Jacuzzi BZ00000の取扱説明書

28ページ 1.37 mb
ダウンロード

ページに移動 of 28

Summary
  • Jacuzzi BZ00000 - page 1

    SUMMER RAIN ™ II 2 PERSON SHOWER SYSTEM TWO W ALL AND THREE W ALL INST ALLA TION AND OPERA TING INSTRUCTIONS Jacuzzi Whirlpool Bath © BZ00000 03/05 ...

  • Jacuzzi BZ00000 - page 2

    Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath © products. Our warranty does not cover improper insta ...

  • Jacuzzi BZ00000 - page 3

    CONTENTS Specifications _________________________________________________________________________ 2 Enclosure Specifications ________________________________________________________________ 3 Rough-in Reference ____________________________________________________________________ 3 Component Identification ___________________________________________ ...

  • Jacuzzi BZ00000 - page 4

    Important: Read complete instructions before beginning installation. Each unit arrives ready for installation, equipped with base, glass and associated hardware. Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Immediately upon receipt, inspect the base and other components befo ...

  • Jacuzzi BZ00000 - page 5

    ROUGH-IN REFERENCE Shown is 2 wall left hand base. Right hand opposite. The 3 wall base has tile flange on both sides and back. ENCLOSURE SPECIFICATIONS 48" 27-1 1/16" TOP VIEW 72" 38-15/16" 36" 1" TILE FLANGE BLOWER MOTOR FOR UNITS WITH AIR AIR LINE FOR UNITS WITH AIR 84" 72" 48" FRONT VIEW SIDE VIEW 2 ...

  • Jacuzzi BZ00000 - page 6

    COMPONENT IDENTIFICA TION FRONT VIEW SIDE VIEW (2 WALL ONLY ) GLASS SIDE P ANEL GLASS DOORS RAIL BRACKET AND COVER CAP (2 WALL ONLY) (2 WALL ONLY) SIDE SUPPORT RAIL CENTER SUPPORT RAIL AIR TOWER W A TER TOWER SEA T BASE DOOR POST DOOR POST W A TER TOWER W ALL POST (2 WALL ONLY) W ALL RAIL W ALL POST AND JAMB (SUPPORT, SIDE SUPPORT RAIL, AND WALL RA ...

  • Jacuzzi BZ00000 - page 7

    PRELIMINARY ROUGH-IN The floor structure beneath the unit must be able to support a total weight of the unit and bather(s). Refer to page 2, SPECIFICATIONS, for weight speci- fications. Refer to COMPONENT IDENTIFICATION on page 4 to help identify parts. STEP 1 Provide an opening in the subfloor no less than 5" x 5" square. This opening sh ...

  • Jacuzzi BZ00000 - page 8

    STEP 6 With a large screwdriver and the tool included with the drain, tighten the inside compression nut to seal the drain pipe connection. After drain is fully installed, test for proper drainage. If the shower base does not drain properly, rectify this condition before proceeding with the installation. Jacuzzi Whirlpool Bath © is not re- sponsib ...

  • Jacuzzi BZ00000 - page 9

    CLEAN UP AFTER BASE INST ALLA TION To avoid dulling and scratching the acrylic surface of the base, never use abrasive cleaners. A mild liquid detergent and warm water clean soiled surfaces. Remove spilled plaster with a wood or plastic edge. Metal tools scratch the surface. Spots left by plaster or grout can be removed if lightly rubbed with deter ...

  • Jacuzzi BZ00000 - page 10

    T OWERS AND DOORS INST ALLA TION THESE INSTRUCTIONS ARE FOR SUMMER RAIN II 2 WALL AND 3 WALL UNITS WITH AND WITHOUT AIR FEATURE OPTION. Refer to COMPONENT IDENTIFICATION on page 4 to help identify parts. STEP 1 On the 2 wall unit attach the wall jamb to the water tower adjacent to the side wall. Then insert the wall post into the wall jamb. Do not ...

  • Jacuzzi BZ00000 - page 11

    TOWERS AND DOORS INST ALLA TION STEP 4 Place the center support rail into slot on each tower. If rail does not readily fit into slots, it may be necessary to loosen the bolts holding towers to base (it may only be necessary to loosen one tower). DO NOT FORCE CENTER RAIL INTO SLOTS. With center support rail in position, install hold down brackets bu ...

  • Jacuzzi BZ00000 - page 12

    TOWERS AND DOORS INST ALLA TION 10 Jacuzzi Whirlpool Bath © BZ00000 03/05 GROUT STUD SHIM IF NECESSARY DO NOT FILL CEMENT BOARD TILE SILICONE SEALANT 1-1/8" MAXIMUM NO MINIMUM SHOWER BASE CAULKING TILE CEMENT BOARD TILE ADHESIVE STUD FLANGE SHIM IF NECESSARY TO FILL GAPS BETWEEN STUD AND FLANGE STUD 1/8" GAP BETWEEN BASE & TILE DO NO ...

  • Jacuzzi BZ00000 - page 13

    STEP 9 (2 WALL ONLY) Place the side support rail into the slot on the water tower. Place the short wall rail into the slot on the other water tower. Rotate flat end of short wall rail flush to wall. With rails in position install hold down brackets, but do not tighten screws. Check water towers for level. Check side support rail for level and mark ...

  • Jacuzzi BZ00000 - page 14

    STEP 10 Two shut-off valves are provided per water tower. To hook up supply lines, unscrew valves from braided line. Using thread sealant, screw each valve to stub out at bottom of tower. Then reconnect braided line using provided gasket. Do not twist or kink supply lines when connecting. Perform this step for both water towers. SHUT OFF V AL VES ( ...

  • Jacuzzi BZ00000 - page 15

    TOWERS AND DOORS INST ALLA TION STEP 12 Move the door assembly to the door post on water tower and slide the assembly into the door post. Locate the base of the door into the slot of serrated door positioner that positions the hinge barrel as shown. BOTTOM OF DOOR FRAME HINGE BARREL SHOWER BASE WATER TOWER DOOR POST GLASS DOOR STEP 13 Check that th ...

  • Jacuzzi BZ00000 - page 16

    TOWERS AND DOORS INST ALLA TION FINISH W ALL EDGE OF BASE GLASS SIDE PANEL MOUNTED PARALLEL TO EDGE OF BASE W ALL POST T APE (3) SCREWS (3) STEP 15 (2 WALL ONLY) Position the fixed glass wall post so that the glass side panel will be parallel with the outside edge of the base. The fixed glass wall post position may vary slightly due to the anchored ...

  • Jacuzzi BZ00000 - page 17

    TOWER AND DOOR INST ALLA TION STEP 18 (2 WALL ONLY) Align the glass with glass jamb and insert. W ALL POST GLASS GLAZING GASKET INSIDE OF ENCLOSURE APPLY SEALANT JAMB GLASS GLAZING GASKET INSIDE OF ENCLOSURE APPLY SEALANT STEP 19 (2 WALL ONLY) Install glazing gasket on fixed glass wall post and jambs on the outside. Note orientation of gasket. Soap ...

  • Jacuzzi BZ00000 - page 18

    STEP 23 Install handles as shown. Note orientation of handle. Hand tighten knob. Flat screw has a screw driver notch. Do not over tighten either knob or flat screw as cracked glass may result. GLASS DOOR W ASHERS LARGE W ASHER INTERIOR OF SHOWER DOOR HINGE TOWER COVER INSERT THIS SIDE FIRST TOWER COVER TOWER T OP PLA TE TOWERS AND DOOR INST ALLA TI ...

  • Jacuzzi BZ00000 - page 19

    TOWERS AND DOOR INST ALLA TION STEP 26 Seal all around all bases of towers with sealant. Also seal the inside of wall posts, jambs, door posts, tile joint to wall post, and bottom of glass side panel on the inside only. CLEAN UP AFTER T OWERS AND DOOR INST ALLA TION To avoid dulling and scratching the tower surfaces and support rails never use abra ...

  • Jacuzzi BZ00000 - page 20

    OPERA TION SHOWER T OWERS 18 Jacuzzi Whirlpool Bath © BZ00000 03/05 Shower Head There are three selectable positions: Jet, Normal Pul- sating, and Aerated flow. Body Sprays (2 Upper and 2 Lower) To adjust the flow and intensity, turn as shown. The spray can also be turned to change the direction of the spray. Diverter Control To turn ON water, tur ...

  • Jacuzzi BZ00000 - page 21

    OPERA TION CONTROLLER To turn ON press ON/OFF button or turn ON water at either shower tower. The unit will then automatically go into a preheat cycle to heat the air transmission pipes. There will be a 5 (five) minute pause while the system preheats. During this time both LEDs will be ON. When ready for drying, press the ON/OFF button. Heat and ai ...

  • Jacuzzi BZ00000 - page 22

    To remove any lime scale from the shower head and body sprays, rub with your finger the outer ring of nozzles on the shower head and all nozzles on the body spray. To clean the foot temperature tester, unscrew the nozzle and back flush the wire mesh filter. Do not use metal tools (such as scissors or screwdrivers, etc.) to clean the body sprays, sh ...

  • Jacuzzi BZ00000 - page 23

    T OWER FIXTURES REP AIR P ARTS 21 Jacuzzi Whirlpool Bath © BZ00000 03/05 TOWER ASSEMBLY WASHER (PART OF D709827) 4 6 9 (5X) 10 11 (4X) 13 14 15 16 17 18 19 3 (5X) 2 (5X) 1 (5X) 8 5 12 PART OF D709827 7 (PART OF U547000) 1. C546000 Lock Nut, 1/2" NPT WP (5X) 2. G559000 Ring Compression SS (5X) 3. G560000 Washer Rubber (5X) 4. U546000 (Part of ...

  • Jacuzzi BZ00000 - page 24

    TOWER PLUMBING REP AIR P ARTS 1 11 4 5 4 7 10 6 14 12 13 5 4 16 11 2 8 2 3 2 3 3 17 15 9 18 19 18 18 18 ITEM NO. QTY. PART NO. DESCRIPTION 1 1 Y221000 TOWER, 2 PERSON SHOWER 2 3 U401000 FTG, ELL, .50" FST x 10 mm BARB 3 4 Y724000 1/2" ELBOW, SLIP x THREAD, SCH 40 4 3 7164000 ELL, STREET, .50", 90 o 5 2 0455000 1/2" TEE 6 1 72690 ...

  • Jacuzzi BZ00000 - page 25

    23 Jacuzzi Whirlpool Bath © BZ00000 03/05 ...

  • Jacuzzi BZ00000 - page 26

    Printed in U.S.A . Jacuzzi Whirlpool Bath © BZ00000 03/05 Printed on Recycled Pape r Jacuzzi Whirlpool Bath National Headquarters P.O. Box 702168, Dallas, TX 75370-2168 Service Support: (800) 288-4002 PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath © has obta ...

  • Jacuzzi BZ00000 - page 27

    Jacuzzi Whirlpool Bath P .O. Box 702168 Dallas, TX 75370-2168 WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The C ...

  • Jacuzzi BZ00000 - page 28

    RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In ...

メーカー Jacuzzi カテゴリー Outdoor Shower

Jacuzzi BZ00000のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- BZ00000の取扱説明書
- Jacuzziの製品カード
- パンフレット
- またはJacuzzi BZ00000の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Jacuzzi BZ00000の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Jacuzzi BZ00000の取り付け説明書、サービスマニュアル、簡易説明書、またはJacuzzi BZ00000のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Jacuzzi BZ00000の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Jacuzzi BZ00000デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJacuzzi BZ00000を使用するのを助ける技術的文書のことです。説明書は通常、全てのJacuzzi BZ00000ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Jacuzziの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Jacuzzi BZ00000の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJacuzzi BZ00000の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Jacuzzi BZ00000に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Jacuzzi BZ00000デバイスの基本機能を使うにあたってのヒント。 Jacuzzi BZ00000のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Jacuzzi BZ00000に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJacuzzi BZ00000のメーカー/サービスへの連絡先に関する情報。

Jacuzzi BZ00000についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJacuzzi BZ00000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJacuzzi BZ00000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)