-
Harbor Freight Tools 95346 - page 1
GASOLINE A UGER DRILL 1.5 HP Model 95346 ASSEMBL Y AND OPERA TION INSTR UCTIONS Due to continuing impro vements, actual product ma y diff er slightly from the product descr ibed herein. CAUTION! Y our W arranty Is V oided If: Y ou do not operate the Auger Drill with the proper 25:1 unleaded fuel/2-cycle oil mix in its fuel tank. Never run the Engin ...
-
Harbor Freight Tools 95346 - page 2
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 2 REV 07b, 07e SPECIFICA TIONS Engine Specifications 1.5 HP / 52cc / Single Cylinder / 2-Stroke / Recoil Start Fuel Required 25:1 Unleaded Gasoline (89 octane or better) & 2 Cycle Oil Mixture Fuel T ank Capacity 0.26 Gallon Recommended Gear Oil SAE 80 – 90 Weight Gear Oil Ro ...
-
Harbor Freight Tools 95346 - page 3
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 3 GENERAL SAFETY RULES AND PRECAUTIONS W ARNING! READ AND UNDERST AND ALL INSTRUCTIONS Failure to f ollow all instructions listed belo w may result in electric shock, fire , and/or serious injury . SA VE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit. Cluttere ...
-
Harbor Freight Tools 95346 - page 4
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 4 Do not use the Auger Drill if the Kill Switch does not turn it off. Any tool that cannot be controlled with its Kill Switch is dangerous and must be replaced. Store idle tools out of reach of children and other untrained persons. T ools are dangerous in the hands of untrained use ...
-
Harbor Freight Tools 95346 - page 5
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 5 Never leave the Auger Drill unattended when it is running. T urn of f the Engine before leaving. Do not allow children and other unauthorized people to handle or play with the Auger Drill. Never leave the drill unattended in an area accessible to children. Always maintain a rm ...
-
Harbor Freight Tools 95346 - page 6
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 6 When spills of fuel or oil occur , they must be cleaned up immediately . Dis- pose of uids and cleaning materials as per any local, state, or federal codes and regulations. Store oil rags in a covered metal container . Never store fuel or other ammable materials near the Au ...
-
Harbor Freight Tools 95346 - page 7
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 7 UNP ACKING When unpacking, check to make sure all the parts shown on the Parts Lists on pages 14, 16, and 18 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible. ASSEMBL Y FIGURE A ...
-
Harbor Freight Tools 95346 - page 8
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 8 PRE-ST ART INSTRUCTIONS Fill the Fuel T ank IMPORT ANT! Y our warranty is voided if you do not operate the Auger Drill with the proper 25:1 fuel mix in its Fuel T ank (89). Never run the Engine with an improper fuel mix, low or no fuel mix. Running the Engine with an improper fue ...
-
Harbor Freight Tools 95346 - page 9
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 9 OPERA TION Starting and Stopping W ARNING! Always wear safety equipment. When operating the Auger Drill, always wear ANSI-approved safety impact eye goggles, hearing protection, heavy duty work gloves, sturdy work boots, and head protection. Place the Auger Drill on its side with ...
-
Harbor Freight Tools 95346 - page 10
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 10 W ARNING! The Auger (33a) should never turn at idle. If it is turning at idle, turn the Idle Screw of the Carburetor (shown right) co unterclock- wise to reduce the idle RPM and stop the Auger , or imme- diately discontinue using the Auger Drill and contact a quali- e d se rv ...
-
Harbor Freight Tools 95346 - page 11
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 1 1 Drilling a Hole Stand with a solid stance on stable gro und. Brac e you rsel f and main tain a proper grip with both hands on the Frame (1b) whenever the Engine is running. (See Figure E.) Accelerate the Engine to full throttle just before startin g to drill by sque ez- ing the ...
-
Harbor Freight Tools 95346 - page 12
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 12 INSPECTION, MAINTENANCE, AND CLEANING W ARNING! Always make sure the Spark Plug (51) is removed and the engine has cooled completely prior to performing any service, maintenance, or cleaning of the Auger Drill. Before each use: Inspect the general condition of the Auger Drill. C ...
-
Harbor Freight Tools 95346 - page 13
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 13 TROUBLESHOOTING Problem Possible Cause Possible Solution Engine will not start. Low or no fuel in fuel tank or improper fuel/2-cycle oil mix. Not enough fuel getting to carburetor . Faulty spark plug. Contaminated fuel. Insufcient electrical current getting to spark plug. 1. ...
-
Harbor Freight Tools 95346 - page 14
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 14 P ARTS LIST - ENGINE Part Description Qty . 1 Set Screw (M5 x 12) 1 2 Gasket 1 3 Reel 1 4 Starter Rope 1 5 Spiral Spring 1 6 Rewind Starter Assy . 1 7 Starter Handle 1 8 Handle Clip 1 9 Screw (M5 x 20) 6 10 Crankcase Gasket 1 1 1 Nut (M8) 1 12 Startup Claw 1 13 Startup Reed 1 14 ...
-
Harbor Freight Tools 95346 - page 15
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 15 ASSEMBL Y DIAGRAM - ENGINE ...
-
Harbor Freight Tools 95346 - page 16
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 16 P ARTS LIST - GEARBOX UNIT REV 07b Part Description Qty . 1a Starting Flange 1 2a Oil Seal (20 x 52 x 7) 1 3a W asher 1 4a W asher 1 5a Fender Ring (47) 1 6a Bearing (6204) 1 7a W orm Gear 1 8a Gearbox 1 9a Hex Head Screw (M6 x 25) 4 10a Stud (M6) 4 1 1a Nut (M6) 4 12a W asher 1 ...
-
Harbor Freight Tools 95346 - page 17
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 17 P ARTS LIST & ASSEMBL Y DIAGRAM - FRAME Part Description Qty . 1b Frame (Complete) 1 2b Handle 1 3b T ie Strip 3 4b Handle 1 5b Kill Switch 1 Part Description Qty . 6b Kill Switch Bracket 1 7b Screw (M12 x 20) 2 8b Accelerator Cable 1 9b Bushing 1 10b Speed Control 1 ...
-
Harbor Freight Tools 95346 - page 18
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 18 Emission Control System W arranty United States Emission Control Defects W arranty Statement The United States Environmental Protection Agency (herein EP A), and Harbor Freight T ools ® (herein HFT) are pleased to explain the emission control system warranty on your 1995 and la ...
-
Harbor Freight Tools 95346 - page 19
SKU 95346 For technical questions, please call 1-800-444-3353 P AGE 19 5. Service and Maintenance Component parts which are not scheduled for replacement as required maintenance or are scheduled only for regular inspection to the effect of “repair or replace as necessary” are warranted for the warranty period. Any warranted part which is schedu ...
У вас вопрос, касающийся Harbor Freight Tools 95346?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Harbor Freight Tools 95346, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Harbor Freight Tools 95346 со всей вероятностью он захочет поделиться методом ее решения.