English dropdown-ico

Manual Delta Electronics IPM- C Series

16 pages 0.58 mb
Download

Go to site of 16

Summary
  • Delta Electronics IPM- C Series - page 1

    1 Delta Electronics, Inc. 1.0 Purpose This document guides the user in performing electronic measurements on an IPM POL (point of load) DC/DC converter using the Delt a Evaluation Board. 2.0 Relevant Document ation The documentation and background information listed below is relevant to this evaluation procedure: ․ Applicative date sheet s for IP ...

  • Delta Electronics IPM- C Series - page 2

    3.0 Equipment Required ․ DC Power Supply 0 - 20 V @ 0 - 20A (Agilent 6574A 0 -60V/0 - 35A or equivalent). ․ Oscilloscope (T ektronix TDS 460A or equivalent) 4 Channel 400 MHz, equipped with a x1 scope probe, a x10 scope probe, and tw o BNC cables (length less than 20 inches/500mm) ․ Digital multimeters, one with 20A range and ideally all with ...

  • Delta Electronics IPM- C Series - page 3

    4.1 Connect one lead from the “+” lead of the power supply to the “20A” terminal of the first 4.2 Connect one wire from the “-” lead of the power supply (Item 3.1) to the “Vin-“ pin of the 4.3 Connect the plus “+” and minus “-“ connection leads from a second multimeter to the “SV in+” 4.4 Connect the plus “+” and min ...

  • Delta Electronics IPM- C Series - page 4

    6.0 T est s Performed performed at room temperature (+25 C). 6.1  Input V oltage Range. ut. . 6.2 O  Line Regulation. . t-Point Adjustment Range. 6.3 D Maximum Output V oltage Deviation (due to step change in load). 6.4 Efficiency e part number of the po wer module to determine that the correct module is being evaluated. Note: IPM12C0A0 S 04A ...

  • Delta Electronics IPM- C Series - page 5

    6) ed for the trim-down or trim-up setting of the Output V oltage. For IPM, if the converter requires a trim up, set SW3 to the T rim-up position. If the converter requires a 7) l resistors. For IPM12C0A0R04A, if the converter requires a tr im-up to 5V , set the SW4_1 8) rim-up, set the SW4_2 to ON position and SW3 to trim-up position. If the conve ...

  • Delta Electronics IPM- C Series - page 6

    7.2 Initial Power Up supply ON, set the current limit on power supply (refer to specification of either converter) and increase the input volt age (use DMM2 to monitor the volt age) until it 2) 3) ing, which can be verified by observing the DMM3 (appropriate ope (appropriate value 4) 8.0 T est s and Evaluation nge and Under-V olt age Lockout d from ...

  • Delta Electronics IPM- C Series - page 7

    8.2 Output Characteristics Line Regulation Deviation is defined as the change in output volt age caused by varying the ied range while the output load and temperature remain const ant. 2 Set the output power to the desired operating point. t the switch SW1 to the “OFF” position to enable the converter . 8.2.1 Line Regulation input voltage over ...

  • Delta Electronics IPM- C Series - page 8

    .2.4 Output V oltage Set-Point Adjustment Range (T rim) utput V oltage Set-Point Adjustment can be carried out by using an external resistor or e set-point (please refer to ments to Item 7.1-6, ries between the TRIM pin and ground. For IPM12C0A0R04A, Please refer to the IPMR t able for the desired trim-up can be calculated by the following equation ...

  • Delta Electronics IPM- C Series - page 9

    For I M04C series o implement T rim-up by using an external resistor , R trim-up must be connected between the d. For IPM04C0A0R06A, Please refer to the IPMR t able for the desired 9 P T TRIM pin and groun V out. The value of R trim-up can be calculated by the following equation and the datasheet can also be referred for further information. Ω ? ...

  • Delta Electronics IPM- C Series - page 10

    (2) Output V oltage Set-Point Adjustment by using an external voltage source For IPM12C series Output voltage of IPM12C is programmable while applying a voltage between the TRIM and GND pins. The following equation can be used to determine the value of Vtrim needed for a desired output voltage Vo: Vtrim = 0.7439 – 0.0488Vo Vtrim is the external v ...

  • Delta Electronics IPM- C Series - page 11

    11 8.3 Dynamic Characteristics 8.3.1 Output V olt age Deviation Output V oltage Deviation is defined as the response of the converter to a sudden step change in the output load current. The output volt age deviation is characterized by two parameters: Maximum Output V olt age Deviation and Response Time (please refer to the dat a sheet for the deta ...

  • Delta Electronics IPM- C Series - page 12

    T est (T urn on the module by using the external switch) 1) T urn on the fan. 2) T urn on the input power supply and set it to the desired operating point. 3) Set channel 1 on the oscilloscope to be DC coupled and to the appropriate range for the input voltage. 4) Connect a coaxial cable from channel 1 to BNC1 on the Evaluation Board. 5) Set channe ...

  • Delta Electronics IPM- C Series - page 13

    7) Use the following formulas to calculate the efficiency: Efficiency= (P out/Pin) × 100(%) Pin = Iin × V in Pout = Iout × V out For IPM12C series The following graph shows the efficiency result s of the IPM12C0A0R04A converter measured at different operating point s, the output voltage was set at 5V . 70 80 90 100 12 3 LOAD (A) EF F I C I EN C ...

  • Delta Electronics IPM- C Series - page 14

    14 Appendix A- Evaluation Board Schematic ...

  • Delta Electronics IPM- C Series - page 15

    15 Appendix B - Evaluation Board Layout (Top View) ...

  • Delta Electronics IPM- C Series - page 16

    Appendix C - Evaluation Bo ard Layout (Bottom View) CONTACT: www.delta.com.tw/dcdc USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: DCDC@delta-corp.com Europe: Phone: +41 31 998 53 11 Fax: +41 31 998 53 53 Email: DCDC@delta-es.com Asia & the rest of world: Telephone: +886 3 45 26107 ext 6220 Fax: ...

Manufacturer Delta Electronics Category Power Supply

Documents that we receive from a manufacturer of a Delta Electronics IPM- C Series can be divided into several groups. They are, among others:
- Delta Electronics technical drawings
- IPM- C Series manuals
- Delta Electronics product data sheets
- information booklets
- or energy labels Delta Electronics IPM- C Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta Electronics IPM- C Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta Electronics IPM- C Series, service manual, brief instructions and user manuals Delta Electronics IPM- C Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta Electronics IPM- C Series.

Similar manuals

A complete manual for the device Delta Electronics IPM- C Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta Electronics IPM- C Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta Electronics IPM- C Series.

A complete Delta Electronics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta Electronics IPM- C Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta Electronics IPM- C Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta Electronics IPM- C Series, that we can find in the current document
3. Tips how to use the basic functions of the device Delta Electronics IPM- C Series - which should help us in our first steps of using Delta Electronics IPM- C Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta Electronics IPM- C Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta Electronics IPM- C Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta Electronics IPM- C Series?

Use the form below

If you did not solve your problem by using a manual Delta Electronics IPM- C Series, ask a question using the form below. If a user had a similar problem with Delta Electronics IPM- C Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)