Vision Fitness ST250の取扱説明書

16ページ 2.61 mb
ダウンロード

ページに移動 of 16

Summary
  • Vision Fitness ST250 - page 1

    Assembly Guide ST250 LEG PRESS ...

  • Vision Fitness ST250 - page 2

    2 T o avoid possible damage to this Leg Press, please follow these assembly steps in the correct order . Before proceeding, find yo ur new Leg Press’ serial number located on the back of the base tube (1b), and enter here: Refer to this number when calling for ser vice, and enter this serial number on your W arranty Card and in your own records. ...

  • Vision Fitness ST250 - page 3

    3 5 STEP 3 STEP 2 STEP 4 STEP 6 STEP 7 STEP 8 STEP 1 STEP ...

  • Vision Fitness ST250 - page 4

    4 19mm Wrench 6mm L-Shaped Wrench (2) TOOLS & P AR TS INCLUDED P AR TS BOX Color-coded Hardware Bags Owner’ s Guide Assembly Guide W arranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench ...

  • Vision Fitness ST250 - page 5

    5 ORANGE BAG BLUE BAG HARDW ARE INCLUDED M10 x 1.5P Nut Quantity: 12 10.5 x 18 x 2T Flat W asher Quantity: 16 M10 x 1.5P x 60L Carriage Bolt Quantity: 2 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 8 M10 x 1.5P x 100L Bolt Quantity: 4 M10 x 1.5P Nut Quantity: 3 M10 x 1.5P x 30L Bolt Quantity: 8 M10 x 1.5P x 105L Bolt Quantity: 1 Pull Pin Quantity: ...

  • Vision Fitness ST250 - page 6

    6 PINK BAG GREEN BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 2 M10 x 1.5P Nut Quantity: 2 M6 x 1P x 15L Bolt Quantity: 3 90mm Shaft Quantity: 1 10.5 x 30 x 2T Flat W asher Quantity: 2 165mm Shaft Quantity: 1 SW6.1 x 12.2 x 1.5T Spring W asher Quantity: 3 6.4 x 14 x 1T Flat W asher Quantity: 3 SW10.2 x 18.4 x 2.5T Spring W asher Qua ...

  • Vision Fitness ST250 - page 7

    7 BLACK BAG 15x33L Shoulder Bolt Quantity: 1 U Bracket Quantity: 1 M12 Slotted Bolt Quantity: 1 M10 x 1.5P Nut Quantity: 1 10.5 x 18 x 2T Flat W asher Quantity: 1 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 1 HARDW ARE INCLUDED ...

  • Vision Fitness ST250 - page 8

    8 1 STEP • If you aren’t adding any weight plates to the stack, skip this step and proceed to Step 2. • Y our unit is equipped to handle 21-ten pound plates (20 plates and the header plate). If you are adding plates to the stack after it has been in use, proceed as follows: Loosen the nuts, attached to the bolts (5g) with a 10mm wrench and a ...

  • Vision Fitness ST250 - page 9

    9 1b 1a 1d 1c 1e 1e 2 STEP • Attach the connecting brace (1a) to the empty holes on the left floor support of the base unit ( ST200 ). Connect with two carriage bolts (M10x1.5Px60L), two fl at (10. 5x18x2 T) & s p r i n g (SW10.2x18.4x2.5T) washers, and two nuts (M10x1.5P). Attach the opposite end of the connecting brace to the main floor sup ...

  • Vision Fitness ST250 - page 10

    10 3 STEP • Lay the seatback (2a) face down. Mate the seatback support (2b) to 2a. Make sure the holes of 2b are pointing up towards the top of the seatback. Securely fasten four bolts (M10x1.5Px30L) into the seatback using a 6mm L-shaped wrench. Thread the pull pin partially into the opening of 1b. Guide the seatback into the oval opening at the ...

  • Vision Fitness ST250 - page 11

    11 4 STEP • Insert the lever ar m (3a) into the triangular structure at the front of 1b. When the holes are lined up, insert the 90mm shaft along with a flat (17 x25x 1.5 T) washer through the lower end of 3a and fasten with a flat (10.5x30x2T) washer and a bolt (M10x1.5Px20L). Tig ht en fi rm ly usi ng two 6mm L-shaped wrenches. • Insert the f ...

  • Vision Fitness ST250 - page 12

    12 5 STEP • If you already have the base unit assembled with cable #2 and are adding the leg press to it, follow this instruction, other wise proceed to Step 6: Unscrew the nuts and bolt that attaches cable #2 to the rear termination tube (6b of base unit), using a 19mm wrench. Unscrew the nuts from the slotted bolt. P u l l the cable out through ...

  • Vision Fitness ST250 - page 13

    13 6 STEP • Attach the pulley structure (U) to the bottom rear floor support of the base unit with three bolts (M6x1Px15L), three f l a t (6.4x14x1T), and three spring (SW6.1x12.2x1.5T) washers. Tighten with a 4mm L-shaped wrench. • Slide pulley structure (Q) through the back side of the rear vertical suppor t (base unit) and fasten securely wi ...

  • Vision Fitness ST250 - page 14

    14 7 STEP • Begin routing cable #6 with the end opposite the steel ball end. Feed the cable over pulley R, under S, around T , and under U. Unscrew the nut from the slotted bolt (M12). With the threads of the bolt facing up, slide cable #6 through it and reattach the nut. Thread the bolt into the post of pulley V , just enough so the cable won’ ...

  • Vision Fitness ST250 - page 15

    15 8 STEP • Attach the decals according to the diagram below . DECALS PINCH POINT SAFETY DECAL PLACEMENT ...

  • Vision Fitness ST250 - page 16

    500 South CP Avenue • P .O. Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 www .visionfitness.com © 2005 Vision Fitness. All Rights Reserved. 10.05 AG18.38PRD REV2 starts vision with a it all ...

メーカー Vision Fitness カテゴリー Home Gym

Vision Fitness ST250のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ST250の取扱説明書
- Vision Fitnessの製品カード
- パンフレット
- またはVision Fitness ST250の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Vision Fitness ST250の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Vision Fitness ST250の取り付け説明書、サービスマニュアル、簡易説明書、またはVision Fitness ST250のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Vision Fitness ST250の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Vision Fitness ST250デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがVision Fitness ST250を使用するのを助ける技術的文書のことです。説明書は通常、全てのVision Fitness ST250ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Vision Fitnessの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Vision Fitness ST250の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははVision Fitness ST250の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Vision Fitness ST250に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Vision Fitness ST250デバイスの基本機能を使うにあたってのヒント。 Vision Fitness ST250のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Vision Fitness ST250に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるVision Fitness ST250のメーカー/サービスへの連絡先に関する情報。

Vision Fitness ST250についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもVision Fitness ST250の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがVision Fitness ST250で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)