Bedienungsanleitung Vision Fitness ST250

16 Seiten 2.61 mb
Download

Zur Seite of 16

Summary
  • Vision Fitness ST250 - page 1

    Assembly Guide ST250 LEG PRESS ...

  • Vision Fitness ST250 - page 2

    2 T o avoid possible damage to this Leg Press, please follow these assembly steps in the correct order . Before proceeding, find yo ur new Leg Press’ serial number located on the back of the base tube (1b), and enter here: Refer to this number when calling for ser vice, and enter this serial number on your W arranty Card and in your own records. ...

  • Vision Fitness ST250 - page 3

    3 5 STEP 3 STEP 2 STEP 4 STEP 6 STEP 7 STEP 8 STEP 1 STEP ...

  • Vision Fitness ST250 - page 4

    4 19mm Wrench 6mm L-Shaped Wrench (2) TOOLS & P AR TS INCLUDED P AR TS BOX Color-coded Hardware Bags Owner’ s Guide Assembly Guide W arranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench ...

  • Vision Fitness ST250 - page 5

    5 ORANGE BAG BLUE BAG HARDW ARE INCLUDED M10 x 1.5P Nut Quantity: 12 10.5 x 18 x 2T Flat W asher Quantity: 16 M10 x 1.5P x 60L Carriage Bolt Quantity: 2 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 8 M10 x 1.5P x 100L Bolt Quantity: 4 M10 x 1.5P Nut Quantity: 3 M10 x 1.5P x 30L Bolt Quantity: 8 M10 x 1.5P x 105L Bolt Quantity: 1 Pull Pin Quantity: ...

  • Vision Fitness ST250 - page 6

    6 PINK BAG GREEN BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 2 M10 x 1.5P Nut Quantity: 2 M6 x 1P x 15L Bolt Quantity: 3 90mm Shaft Quantity: 1 10.5 x 30 x 2T Flat W asher Quantity: 2 165mm Shaft Quantity: 1 SW6.1 x 12.2 x 1.5T Spring W asher Quantity: 3 6.4 x 14 x 1T Flat W asher Quantity: 3 SW10.2 x 18.4 x 2.5T Spring W asher Qua ...

  • Vision Fitness ST250 - page 7

    7 BLACK BAG 15x33L Shoulder Bolt Quantity: 1 U Bracket Quantity: 1 M12 Slotted Bolt Quantity: 1 M10 x 1.5P Nut Quantity: 1 10.5 x 18 x 2T Flat W asher Quantity: 1 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 1 HARDW ARE INCLUDED ...

  • Vision Fitness ST250 - page 8

    8 1 STEP • If you aren’t adding any weight plates to the stack, skip this step and proceed to Step 2. • Y our unit is equipped to handle 21-ten pound plates (20 plates and the header plate). If you are adding plates to the stack after it has been in use, proceed as follows: Loosen the nuts, attached to the bolts (5g) with a 10mm wrench and a ...

  • Vision Fitness ST250 - page 9

    9 1b 1a 1d 1c 1e 1e 2 STEP • Attach the connecting brace (1a) to the empty holes on the left floor support of the base unit ( ST200 ). Connect with two carriage bolts (M10x1.5Px60L), two fl at (10. 5x18x2 T) & s p r i n g (SW10.2x18.4x2.5T) washers, and two nuts (M10x1.5P). Attach the opposite end of the connecting brace to the main floor sup ...

  • Vision Fitness ST250 - page 10

    10 3 STEP • Lay the seatback (2a) face down. Mate the seatback support (2b) to 2a. Make sure the holes of 2b are pointing up towards the top of the seatback. Securely fasten four bolts (M10x1.5Px30L) into the seatback using a 6mm L-shaped wrench. Thread the pull pin partially into the opening of 1b. Guide the seatback into the oval opening at the ...

  • Vision Fitness ST250 - page 11

    11 4 STEP • Insert the lever ar m (3a) into the triangular structure at the front of 1b. When the holes are lined up, insert the 90mm shaft along with a flat (17 x25x 1.5 T) washer through the lower end of 3a and fasten with a flat (10.5x30x2T) washer and a bolt (M10x1.5Px20L). Tig ht en fi rm ly usi ng two 6mm L-shaped wrenches. • Insert the f ...

  • Vision Fitness ST250 - page 12

    12 5 STEP • If you already have the base unit assembled with cable #2 and are adding the leg press to it, follow this instruction, other wise proceed to Step 6: Unscrew the nuts and bolt that attaches cable #2 to the rear termination tube (6b of base unit), using a 19mm wrench. Unscrew the nuts from the slotted bolt. P u l l the cable out through ...

  • Vision Fitness ST250 - page 13

    13 6 STEP • Attach the pulley structure (U) to the bottom rear floor support of the base unit with three bolts (M6x1Px15L), three f l a t (6.4x14x1T), and three spring (SW6.1x12.2x1.5T) washers. Tighten with a 4mm L-shaped wrench. • Slide pulley structure (Q) through the back side of the rear vertical suppor t (base unit) and fasten securely wi ...

  • Vision Fitness ST250 - page 14

    14 7 STEP • Begin routing cable #6 with the end opposite the steel ball end. Feed the cable over pulley R, under S, around T , and under U. Unscrew the nut from the slotted bolt (M12). With the threads of the bolt facing up, slide cable #6 through it and reattach the nut. Thread the bolt into the post of pulley V , just enough so the cable won’ ...

  • Vision Fitness ST250 - page 15

    15 8 STEP • Attach the decals according to the diagram below . DECALS PINCH POINT SAFETY DECAL PLACEMENT ...

  • Vision Fitness ST250 - page 16

    500 South CP Avenue • P .O. Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 www .visionfitness.com © 2005 Vision Fitness. All Rights Reserved. 10.05 AG18.38PRD REV2 starts vision with a it all ...

Produzent Vision Fitness Kategorie Home Gym

Dokumente, die wir vom Produzenten des Geräts Vision Fitness ST250 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Vision Fitness
- Bedienungsanleitungen ST250
- Produktkarten Vision Fitness
- Informationsbroschüren
- oder Energieetiketten Vision Fitness ST250
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Vision Fitness ST250.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Vision Fitness ST250, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Vision Fitness ST250. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Vision Fitness ST250 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Vision Fitness ST250, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Vision Fitness ST250 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Vision Fitness ST250 verständlich ist.

Eine gänzliche Bedienungsanleitung von Vision Fitness sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Vision Fitness ST250 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Vision Fitness ST250 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Vision Fitness ST250, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Vision Fitness ST250 - die uns die ersten Schritte während der Nutzung von Vision Fitness ST250 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Vision Fitness ST250 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Vision Fitness ST250 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Vision Fitness ST250?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Vision Fitness ST250 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Vision Fitness ST250 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)