop the engine and inspect th ...
-
Shindaiwa X7502825900 - page 5
5 Product Description Using the illustration as a guide, familiarize yourself with your machine and its various com- ponents. Understanding your machine helps ensure top perfor- mance, long service life and safer operation. WARNING! Do not make unauthorized modications or alterations to any of these units or their components. Specications Out ...
-
Shindaiwa X7502825900 - page 6
6 Assembly Prior to Assembly Before assembling, make sure you have all the components required for a complete unit and inspect unit and components for any damage. Engine/Outer tube assembly ■ Handlebar and Throttle assembly ■ Cutting attachment shields ■ This unit comes fully assembled with the exception of the handlebar , cut- ting attachmen ...
-
Shindaiwa X7502825900 - page 7
7 NOTE: The plastic shield is for use with the Nylon Line Head only . Install Metal Shield when using plastic or metal blades. 1. Remove plastic threaded shaft sleeve and adapter plate (C) from PTO shaft (A). 2. Place the shield on the bottom of the bearing housing ange. 3. Place shield plate (B) on shield, align holes. Install three (3) screws ...
-
Shindaiwa X7502825900 - page 8
8 4-6 mm (3/16”-1/4”) Throttle Free Play Remove air cleaner cover Assembly (continued) Adjust throttle trigger free play The throttle trigger free play should be approximately 4 - 6 mm (3/16” - 1/4”). Make sure that the throttle lever operates smoothly without binding. Loosen the air cleaner cover 1. knob(s) and remove the air cleaner cover ...
-
Shindaiwa X7502825900 - page 9
9 The unit should now be completel y assembled and ready for use with a blade. IMPORT ANT! Discard blades that are bent, warped, cracked, broken or damaged in any way . Use a sharp blade. A dull blade is more likely to snag and thrust. C J I F d. Remove three screws holding shield plate (E) and plastic shield (C) to gear housing. e. Retain line hea ...
-
Shindaiwa X7502825900 - page 10
10 W ARNING! Alternative fuels, such as E15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting Shindaiwa requirements are NOT approved for use in Shindaiwa gasoline engines. Use of alternative fuels may cause performance problems, loss of power , overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, ...
-
Shindaiwa X7502825900 - page 11
11 NEVER ■ smoke or light res near the engine. AL W A YS ■ stop the engine and allow it to cool before refueling. A LWA Y S ■ Wipe all spill ed fu el an d mov e at least 3 me ters (10 f eet) from the fuel ing p oint and s ource befo re starting. NEVER ■ place ammable material close to the engine mufer . NEVER ■ operate the engine ...
-
Shindaiwa X7502825900 - page 12
12 Make sure the attachment is clear of obstructions! ...and pull recoil starter handle upward Hold the unit rmly ... Open After engine starts, move choke to OPEN position Close choke Set the choke lever to the CLOSED position Star ting the Engine IMPORT ANT! Engine ignition is controlled by a two position switch mounted on the throttle housing ...
-
Shindaiwa X7502825900 - page 13
13 After the engine starts, allow the ■ engine to warm up at idle 2 or 3 minutes before operating the unit. W hen the Engine Star ts... After the engine is warm, pick up ■ the unit and clip on the shoulder strap, if so equipped. NEVER operate the unit with the cut - ting attachment shield or other protec - tive devices removed! Use only authori ...
-
Shindaiwa X7502825900 - page 14
14 Y our Shindaiwa unit may be equipped with one of several Shindaiwa trimmer head models, each with features for specic applications and/or operational requirements. Cutting gr ass with a trimmer head T rimmer head styles: Semi-automatic . T rimmer line is indexed when the operator taps the trimmer head on the ground during operation. Manual . ...
-
Shindaiwa X7502825900 - page 15
15 D O N O T C U T Using a blade Blade T hrust “Blade thrust” is a sudden sideways or backward motion of the brushcutter . Such motion may occur when the blade jams or catches on an object such as a sapling tree or tree stump. BE CONST ANTL Y ALERT FOR BLADE THRUST AND GUARD AGAINST ITS EFFECTS! Br ushcutter Shoulder Strap A shoulder strap prov ...
-
Shindaiwa X7502825900 - page 16
16 Prior to each work day , perform the following: Remove all dirt and debris from the ■ engine, check the cooling ns and air cleaner for clogging, and clean as necessary . Carefully remove any accumulations ■ of dirt or debris from the mufer and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build- ...
-
Shindaiwa X7502825900 - page 17
17 Remove and inspect the pre-lter . 2. If the pre-lter is torn or otherwise damaged, replace it with a new one. Clean the pre-lter with soap and 3. water . Let dry before reinstalling. Inspect the air lter element. If the 4. element is damaged or distorted, replace it with a new one. T ap lter gently on a hard surface to 5. dislodge ...
-
Shindaiwa X7502825900 - page 18
18 Combustion chamber should be decarbonized, and the valve clearance should be adjusted. It is highly recommended ■ that this is done by a Shindaiwa-trained service technician. Replace the spark plug annually: Use only the type recommended in the ”Specications” section or an equivalent resis - ■ tor type spark plug of the correct heat r ...
-
Shindaiwa X7502825900 - page 19
19 Engine Cover Screws Engine Cover Mufer Mufer Gasket Mufer Bolts Spark Arrester Screen Spark Arrester Cover Cover Screws Mufer and spar k ar rester maintenance With a 3 mm hex wrench remove the 1. engine cover screws and the engine cover . If the engine becomes sluggish and low on power , check and clean the spark arrester screen. IMP ...
-
Shindaiwa X7502825900 - page 20
20 WARNING! Sharpen only the cutting teeth of a blade. DO NOT alter the contour of the blade in any way . WARNING! Wear protective gloves when handling or performing main- tenance on the blade. Round File When the cutting edges of the blade become dull, they can be resharpened with a few strokes of a le. In order to keep the blade in balance, al ...
-
Shindaiwa X7502825900 - page 21
21 Long T er m Stor age Remove the spark plug and pour about 1/4 ounce of 2-cycle mixing oil into the cylinder through the spark plug hole. ■ Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug. Before storing the unit, repair or replace any worn or damaged parts. ■ Remove the ...
-
Shindaiwa X7502825900 - page 22
22 T roubleshooting Guide V aporlock. V alve adjustment. Engine hot/heat soaked. Low fuel quality . V alve clearance too tight. V alve clearance too loose. Let cool completely and restar t. Refi ll with fresh, clean unleaded gasoline with a pump octane of 89 or higher mixed with an air cooled engine oil that meets or exceeds ISO-L-EGD and/or JASO ...
-
Shindaiwa X7502825900 - page 23
23 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose ter minal. Ignition failure. Piston seizure. Ground (stop) wire is disconnected, or switch i ...
-
Shindaiwa X7502825900 - page 24
24 ADDITIONAL PROBLEMS Poor acceleration. Clogged air fi lter . Clogged fuel fi lter . Lean fuel/air mixture. Idle speed set too low . Ignition switch tur ned of f. Fuel tank empty . W ater in the fuel. Clogged fuel fi lter . Shor ted spark plug or loose ter minal. Ignition failure. Piston seizure. Ground (stop) wire is disconnected, or switch i ...
-
Shindaiwa X7502825900 - page 25
25 SHINDAIW A LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO, INC’S RESPONSIBILITY ECHO Incorporated’s (ECHO, INC.) Limited W arranty , provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship. Under normal use and maintenance from date of purchas ...
-
Shindaiwa X7502825900 - page 26
26 PURCHASED REP AIR P ARTS AND ACCESSORIES • 90-day all applications A TTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance. T o help ensure the performance of the unit, it is required to use engine oil which meets ...
-
Shindaiwa X7502825900 - page 27
27 ECHO INCORPORA TED EMISSION CONTROL W ARRANTY ST A TEMENT FOR ECHO AND SHINDAIWA BRANDS The Environmental Protection Agency (EP A) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equip ...
-
Shindaiwa X7502825900 - page 28
28 NO TES ...
-
Shindaiwa X7502825900 - page 29
29 NO TES ...
-
Shindaiwa X7502825900 - page 30
30 NO TES ...
-
Shindaiwa X7502825900 - page 31
31 NO TES ...
-
Shindaiwa X7502825900 - page 32
Y amabiko Corporation 7-2 Suehirocho 1-Chome, Ohme, T okyo, 198-8760, Japan Phone: 81-428-32-61 18 Fax: 81-428-32-6145 Copyright© 2010 By Echo, Incorporated All Rights Reserved. ECHO Incorporated. 400 Oakwood Road Lake Zurich, IL 60047-1564 U.S.A. T elephone: 1-877-986-7783 Fax: 1-847-540-8416 www .shindaiwa.com Ser vicing Infor mation Par ts/Seri ...
У вас вопрос, касающийся Shindaiwa X7502825900?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Shindaiwa X7502825900, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Shindaiwa X7502825900 со всей вероятностью он захочет поделиться методом ее решения.