English dropdown-ico

Manual New Buck Corporation 80ZC

18 pages 0.51 mb
Download

Go to site of 18

Summary
  • New Buck Corporation 80ZC - page 1

    The following manual is for the 80ZC cabinet ONLY. If you require information on the Model 80 unit that fits inside this cabinet, please download the Model 80 manual from the “Stove Manuals” section of our website. Thank you for choosing Buck Stove! ...

  • New Buck Corporation 80ZC - page 2

    MODEL 80 ZC CABINET INSTALLATION FEATURES: INSTALLATION: MAINTENANCE: PREPARATION: OPERATION: SAFETY: NEW BUCK CORPORATION 1992 NARNOCK HERSEY ...

  • New Buck Corporation 80ZC - page 3

    IMPORTANT I The Top Panel (#1 ) And Side-Panels (#2) Must Be Installed _On Cabinet Before Setting The Cabinet For Framing. tf. FRONT o S IDE PANEL ~ INSLlAT ION LAYERS ~ I I 0 TOP PANEL - ~ INSllATION CAP ~ " I h, _ ~it1- ~ TeP PANEL ~ ~ I KfiA'l" IKIM I f- r -P FRONT I LOUVl:RS I FRONT 0 ~ ~'xx 0 >tx > I- , --1 =' ...

  • New Buck Corporation 80ZC - page 4

    CAUTION - Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. Be sure to follow chimney instructions for proper clearances to combusti- bles and proper air spacing required. -',- Chlmnoy Cap -1- ~pp<OvO<l ch ..... y pipo A CAUTION: Vented Root Flashings are required with certain chimney installa· t ...

  • New Buck Corporation 80ZC - page 5

    CAUTION: Do not mix Ch imney P arts as a fire. may re su 1 t. Use one model of listed chimney parts completely for·an instal~ation. CAUTION: Read through all of these instructions carefully. Follow Chimney Manufacturer's Installation exactly. Failure to install the Cabinet, Stove, and Chimney as described in the instructions will void the man ...

  • New Buck Corporation 80ZC - page 6

    INSTALLATION PRECAUTIONS The following precautions are mandatory for a safe installation: A. Compliance with local building codes and regulations is mandatory. B. Be careful not to damage unit in handling and unpacking component parts and accessories. C. Use only listed approved chimney pipes. D. The chimney must extend a minimum of three feet abov ...

  • New Buck Corporation 80ZC - page 7

    A. Straight up through ceiling: (See Figures 1 and 2). This is a simple installation normally used when installing a Hodel ZC-80 inside an existing room, and in iome cases, in new construction. Refer to Figure 3 if an offset to clear an obstruction is needed. CAUTION- Refer to chimney manufacturers instructions for assembly and disassembly of chimn ...

  • New Buck Corporation 80ZC - page 8

    FRAMING CONSTRUCTION Except as noted, the Hodel ZC-80 can be installed almost anywhere you desire. There are, however, a few clearance and framing restrictions that must be followed. See figures 1 and 2 to make sure that these clearance restrictions are met. It is much wiser to place your Hodel ZC-80 correctly at the start of the installa- tion tha ...

  • New Buck Corporation 80ZC - page 9

    Framing must be accomplished after the Model ZC-80 is set in place. The chimney can be installed after framing, but installa- tion is considerably more difficult and, in some cases, impossi- ble. Therefore, it is recommended that the chimney be installed prior to framing when a choice exists. '~ ~t: LJ ± lZ rr~'Bl.lllzm<f1~mm_" A ...

  • New Buck Corporation 80ZC - page 10

    2. Set Hodel ZC-80 unit in place and attach safety shield to unit as shown in Figure i-A and i-B. You must place a noncom- bustible material 3/4" thick millboard or equivalent K Factor =.084/BTU/F 2 H0F inches minimum. 3. Frame the ZC Cabinet usng 2"x 4" studs or local building code framing. Some minor framing restrictions are requir ...

  • New Buck Corporation 80ZC - page 11

    NOTE: Finished wall must be 2" in front of face of Z.C. Cabinet (without hood panell. Singi. H •• der A Single Header must be used as part of front Iraming, vertical 2" .... ·s must be turned flat. WARNING! Install the hearth protector only as specified. The hearth extension must extend a minimum of 16" in front of the fireplace ...

  • New Buck Corporation 80ZC - page 12

    CAUTION! Refer to chimney manufacturers instructions for assembly and disassembly of chimney parts. Be sure to follow chimney instructions for proper clearances to combusti- bles and proper air spacing required. ffi--- Chimney Cap 0--.--1- Storm Collar ---:f-- Roof Flashing -+ Chimney Pipe ,.....e;~~"'-7"'5..-s-'lt-ttt1-- ...

  • New Buck Corporation 80ZC - page 13

    Install pipe to cabinet by pushing down over the ~tarter section of pipe on the ZC Cabinet. NOTE: To ease installation of the first section of pipe to the Cabinet use a pipe crimping tool and crimp the bottom of the inside chimney liner. Install pipe to cabinet by pushing down over the starter section of pipe on the ZC Cabinet. Maintain a 2 inch mi ...

  • New Buck Corporation 80ZC - page 14

    INSTALLING FIRESTOP RADIATION SHIELD: Nail the firestop Radia- tion Shield to' the bottom of the framed ceiling opening using at least two 8-penny nails per side. CHIMNEY INSTALLATION INFORMATION ROOF CLEARANCE Frame a square opening in roof maintaining the required 2" /' clearance to combustible materials between the chimney and the ...

  • New Buck Corporation 80ZC - page 15

    Electrical procedures: The ZC-80 Cabinet is not pre-wired; an electrician must wire the Cabinet into the home wiring. system using No. 14 AWG (with ground wiring) as minimum in accordance with local wiring codes. (See Figure 9) 1. Remove receptacle cover. 2. Remove receptacle from mounting box. 3. Run No. 14 AWG wire directly from house wiring in t ...

  • New Buck Corporation 80ZC - page 16

    FINISHING Finishing can now be completed using the desired material in accordance with local building and fire codes. CAUTION: Do not cover any opening on the Cabinet; heat must be allowed to escape from the openings designed into the unit. A grilled trim panel is provided with the trim package to cover this area. Also, the grilled opening at the b ...

  • New Buck Corporation 80ZC - page 17

    INSTALLING THE MODEL 80 BUCK STOVE Install unit as follows: A. Carefully reinspect chimney connections, vent outputs and cabinet air intakes after finishing is completed. B. Thoroughly clean all masonry mud and debris from cabinet and surrounding environment. C. Ensure that Cabinet has not been damaged during masonry pro- cess. D. Remove protective ...

  • New Buck Corporation 80ZC - page 18

    H. Install the trim kit attaching it to the Cabinet or finished framing by using 1" screws to secure the trim panels in place. I. Remove cover plate from Cabinet exposing receptacle. Roll up pOHer cord so it will fit inside of cover box. Plug in pOHer cord in receptacle. Re- place cover plate. (See Figure 10). ~ . .... Cover Plate / / o / &quo ...

Manufacturer New Buck Corporation Category Cooktop

Documents that we receive from a manufacturer of a New Buck Corporation 80ZC can be divided into several groups. They are, among others:
- New Buck Corporation technical drawings
- 80ZC manuals
- New Buck Corporation product data sheets
- information booklets
- or energy labels New Buck Corporation 80ZC
All of them are important, but the most important information from the point of view of use of the device are in the user manual New Buck Corporation 80ZC.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals New Buck Corporation 80ZC, service manual, brief instructions and user manuals New Buck Corporation 80ZC. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product New Buck Corporation 80ZC.

Similar manuals

A complete manual for the device New Buck Corporation 80ZC, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use New Buck Corporation 80ZC by users. Manuals are usually written by a technical writer, but in a language understandable to all users of New Buck Corporation 80ZC.

A complete New Buck Corporation manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual New Buck Corporation 80ZC - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the New Buck Corporation 80ZC, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the New Buck Corporation 80ZC, that we can find in the current document
3. Tips how to use the basic functions of the device New Buck Corporation 80ZC - which should help us in our first steps of using New Buck Corporation 80ZC
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with New Buck Corporation 80ZC
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of New Buck Corporation 80ZC in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning New Buck Corporation 80ZC?

Use the form below

If you did not solve your problem by using a manual New Buck Corporation 80ZC, ask a question using the form below. If a user had a similar problem with New Buck Corporation 80ZC it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)