Bedienungsanleitung New Buck Corporation 80ZC

18 Seiten 0.51 mb
Download

Zur Seite of 18

Summary
  • New Buck Corporation 80ZC - page 1

    The following manual is for the 80ZC cabinet ONLY. If you require information on the Model 80 unit that fits inside this cabinet, please download the Model 80 manual from the “Stove Manuals” section of our website. Thank you for choosing Buck Stove! ...

  • New Buck Corporation 80ZC - page 2

    MODEL 80 ZC CABINET INSTALLATION FEATURES: INSTALLATION: MAINTENANCE: PREPARATION: OPERATION: SAFETY: NEW BUCK CORPORATION 1992 NARNOCK HERSEY ...

  • New Buck Corporation 80ZC - page 3

    IMPORTANT I The Top Panel (#1 ) And Side-Panels (#2) Must Be Installed _On Cabinet Before Setting The Cabinet For Framing. tf. FRONT o S IDE PANEL ~ INSLlAT ION LAYERS ~ I I 0 TOP PANEL - ~ INSllATION CAP ~ " I h, _ ~it1- ~ TeP PANEL ~ ~ I KfiA'l" IKIM I f- r -P FRONT I LOUVl:RS I FRONT 0 ~ ~'xx 0 >tx > I- , --1 =' ...

  • New Buck Corporation 80ZC - page 4

    CAUTION - Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. Be sure to follow chimney instructions for proper clearances to combusti- bles and proper air spacing required. -',- Chlmnoy Cap -1- ~pp<OvO<l ch ..... y pipo A CAUTION: Vented Root Flashings are required with certain chimney installa· t ...

  • New Buck Corporation 80ZC - page 5

    CAUTION: Do not mix Ch imney P arts as a fire. may re su 1 t. Use one model of listed chimney parts completely for·an instal~ation. CAUTION: Read through all of these instructions carefully. Follow Chimney Manufacturer's Installation exactly. Failure to install the Cabinet, Stove, and Chimney as described in the instructions will void the man ...

  • New Buck Corporation 80ZC - page 6

    INSTALLATION PRECAUTIONS The following precautions are mandatory for a safe installation: A. Compliance with local building codes and regulations is mandatory. B. Be careful not to damage unit in handling and unpacking component parts and accessories. C. Use only listed approved chimney pipes. D. The chimney must extend a minimum of three feet abov ...

  • New Buck Corporation 80ZC - page 7

    A. Straight up through ceiling: (See Figures 1 and 2). This is a simple installation normally used when installing a Hodel ZC-80 inside an existing room, and in iome cases, in new construction. Refer to Figure 3 if an offset to clear an obstruction is needed. CAUTION- Refer to chimney manufacturers instructions for assembly and disassembly of chimn ...

  • New Buck Corporation 80ZC - page 8

    FRAMING CONSTRUCTION Except as noted, the Hodel ZC-80 can be installed almost anywhere you desire. There are, however, a few clearance and framing restrictions that must be followed. See figures 1 and 2 to make sure that these clearance restrictions are met. It is much wiser to place your Hodel ZC-80 correctly at the start of the installa- tion tha ...

  • New Buck Corporation 80ZC - page 9

    Framing must be accomplished after the Model ZC-80 is set in place. The chimney can be installed after framing, but installa- tion is considerably more difficult and, in some cases, impossi- ble. Therefore, it is recommended that the chimney be installed prior to framing when a choice exists. '~ ~t: LJ ± lZ rr~'Bl.lllzm<f1~mm_" A ...

  • New Buck Corporation 80ZC - page 10

    2. Set Hodel ZC-80 unit in place and attach safety shield to unit as shown in Figure i-A and i-B. You must place a noncom- bustible material 3/4" thick millboard or equivalent K Factor =.084/BTU/F 2 H0F inches minimum. 3. Frame the ZC Cabinet usng 2"x 4" studs or local building code framing. Some minor framing restrictions are requir ...

  • New Buck Corporation 80ZC - page 11

    NOTE: Finished wall must be 2" in front of face of Z.C. Cabinet (without hood panell. Singi. H •• der A Single Header must be used as part of front Iraming, vertical 2" .... ·s must be turned flat. WARNING! Install the hearth protector only as specified. The hearth extension must extend a minimum of 16" in front of the fireplace ...

  • New Buck Corporation 80ZC - page 12

    CAUTION! Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. Be sure to follow chimney instructions for proper clearances to combusti- bles and proper air spacing required. ffi--- Chimney Cap 0--.--1- Storm Collar ---:f-- Roof Flashing -+ Chimney Pipe ,.....e;~~"'-7"'5..-s-'lt-ttt1-- ...

  • New Buck Corporation 80ZC - page 13

    Install pipe to cabinet by pushing down over the ~tarter section of pipe on the ZC Cabinet. NOTE: To ease installation of the first section of pipe to the Cabinet use a pipe crimping tool and crimp the bottom of the inside chimney liner. Install pipe to cabinet by pushing down over the starter section of pipe on the ZC Cabinet. Maintain a 2 inch mi ...

  • New Buck Corporation 80ZC - page 14

    INSTALLING FIRESTOP RADIATION SHIELD: Nail the firestop Radia- tion Shield to' the bottom of the framed ceiling opening using at least two 8-penny nails per side. CHIMNEY INSTALLATION INFORMATION ROOF CLEARANCE Frame a square opening in roof maintaining the required 2" /' clearance to combustible materials between the chimney and the ...

  • New Buck Corporation 80ZC - page 15

    Electrical procedures: The ZC-80 Cabinet is not pre-wired; an electrician must wire the Cabinet into the home wiring. system using No. 14 AWG (with ground wiring) as minimum in accordance with local wiring codes. (See Figure 9) 1. Remove receptacle cover. 2. Remove receptacle from mounting box. 3. Run No. 14 AWG wire directly from house wiring in t ...

  • New Buck Corporation 80ZC - page 16

    FINISHING Finishing can now be completed using the desired material in accordance with local building and fire codes. CAUTION: Do not cover any opening on the Cabinet; heat must be allowed to escape from the openings designed into the unit. A grilled trim panel is provided with the trim package to cover this area. Also, the grilled opening at the b ...

  • New Buck Corporation 80ZC - page 17

    INSTALLING THE MODEL 80 BUCK STOVE Install unit as follows: A. Carefully reinspect chimney connections, vent outputs and cabinet air intakes after finishing is completed. B. Thoroughly clean all masonry mud and debris from cabinet and surrounding environment. C. Ensure that Cabinet has not been damaged during masonry pro- cess. D. Remove protective ...

  • New Buck Corporation 80ZC - page 18

    H. Install the trim kit attaching it to the Cabinet or finished framing by using 1" screws to secure the trim panels in place. I. Remove cover plate from Cabinet exposing receptacle. Roll up pOHer cord so it will fit inside of cover box. Plug in pOHer cord in receptacle. Re- place cover plate. (See Figure 10). ~ . .... Cover Plate / / o / &quo ...

Produzent New Buck Corporation Kategorie Cooktop

Dokumente, die wir vom Produzenten des Geräts New Buck Corporation 80ZC erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen New Buck Corporation
- Bedienungsanleitungen 80ZC
- Produktkarten New Buck Corporation
- Informationsbroschüren
- oder Energieetiketten New Buck Corporation 80ZC
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung New Buck Corporation 80ZC.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen New Buck Corporation 80ZC, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen New Buck Corporation 80ZC. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts New Buck Corporation 80ZC ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts New Buck Corporation 80ZC, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von New Buck Corporation 80ZC hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von New Buck Corporation 80ZC verständlich ist.

Eine gänzliche Bedienungsanleitung von New Buck Corporation sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von New Buck Corporation 80ZC bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von New Buck Corporation 80ZC befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich New Buck Corporation 80ZC, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts New Buck Corporation 80ZC - die uns die ersten Schritte während der Nutzung von New Buck Corporation 80ZC erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit New Buck Corporation 80ZC hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von New Buck Corporation 80ZC im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich New Buck Corporation 80ZC?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit New Buck Corporation 80ZC nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit New Buck Corporation 80ZC hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)