Bedienungsanleitung Western Telematic CAS-161A

19 Seiten 0.19 mb
Download

Zur Seite of 19

Summary
  • Western Telematic CAS-161A - page 1

    CAS-161A Code Activa ted Switch User’s Guide 5 Sterling Irvine California 92618 (949) 586-9950 Toll Free: 1-800-854-7226 Fax: (949) 583-9514 http://www.wti.com ...

  • Western Telematic CAS-161A - page 2

    Table of Contents 1. Introduction ............................................. 1-1 2. Unit Description .......................................... 2-1 2.1. Front Panel Indicators .................................... 2-1 2.2. Back Panel Components ................................... 2-2 3. Installation ............................................. 3 ...

  • Western Telematic CAS-161A - page 3

    1. Introduction The CAS-161A Code Activated Switch enables a single RS232 Control port to switch between 16 to 64 ports via an ASCII code sequence. The code sequence is a user-selectable Prefix code and a Port Select code. The Prefix code is set via the Setup switch on the bottom of the unit. For added security , the Setup switch can be set to requ ...

  • Western Telematic CAS-161A - page 4

    2. Unit Description 2.1. Front Panel Indicators À PWR: (Power) Indicates power to the unit is ON. Á TXD: (T ransmit Data) Indicates data is being transmitted out pin 2 of the Control port (MODEM Port). Indicates data is being received at pin 2 of the selected port. Â RXD: (Receive Data) Indicates data is being received at pin 3 of the Control po ...

  • Western Telematic CAS-161A - page 5

    2.2. Back Panel Components À Input Port s1-1 6 : Ports labele d1-1 6a r e 25-pin, female, RS232 connectors. Optional RS422 connectors can be factory installed to increase data transmission distance. For a description of the port interface, please refer to Appendix A. Á MODEM Port (Control Port): A 25-pin, female, RS232 connector . For a descripti ...

  • Western Telematic CAS-161A - page 6

    3. Installation 3.1. Configure SetUp Switches There are two banks of DIP switches located on the bottom of the CAS-161A unit. These switches are used to configure the Prefix Code (command character), enable the Broadcast Mode, and select the baud rate. Switch functions are summarized on the bottom of the unit and in the sections that follow: Note: ...

  • Western Telematic CAS-161A - page 7

    3.1.1.3. Baud Rate Select (Sw6 - Sw8) Selects the operating baud rate; from 150 to 19.2K baud. Baud Rate Switch (Bank 1) 678 * = Factory Setting 3-2 ...

  • Western Telematic CAS-161A - page 8

    3.1.2. SetUp Switch Bank 2 The bank of DIP switches located closest to the front panel are used to select the Prefix Code character and set the parity . 3.1.2.1. Prefix Code (Sw1 - Sw7) As mentioned previously , the Prefix Code informs the unit that the next character will be a command. The Prefix code can be any ASCII character . However , since i ...

  • Western Telematic CAS-161A - page 9

    3.1.2.2. Parity (Sw8) Parity can be set to Even, Mark, Odd, None, or Space. Parity Switch 8 (Bank 2) 1 (On) 0 (Off) 3.2. Connect Power Cable 1. Make certain the power switch is in the OFF position. 2. Attach one end of the power cable to the AC power connector on the CAS-161A. Attach the other end to a grounded wall outlet. 3.3. Connect Data Cables ...

  • Western Telematic CAS-161A - page 10

    4. Port Selection 4.1. Selecting a Port 1. After completing the installation procedure, flip the power switch on the back of the unit to ON. Note: Upon each power-up the unit will reset and all ports will be closed. 2. Refer to the Port Select Code Chart below and find the letter representing the port you wish to connect to. Module 1 Module 2 Modul ...

  • Western Telematic CAS-161A - page 11

    Examples: Assume the Prefix Code is ^V and the Prefix Code Repetition V alue is 4. T o connect to Port 14, use the following command: ^V^V^V^VM Assume the Prefix Code is ^Y and the Prefix Code Repetition V alue is 1. T o connect to Port 44, use the following command: ^Yk 4.2. Closing/Opening All Ports 1. T o close all ports at once, enter the Prefi ...

  • Western Telematic CAS-161A - page 12

    A. Interface Description A.1. RS232 Ports (Standard) A.2. RS422 Ports (Optional) Note: Handshake signals are not passed. Pin s1-1 3a r e open. Apx-1 ...

  • Western Telematic CAS-161A - page 13

    B. Printable Prefix Codes Since the Prefix code is transmitted through the opened port, it is best to select a non-printable Prefix Code. The procedure for selecting the Prefix Code is described in Section 3. If your application requires a printable code, refer to the ASCII code chart below . Remember: · Switch position s1-7 correspond to ASC bits ...

  • Western Telematic CAS-161A - page 14

    C. Installing Add-On Modules The CAS-161A is field expandable to 32, 48, or 64 ports by attaching up to three additional Add-On Modules to the master unit. Each Add-On Module Kit includes the following: · 1 ea. Add-On Module w/ six-wire power cable · 2 ea. Connecting Plates · 1 ea. Left Rack-Mount Bracket (Style-2) · 1 ea. Right Rack-Mount Brac ...

  • Western Telematic CAS-161A - page 15

    1. Remove the instrument top cover . If your unit has a stand-alone top cover , remove the cover; the stand-alone cover is no longer required. If your unit has a Rack-Mount Kit, remove the Rack-Mount Cover , Left and Right Rack-Mount Brackets (Style 1), and screws. Save these parts, they will be used later . 2. Locate and unroll the ribbon cable (A ...

  • Western Telematic CAS-161A - page 16

    D. Specifications Coding: ASCII, Asynchronous Baud Rate: 300 to 19.2K baud, Switch Selectable Interface: RS232, 25-pin connectors Lines Switched: 2,3,4 and 5. Pins 6 and 8 of all Input ports follow Pin 6 of the Control port. Power: 90 V AC to 130 V AC (jumper-selectable), 180 V AC to 260 V AC, 47 to 450 Hz. Ambient T emp: 25 ° Operating T emp: 0 ? ...

  • Western Telematic CAS-161A - page 17

    E. Customer Service Customer Service hours are from 8:00 AM to 5:00 PM, PST , Monday through Friday . When calling, please be prepared to give the name and make of the unit, its serial number and a description of its symptoms. If the unit should need to be returned for factory repair it must be accompanied by a Return Authorization number from Cust ...

  • Western Telematic CAS-161A - page 18

    F. FCC Statement W ARNING: This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio and television reception. It has been tested and found to comply with the limits for a Class A computing device in accordance with specifications in ...

  • Western Telematic CAS-161A - page 19

    Trademark and Copyright Information WTI, WTI logo and W estern T elematic are trademarks of W estern T elematic Inc. All other product names mentioned in this publication are trademarks or registered trademarks of their respective companies. Information and descriptions contained herein are the property of W estern T elematic Inc. Such information ...

Produzent Western Telematic Kategorie Switch

Dokumente, die wir vom Produzenten des Geräts Western Telematic CAS-161A erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Western Telematic
- Bedienungsanleitungen CAS-161A
- Produktkarten Western Telematic
- Informationsbroschüren
- oder Energieetiketten Western Telematic CAS-161A
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Western Telematic CAS-161A.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Western Telematic CAS-161A, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Western Telematic CAS-161A. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Western Telematic CAS-161A ansehen.

Die komplette Bedienungsanleitung des Geräts Western Telematic CAS-161A, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Western Telematic CAS-161A hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Western Telematic CAS-161A verständlich ist.

Eine gänzliche Bedienungsanleitung von Western Telematic sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Western Telematic CAS-161A bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Western Telematic CAS-161A befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Western Telematic CAS-161A, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Western Telematic CAS-161A - die uns die ersten Schritte während der Nutzung von Western Telematic CAS-161A erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Western Telematic CAS-161A hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Western Telematic CAS-161A im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Western Telematic CAS-161A?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Western Telematic CAS-161A nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Western Telematic CAS-161A hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)