-
Patton electronic 2173 - page 1
USER MANUAL MODEL 2173 CopperLINK™ High Speed Ethernet Extender SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2173-UM Rev . A Revised 4/8/10 An ISO-9001Cer tified Company This is a Class A device and is intended for use in a light industrial (commercial) environment only . It is not intended nor approved for use in a h ...
-
Patton electronic 2173 - page 2
2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Regulatory Information ................................................................. 4 EMC Directive:.............................................................................. 4 Low-Voltage Direcive (Safety): ......................... ...
-
Patton electronic 2173 - page 3
3 D Distance Chart, Based on 24 AWG (0.5 MM) .......................... 19 ...
-
Patton electronic 2173 - page 4
4 1.0 WARRANTY INFORMATION P atton Electronics warrants all Model 2173 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment. This warranty is limited to def ects in w orkmanship or materials, and does not cov er customer damage, ab use or u ...
-
Patton electronic 2173 - page 5
5 of P ar t 15 of FCC rules, which are designed to provide reasonab le pro- tection from such interf erence in a commercial installation. Howe ver , there is no guarantee that interf erence will not occur in a par ticular instal- lation. If the de vice does cause interf erence to radio or tele vision recep- tion, which can be determined by disconne ...
-
Patton electronic 2173 - page 6
6 1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. This device can only be repaired by qualified service person- nel. • Do not open the device when the power cord is con- nected. For systems without a power switch and without an external power adapter , line voltages are present within the device when ...
-
Patton electronic 2173 - page 7
7 In accordance with the requirements of council direc- tive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you sepa- rate this product from other waste and scrap and deliver to the WEEE collection system in your country for recy- cling. This device is NOT intended nor approved for connec- tion to the ...
-
Patton electronic 2173 - page 8
8 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or par ts and labor . If any questions or prob lems ar ise during installation or use of this product, contact P atton Electronics T echnical Suppor t at +1 (301) 975-1007 ...
-
Patton electronic 2173 - page 9
9 Figure 1. T ypical application The pair of 2173 models work together to create a transparent e xtension between two peered Ethernet LANs. Figure 1 shows a typical point-to- point application. 3.0 INSTALLATION T o install the 2173 Ethernet Extender , do the follo wing: 1. Connect the line interf ace between the units (ref er to section 3.1, “Con ...
-
Patton electronic 2173 - page 10
10 Figure 2. Model 2173 standalone rear panel 3.1 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Model 2173 suppor ts communication between two peer Ethernet LAN sites ov er a distance of up to 4,250 ft (1.3 km) over 24 A WG (0.5 mm) twisted-pair wire. Note Actual distance and link performance ma y vary depending on the environment and type/gauge o ...
-
Patton electronic 2173 - page 11
11 1. T o function properly , the two Model 2173s m ust be connected together using twisted-pair , unconditioned, dr y , metal wire, between 19 (0.9mm) and 26 A WG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable . 2. The Model 2173 is equipped with an RJ-45 interf ace jack that can be used on the CopperLIN ...
-
Patton electronic 2173 - page 12
12 Figure 4. Model 2173 10/100Base-T RJ-45 Connector Pinout. 3.3 CONNECTING POWER The Model 2173 does not hav e a power s witch, so it powers up as soon as it is plugged in. An e xternal AC or DC pow er supply is av ailable separately . This connec- tion is made via the barrel jack on the rear panel of the Model 2173. No configuration is necessary ...
-
Patton electronic 2173 - page 13
13 Figure 5. Removing protectiv e cov er Figure 6 on page 13 shows the orientation of the DIP switches in the On and Off positions. Figure 6. DIP switch orientation Power Link Ethernet C o p p e r L IN K ™ H i g h S p e e d E t h e r n e t E x t e n d e r 1234 ON Push toggle up for ON position Switch toggle Push toggle down for OFF position 1234 ...
-
Patton electronic 2173 - page 14
14 4.2 CONFIGURING DIP SWITCH S1 DIP s witch S1 is where you configure the CopperLINK line . The f ollowing tables describe the configuration f or the 2173. S1-2: Impulse Noise Protection • Fast Mode: Direct data transmission with latency less than 1ms • Interleave Mode: Provides data transmission protection f or up to 250 ms impulse noise wi ...
-
Patton electronic 2173 - page 15
15 5.2 FRONT PANEL LED STATUS MONITORS The Model 2173 f eatures six front panel LEDs that monitor power , the Ethernet signals, the CopperLINK connection, and the remote/local set- ting. Figure 7 shows the front panel location of each LED . T ab le 2 on page 15 describes the LED functions. Figure 7. Model 2173 front panel T able 2: F ront panel LED ...
-
Patton electronic 2173 - page 16
16 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • T w o shielded RJ-45, 10/100Base-T , IEEE 802.3 Ethernet • CopperLINK Connection: Shielded RJ-45 A.2 TRANSMISSION LINE T w o-wire unconditioned twisted pair. A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE • Line Rate: 100/70 Mbps, upstream/downstream. Additional three line rates are a vailab ...
-
Patton electronic 2173 - page 17
17 APPENDIX B MODEL 2173 SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 2173/E CopperLINK Multi Rate 100 Mbps Ethernet Extender ; No power supply 2173/E-2PK CopperLINK Multi Rate 100 Mbps Ethernet Extender Kit (2 units preset to local and remote) ...
-
Patton electronic 2173 - page 18
18 APPENDIX C MODEL 2173 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection ...
-
Patton electronic 2173 - page 19
19 APPENDIX D DISTANCE CHAR T, BASED ON 24 A WG (0.5 MM) Note The actual distance and link performance ma y vary depending on the environment and type/gauge of wire used. Note DS = downstream, US = upstream Line Rate Distance in feet (km) Throughput at Max Distance (bits per second) 4/1 4250 ft (1.3 km) 4,629,408 (DS) 1,175,328 (US) 100/70 500 ft ( ...
-
Patton electronic 2173 - page 20
20 Cop yright © 2010. P atton Electronics Company All Rights Reser ved. ...
У вас вопрос, касающийся Patton electronic 2173?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Patton electronic 2173, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Patton electronic 2173 со всей вероятностью он захочет поделиться методом ее решения.