-
Patton electronic 2173 - page 1
USER MANUAL MODEL 2173 CopperLINK™ High Speed Ethernet Extender SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2173-UM Rev . A Revised 4/8/10 An ISO-9001Cer tified Company This is a Class A device and is intended for use in a light industrial (commercial) environment only . It is not intended nor approved for use in a h ...
-
Patton electronic 2173 - page 2
2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Regulatory Information ................................................................. 4 EMC Directive:.............................................................................. 4 Low-Voltage Direcive (Safety): ......................... ...
-
Patton electronic 2173 - page 3
3 D Distance Chart, Based on 24 AWG (0.5 MM) .......................... 19 ...
-
Patton electronic 2173 - page 4
4 1.0 WARRANTY INFORMATION P atton Electronics warrants all Model 2173 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment. This warranty is limited to def ects in w orkmanship or materials, and does not cov er customer damage, ab use or u ...
-
Patton electronic 2173 - page 5
5 of P ar t 15 of FCC rules, which are designed to provide reasonab le pro- tection from such interf erence in a commercial installation. Howe ver , there is no guarantee that interf erence will not occur in a par ticular instal- lation. If the de vice does cause interf erence to radio or tele vision recep- tion, which can be determined by disconne ...
-
Patton electronic 2173 - page 6
6 1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. This device can only be repaired by qualified service person- nel. • Do not open the device when the power cord is con- nected. For systems without a power switch and without an external power adapter , line voltages are present within the device when ...
-
Patton electronic 2173 - page 7
7 In accordance with the requirements of council direc- tive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you sepa- rate this product from other waste and scrap and deliver to the WEEE collection system in your country for recy- cling. This device is NOT intended nor approved for connec- tion to the ...
-
Patton electronic 2173 - page 8
8 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or par ts and labor . If any questions or prob lems ar ise during installation or use of this product, contact P atton Electronics T echnical Suppor t at +1 (301) 975-1007 ...
-
Patton electronic 2173 - page 9
9 Figure 1. T ypical application The pair of 2173 models work together to create a transparent e xtension between two peered Ethernet LANs. Figure 1 shows a typical point-to- point application. 3.0 INSTALLATION T o install the 2173 Ethernet Extender , do the follo wing: 1. Connect the line interf ace between the units (ref er to section 3.1, “Con ...
-
Patton electronic 2173 - page 10
10 Figure 2. Model 2173 standalone rear panel 3.1 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Model 2173 suppor ts communication between two peer Ethernet LAN sites ov er a distance of up to 4,250 ft (1.3 km) over 24 A WG (0.5 mm) twisted-pair wire. Note Actual distance and link performance ma y vary depending on the environment and type/gauge o ...
-
Patton electronic 2173 - page 11
11 1. T o function properly , the two Model 2173s m ust be connected together using twisted-pair , unconditioned, dr y , metal wire, between 19 (0.9mm) and 26 A WG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable . 2. The Model 2173 is equipped with an RJ-45 interf ace jack that can be used on the CopperLIN ...
-
Patton electronic 2173 - page 12
12 Figure 4. Model 2173 10/100Base-T RJ-45 Connector Pinout. 3.3 CONNECTING POWER The Model 2173 does not hav e a power s witch, so it powers up as soon as it is plugged in. An e xternal AC or DC pow er supply is av ailable separately . This connec- tion is made via the barrel jack on the rear panel of the Model 2173. No configuration is necessary ...
-
Patton electronic 2173 - page 13
13 Figure 5. Removing protectiv e cov er Figure 6 on page 13 shows the orientation of the DIP switches in the On and Off positions. Figure 6. DIP switch orientation Power Link Ethernet C o p p e r L IN K ™ H i g h S p e e d E t h e r n e t E x t e n d e r 1234 ON Push toggle up for ON position Switch toggle Push toggle down for OFF position 1234 ...
-
Patton electronic 2173 - page 14
14 4.2 CONFIGURING DIP SWITCH S1 DIP s witch S1 is where you configure the CopperLINK line . The f ollowing tables describe the configuration f or the 2173. S1-2: Impulse Noise Protection • Fast Mode: Direct data transmission with latency less than 1ms • Interleave Mode: Provides data transmission protection f or up to 250 ms impulse noise wi ...
-
Patton electronic 2173 - page 15
15 5.2 FRONT PANEL LED STATUS MONITORS The Model 2173 f eatures six front panel LEDs that monitor power , the Ethernet signals, the CopperLINK connection, and the remote/local set- ting. Figure 7 shows the front panel location of each LED . T ab le 2 on page 15 describes the LED functions. Figure 7. Model 2173 front panel T able 2: F ront panel LED ...
-
Patton electronic 2173 - page 16
16 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • T w o shielded RJ-45, 10/100Base-T , IEEE 802.3 Ethernet • CopperLINK Connection: Shielded RJ-45 A.2 TRANSMISSION LINE T w o-wire unconditioned twisted pair. A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE • Line Rate: 100/70 Mbps, upstream/downstream. Additional three line rates are a vailab ...
-
Patton electronic 2173 - page 17
17 APPENDIX B MODEL 2173 SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 2173/E CopperLINK Multi Rate 100 Mbps Ethernet Extender ; No power supply 2173/E-2PK CopperLINK Multi Rate 100 Mbps Ethernet Extender Kit (2 units preset to local and remote) ...
-
Patton electronic 2173 - page 18
18 APPENDIX C MODEL 2173 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection ...
-
Patton electronic 2173 - page 19
19 APPENDIX D DISTANCE CHAR T, BASED ON 24 A WG (0.5 MM) Note The actual distance and link performance ma y vary depending on the environment and type/gauge of wire used. Note DS = downstream, US = upstream Line Rate Distance in feet (km) Throughput at Max Distance (bits per second) 4/1 4250 ft (1.3 km) 4,629,408 (DS) 1,175,328 (US) 100/70 500 ft ( ...
-
Patton electronic 2173 - page 20
20 Cop yright © 2010. P atton Electronics Company All Rights Reser ved. ...
Haben Sie eine Frage bezüglich Patton electronic 2173?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Patton electronic 2173 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Patton electronic 2173 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.