Deutsch dropdown-ico

Bedienungsanleitung Jacuzzi BZ00000

28 Seiten 1.37 mb
Download

Zur Seite of 28

Summary
  • Jacuzzi BZ00000 - page 1

    SUMMER RAIN ™ II 2 PERSON SHOWER SYSTEM TWO W ALL AND THREE W ALL INST ALLA TION AND OPERA TING INSTRUCTIONS Jacuzzi Whirlpool Bath © BZ00000 03/05 ...

  • Jacuzzi BZ00000 - page 2

    Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath © products. Our warranty does not cover improper insta ...

  • Jacuzzi BZ00000 - page 3

    CONTENTS Specifications _________________________________________________________________________ 2 Enclosure Specifications ________________________________________________________________ 3 Rough-in Reference ____________________________________________________________________ 3 Component Identification ___________________________________________ ...

  • Jacuzzi BZ00000 - page 4

    Important: Read complete instructions before beginning installation. Each unit arrives ready for installation, equipped with base, glass and associated hardware. Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Immediately upon receipt, inspect the base and other components befo ...

  • Jacuzzi BZ00000 - page 5

    ROUGH-IN REFERENCE Shown is 2 wall left hand base. Right hand opposite. The 3 wall base has tile flange on both sides and back. ENCLOSURE SPECIFICATIONS 48" 27-1 1/16" TOP VIEW 72" 38-15/16" 36" 1" TILE FLANGE BLOWER MOTOR FOR UNITS WITH AIR AIR LINE FOR UNITS WITH AIR 84" 72" 48" FRONT VIEW SIDE VIEW 2 ...

  • Jacuzzi BZ00000 - page 6

    COMPONENT IDENTIFICA TION FRONT VIEW SIDE VIEW (2 WALL ONLY ) GLASS SIDE P ANEL GLASS DOORS RAIL BRACKET AND COVER CAP (2 WALL ONLY) (2 WALL ONLY) SIDE SUPPORT RAIL CENTER SUPPORT RAIL AIR TOWER W A TER TOWER SEA T BASE DOOR POST DOOR POST W A TER TOWER W ALL POST (2 WALL ONLY) W ALL RAIL W ALL POST AND JAMB (SUPPORT, SIDE SUPPORT RAIL, AND WALL RA ...

  • Jacuzzi BZ00000 - page 7

    PRELIMINARY ROUGH-IN The floor structure beneath the unit must be able to support a total weight of the unit and bather(s). Refer to page 2, SPECIFICATIONS, for weight speci- fications. Refer to COMPONENT IDENTIFICATION on page 4 to help identify parts. STEP 1 Provide an opening in the subfloor no less than 5" x 5" square. This opening sh ...

  • Jacuzzi BZ00000 - page 8

    STEP 6 With a large screwdriver and the tool included with the drain, tighten the inside compression nut to seal the drain pipe connection. After drain is fully installed, test for proper drainage. If the shower base does not drain properly, rectify this condition before proceeding with the installation. Jacuzzi Whirlpool Bath © is not re- sponsib ...

  • Jacuzzi BZ00000 - page 9

    CLEAN UP AFTER BASE INST ALLA TION To avoid dulling and scratching the acrylic surface of the base, never use abrasive cleaners. A mild liquid detergent and warm water clean soiled surfaces. Remove spilled plaster with a wood or plastic edge. Metal tools scratch the surface. Spots left by plaster or grout can be removed if lightly rubbed with deter ...

  • Jacuzzi BZ00000 - page 10

    T OWERS AND DOORS INST ALLA TION THESE INSTRUCTIONS ARE FOR SUMMER RAIN II 2 WALL AND 3 WALL UNITS WITH AND WITHOUT AIR FEATURE OPTION. Refer to COMPONENT IDENTIFICATION on page 4 to help identify parts. STEP 1 On the 2 wall unit attach the wall jamb to the water tower adjacent to the side wall. Then insert the wall post into the wall jamb. Do not ...

  • Jacuzzi BZ00000 - page 11

    TOWERS AND DOORS INST ALLA TION STEP 4 Place the center support rail into slot on each tower. If rail does not readily fit into slots, it may be necessary to loosen the bolts holding towers to base (it may only be necessary to loosen one tower). DO NOT FORCE CENTER RAIL INTO SLOTS. With center support rail in position, install hold down brackets bu ...

  • Jacuzzi BZ00000 - page 12

    TOWERS AND DOORS INST ALLA TION 10 Jacuzzi Whirlpool Bath © BZ00000 03/05 GROUT STUD SHIM IF NECESSARY DO NOT FILL CEMENT BOARD TILE SILICONE SEALANT 1-1/8" MAXIMUM NO MINIMUM SHOWER BASE CAULKING TILE CEMENT BOARD TILE ADHESIVE STUD FLANGE SHIM IF NECESSARY TO FILL GAPS BETWEEN STUD AND FLANGE STUD 1/8" GAP BETWEEN BASE & TILE DO NO ...

  • Jacuzzi BZ00000 - page 13

    STEP 9 (2 WALL ONLY) Place the side support rail into the slot on the water tower. Place the short wall rail into the slot on the other water tower. Rotate flat end of short wall rail flush to wall. With rails in position install hold down brackets, but do not tighten screws. Check water towers for level. Check side support rail for level and mark ...

  • Jacuzzi BZ00000 - page 14

    STEP 10 Two shut-off valves are provided per water tower. To hook up supply lines, unscrew valves from braided line. Using thread sealant, screw each valve to stub out at bottom of tower. Then reconnect braided line using provided gasket. Do not twist or kink supply lines when connecting. Perform this step for both water towers. SHUT OFF V AL VES ( ...

  • Jacuzzi BZ00000 - page 15

    TOWERS AND DOORS INST ALLA TION STEP 12 Move the door assembly to the door post on water tower and slide the assembly into the door post. Locate the base of the door into the slot of serrated door positioner that positions the hinge barrel as shown. BOTTOM OF DOOR FRAME HINGE BARREL SHOWER BASE WATER TOWER DOOR POST GLASS DOOR STEP 13 Check that th ...

  • Jacuzzi BZ00000 - page 16

    TOWERS AND DOORS INST ALLA TION FINISH W ALL EDGE OF BASE GLASS SIDE PANEL MOUNTED PARALLEL TO EDGE OF BASE W ALL POST T APE (3) SCREWS (3) STEP 15 (2 WALL ONLY) Position the fixed glass wall post so that the glass side panel will be parallel with the outside edge of the base. The fixed glass wall post position may vary slightly due to the anchored ...

  • Jacuzzi BZ00000 - page 17

    TOWER AND DOOR INST ALLA TION STEP 18 (2 WALL ONLY) Align the glass with glass jamb and insert. W ALL POST GLASS GLAZING GASKET INSIDE OF ENCLOSURE APPLY SEALANT JAMB GLASS GLAZING GASKET INSIDE OF ENCLOSURE APPLY SEALANT STEP 19 (2 WALL ONLY) Install glazing gasket on fixed glass wall post and jambs on the outside. Note orientation of gasket. Soap ...

  • Jacuzzi BZ00000 - page 18

    STEP 23 Install handles as shown. Note orientation of handle. Hand tighten knob. Flat screw has a screw driver notch. Do not over tighten either knob or flat screw as cracked glass may result. GLASS DOOR W ASHERS LARGE W ASHER INTERIOR OF SHOWER DOOR HINGE TOWER COVER INSERT THIS SIDE FIRST TOWER COVER TOWER T OP PLA TE TOWERS AND DOOR INST ALLA TI ...

  • Jacuzzi BZ00000 - page 19

    TOWERS AND DOOR INST ALLA TION STEP 26 Seal all around all bases of towers with sealant. Also seal the inside of wall posts, jambs, door posts, tile joint to wall post, and bottom of glass side panel on the inside only. CLEAN UP AFTER T OWERS AND DOOR INST ALLA TION To avoid dulling and scratching the tower surfaces and support rails never use abra ...

  • Jacuzzi BZ00000 - page 20

    OPERA TION SHOWER T OWERS 18 Jacuzzi Whirlpool Bath © BZ00000 03/05 Shower Head There are three selectable positions: Jet, Normal Pul- sating, and Aerated flow. Body Sprays (2 Upper and 2 Lower) To adjust the flow and intensity, turn as shown. The spray can also be turned to change the direction of the spray. Diverter Control To turn ON water, tur ...

  • Jacuzzi BZ00000 - page 21

    OPERA TION CONTROLLER To turn ON press ON/OFF button or turn ON water at either shower tower. The unit will then automatically go into a preheat cycle to heat the air transmission pipes. There will be a 5 (five) minute pause while the system preheats. During this time both LEDs will be ON. When ready for drying, press the ON/OFF button. Heat and ai ...

  • Jacuzzi BZ00000 - page 22

    To remove any lime scale from the shower head and body sprays, rub with your finger the outer ring of nozzles on the shower head and all nozzles on the body spray. To clean the foot temperature tester, unscrew the nozzle and back flush the wire mesh filter. Do not use metal tools (such as scissors or screwdrivers, etc.) to clean the body sprays, sh ...

  • Jacuzzi BZ00000 - page 23

    T OWER FIXTURES REP AIR P ARTS 21 Jacuzzi Whirlpool Bath © BZ00000 03/05 TOWER ASSEMBLY WASHER (PART OF D709827) 4 6 9 (5X) 10 11 (4X) 13 14 15 16 17 18 19 3 (5X) 2 (5X) 1 (5X) 8 5 12 PART OF D709827 7 (PART OF U547000) 1. C546000 Lock Nut, 1/2" NPT WP (5X) 2. G559000 Ring Compression SS (5X) 3. G560000 Washer Rubber (5X) 4. U546000 (Part of ...

  • Jacuzzi BZ00000 - page 24

    TOWER PLUMBING REP AIR P ARTS 1 11 4 5 4 7 10 6 14 12 13 5 4 16 11 2 8 2 3 2 3 3 17 15 9 18 19 18 18 18 ITEM NO. QTY. PART NO. DESCRIPTION 1 1 Y221000 TOWER, 2 PERSON SHOWER 2 3 U401000 FTG, ELL, .50" FST x 10 mm BARB 3 4 Y724000 1/2" ELBOW, SLIP x THREAD, SCH 40 4 3 7164000 ELL, STREET, .50", 90 o 5 2 0455000 1/2" TEE 6 1 72690 ...

  • Jacuzzi BZ00000 - page 25

    23 Jacuzzi Whirlpool Bath © BZ00000 03/05 ...

  • Jacuzzi BZ00000 - page 26

    Printed in U.S.A . Jacuzzi Whirlpool Bath © BZ00000 03/05 Printed on Recycled Pape r Jacuzzi Whirlpool Bath National Headquarters P.O. Box 702168, Dallas, TX 75370-2168 Service Support: (800) 288-4002 PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath © has obta ...

  • Jacuzzi BZ00000 - page 27

    Jacuzzi Whirlpool Bath P .O. Box 702168 Dallas, TX 75370-2168 WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The C ...

  • Jacuzzi BZ00000 - page 28

    RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In ...

Produzent Jacuzzi Kategorie Outdoor Shower

Dokumente, die wir vom Produzenten des Geräts Jacuzzi BZ00000 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Jacuzzi
- Bedienungsanleitungen BZ00000
- Produktkarten Jacuzzi
- Informationsbroschüren
- oder Energieetiketten Jacuzzi BZ00000
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Jacuzzi BZ00000.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Jacuzzi BZ00000, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Jacuzzi BZ00000. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Jacuzzi BZ00000 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Jacuzzi BZ00000, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Jacuzzi BZ00000 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Jacuzzi BZ00000 verständlich ist.

Eine gänzliche Bedienungsanleitung von Jacuzzi sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Jacuzzi BZ00000 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Jacuzzi BZ00000 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Jacuzzi BZ00000, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Jacuzzi BZ00000 - die uns die ersten Schritte während der Nutzung von Jacuzzi BZ00000 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Jacuzzi BZ00000 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Jacuzzi BZ00000 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Jacuzzi BZ00000?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Jacuzzi BZ00000 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Jacuzzi BZ00000 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)