Bedienungsanleitung Delta Electronics IPM- C Series

16 Seiten 0.58 mb
Download

Zur Seite of 16

Summary
  • Delta Electronics IPM- C Series - page 1

    1 Delta Electronics, Inc. 1.0 Purpose This document guides the user in performing electronic measurements on an IPM POL (point of load) DC/DC converter using the Delt a Evaluation Board. 2.0 Relevant Document ation The documentation and background information listed below is relevant to this evaluation procedure: ․ Applicative date sheet s for IP ...

  • Delta Electronics IPM- C Series - page 2

    3.0 Equipment Required ․ DC Power Supply 0 - 20 V @ 0 - 20A (Agilent 6574A 0 -60V/0 - 35A or equivalent). ․ Oscilloscope (T ektronix TDS 460A or equivalent) 4 Channel 400 MHz, equipped with a x1 scope probe, a x10 scope probe, and tw o BNC cables (length less than 20 inches/500mm) ․ Digital multimeters, one with 20A range and ideally all with ...

  • Delta Electronics IPM- C Series - page 3

    4.1 Connect one lead from the “+” lead of the power supply to the “20A” terminal of the first 4.2 Connect one wire from the “-” lead of the power supply (Item 3.1) to the “Vin-“ pin of the 4.3 Connect the plus “+” and minus “-“ connection leads from a second multimeter to the “SV in+” 4.4 Connect the plus “+” and min ...

  • Delta Electronics IPM- C Series - page 4

    6.0 T est s Performed performed at room temperature (+25 C). 6.1  Input V oltage Range. ut. . 6.2 O  Line Regulation. . t-Point Adjustment Range. 6.3 D Maximum Output V oltage Deviation (due to step change in load). 6.4 Efficiency e part number of the po wer module to determine that the correct module is being evaluated. Note: IPM12C0A0 S 04A ...

  • Delta Electronics IPM- C Series - page 5

    6) ed for the trim-down or trim-up setting of the Output V oltage. For IPM, if the converter requires a trim up, set SW3 to the T rim-up position. If the converter requires a 7) l resistors. For IPM12C0A0R04A, if the converter requires a tr im-up to 5V , set the SW4_1 8) rim-up, set the SW4_2 to ON position and SW3 to trim-up position. If the conve ...

  • Delta Electronics IPM- C Series - page 6

    7.2 Initial Power Up supply ON, set the current limit on power supply (refer to specification of either converter) and increase the input volt age (use DMM2 to monitor the volt age) until it 2) 3) ing, which can be verified by observing the DMM3 (appropriate ope (appropriate value 4) 8.0 T est s and Evaluation nge and Under-V olt age Lockout d from ...

  • Delta Electronics IPM- C Series - page 7

    8.2 Output Characteristics Line Regulation Deviation is defined as the change in output volt age caused by varying the ied range while the output load and temperature remain const ant. 2 Set the output power to the desired operating point. t the switch SW1 to the “OFF” position to enable the converter . 8.2.1 Line Regulation input voltage over ...

  • Delta Electronics IPM- C Series - page 8

    .2.4 Output V oltage Set-Point Adjustment Range (T rim) utput V oltage Set-Point Adjustment can be carried out by using an external resistor or e set-point (please refer to ments to Item 7.1-6, ries between the TRIM pin and ground. For IPM12C0A0R04A, Please refer to the IPMR t able for the desired trim-up can be calculated by the following equation ...

  • Delta Electronics IPM- C Series - page 9

    For I M04C series o implement T rim-up by using an external resistor , R trim-up must be connected between the d. For IPM04C0A0R06A, Please refer to the IPMR t able for the desired 9 P T TRIM pin and groun V out. The value of R trim-up can be calculated by the following equation and the datasheet can also be referred for further information. Ω ? ...

  • Delta Electronics IPM- C Series - page 10

    (2) Output V oltage Set-Point Adjustment by using an external voltage source For IPM12C series Output voltage of IPM12C is programmable while applying a voltage between the TRIM and GND pins. The following equation can be used to determine the value of Vtrim needed for a desired output voltage Vo: Vtrim = 0.7439 – 0.0488Vo Vtrim is the external v ...

  • Delta Electronics IPM- C Series - page 11

    11 8.3 Dynamic Characteristics 8.3.1 Output V olt age Deviation Output V oltage Deviation is defined as the response of the converter to a sudden step change in the output load current. The output volt age deviation is characterized by two parameters: Maximum Output V olt age Deviation and Response Time (please refer to the dat a sheet for the deta ...

  • Delta Electronics IPM- C Series - page 12

    T est (T urn on the module by using the external switch) 1) T urn on the fan. 2) T urn on the input power supply and set it to the desired operating point. 3) Set channel 1 on the oscilloscope to be DC coupled and to the appropriate range for the input voltage. 4) Connect a coaxial cable from channel 1 to BNC1 on the Evaluation Board. 5) Set channe ...

  • Delta Electronics IPM- C Series - page 13

    7) Use the following formulas to calculate the efficiency: Efficiency= (P out/Pin) × 100(%) Pin = Iin × V in Pout = Iout × V out For IPM12C series The following graph shows the efficiency result s of the IPM12C0A0R04A converter measured at different operating point s, the output voltage was set at 5V . 70 80 90 100 12 3 LOAD (A) EF F I C I EN C ...

  • Delta Electronics IPM- C Series - page 14

    14 Appendix A- Evaluation Board Schematic ...

  • Delta Electronics IPM- C Series - page 15

    15 Appendix B - Evaluation Board Layout (Top View) ...

  • Delta Electronics IPM- C Series - page 16

    Appendix C - Evaluation Bo ard Layout (Bottom View) CONTACT: www.delta.com.tw/dcdc USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: DCDC@delta-corp.com Europe: Phone: +41 31 998 53 11 Fax: +41 31 998 53 53 Email: DCDC@delta-es.com Asia & the rest of world: Telephone: +886 3 45 26107 ext 6220 Fax: ...

Produzent Delta Electronics Kategorie Power Supply

Dokumente, die wir vom Produzenten des Geräts Delta Electronics IPM- C Series erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Delta Electronics
- Bedienungsanleitungen IPM- C Series
- Produktkarten Delta Electronics
- Informationsbroschüren
- oder Energieetiketten Delta Electronics IPM- C Series
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Delta Electronics IPM- C Series.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Delta Electronics IPM- C Series, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Delta Electronics IPM- C Series. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Delta Electronics IPM- C Series ansehen.

Die komplette Bedienungsanleitung des Geräts Delta Electronics IPM- C Series, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Delta Electronics IPM- C Series hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Delta Electronics IPM- C Series verständlich ist.

Eine gänzliche Bedienungsanleitung von Delta Electronics sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Delta Electronics IPM- C Series bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Delta Electronics IPM- C Series befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Delta Electronics IPM- C Series, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Delta Electronics IPM- C Series - die uns die ersten Schritte während der Nutzung von Delta Electronics IPM- C Series erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Delta Electronics IPM- C Series hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Delta Electronics IPM- C Series im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Delta Electronics IPM- C Series?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Delta Electronics IPM- C Series nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Delta Electronics IPM- C Series hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)