Bedienungsanleitung Whirlpool WSR413YW0

18 Seiten 1.58 mb
Download

Zur Seite of 18

Summary
  • Whirlpool WSR413YW0 - page 1

    b& ChIJ Inst’dfat ion Instructions WHIRLPOOL UNDERCOUNTER REVERSE OSMOSIS WATER FILTRATION SYSTEM IV ...

  • Whirlpool WSR413YW0 - page 2

    Remove parts from packages. Check that you have all the parts. storage tank with base (A) filtration assembly cover (B) two mounting screws (C) g-volt battery (D) filtration assembly (E) 3/e” blue tubing (F) l/4” yellow tubing (G) l/4” orange tubing (H) RO membrane cartridge (I) I n %” red tubing wiih push-in connector attached (K) l/4” g ...

  • Whirlpool WSR413YW0 - page 3

    Before You Start . . . HOOK UP WATER I L, IMPORTANT: Read and save these instructions. It is recommended that this system be installed by a licensed plumber. It is the responsibility of the installer to comply with the installation specifications provided and with state and local plumbing codes. If you decided to install the system yourself, see ? ...

  • Whirlpool WSR413YW0 - page 4

    - - Instructions At A Glance l For detailed instructions see following page. 1. Turn off cold water supply. (Steps la-lb) 3. Connect saddle valve to cold water supply. (Steps We or 1 h-lj) 2. Turn on faucet to drain water from line. (Step 1 b) 4. Turn saddle valve handle clockwise until piercing lance enters pope and stops. (Steps If-19 or 1 k-l I) ...

  • Whirlpool WSR413YW0 - page 5

    Product Damage DO NOT connect to a hot water supply line. Failure to follow this instruction could result in product damage. la Take note of water requirements listed . under the Use & Care section of this booklet. The filtration system’s feed line (orange tubing) connects to your cold water supply line using the saddle valve. Do not use sadd ...

  • Whirlpool WSR413YW0 - page 6

    Instructions At A Glance l For detailed I. Connect faucet spout, chrome base plate, indicator light disk and rubber washer to faucet base. (Steps 2a-2b) nstructions see following page. 2. Connect green tubing and black tubing to faucet. (Steps 2c-2d) 3. Place faucet in sink opening. Secure faucet to sink 4. Connect faucet indicator wire to wire har ...

  • Whirlpool WSR413YW0 - page 7

    Front view of air gap faucet _ chrome base elate indicator - light wire t ;fby;; Fhex nut Is- %” grey connector with push-in end Side view of air gap faucet k spout air gap hole slnk %” tubing black %” tubing must ;lor; downward to blue %” tubing Property Damage l Contact a qualified installer or licensed plumber for cutting a faucet openin ...

  • Whirlpool WSR413YW0 - page 8

    Instructions At A Glance l For detailed instructions see following page. 1. Install RO cartridge into filtration assembly. Connect one end of red tubing to bottom of RO cartridge. Connect other end to green tubing from faucet. (Steps 3a-3e) 3. Use orange tubing from filtration assembly to fill storage tank with water. (Steps 3g-3h) Connect orange t ...

  • Whirlpool WSR413YW0 - page 9

    The filtration assembly should already be . placed close to its final location. Move storage tank near its final location, which should be within four feet of filtration assembly. The filtration assembly may be installed under a sink or in the basement (mounted to wood floor supports or to the basement wall). For basement installation order Basemen ...

  • Whirlpool WSR413YW0 - page 10

    Instructions At A Glance l For detailed instructions see following page. 1. Decide where drain saddle will be mounted. w , The best place is on a horizontal drain tailpiece I above (before) the trap. (Steps 4a-4b) , 2. Connect drain saddle to drain pipe. (Step 4c) 3. Drill hole in drain using o drain saddle as a guide. ( t ening in tep 4d) 4. Threa ...

  • Whirlpool WSR413YW0 - page 11

    Electrical Shock Hazard Special care must be taken when drilling into water pipes. Some water may remain in pipe. - If an electric drill is used, it must be properly grounded to prevent severe or lethal shock if water should enter drill. Use only an electric drill with a 3-wire power supply cord connected to a grounded receptacle. l Check with a qu ...

  • Whirlpool WSR413YW0 - page 12

    Flush System Instructions At A Glance l For detailed instructions see following page. I. Slide filtration assembly onto mounting screws. 2. Turn on faucet and drain tank to flush (Step 5a) disinfectant from tank. (Step 5b) 3. Turn on cold water supply and saddle valve. (Step 5c) 4. Allow tank to fill - ap roximately 4 hours. Lift faucet handle to d ...

  • Whirlpool WSR413YW0 - page 13

    Flush System 5a Slide filtration asse . mounting holes onto mounting screws that were installed in step 3b. DO NOT kink or bend tubing. Insulated staples may be used to secure tubing to cabinet walls. Tighten mount- ing screws to secure filtration assembly to wall. Replace fil- tration assembly cover. 5b In step 3h you filled the storage tank with ...

  • Whirlpool WSR413YW0 - page 14

    Water Requirements The filtration system must be connected to a cold water supply line providing 40-l 00 psi water pressure. If psi is less than 40, a booster pump, (Part Number 4373525) will be needed. Review the water application guideline chart below to determine if your water meets the standards necessary to use this water filtration system. DO ...

  • Whirlpool WSR413YW0 - page 15

    Using your RO water filtration system To get purified water from the storage tank - Hold the faucet handle down for momentary flow, hold the faucet up for continuous flow. To stop water flow from the faucet - Return the faucet to the center or horizontal position. When faucet flow slows or drips - The storage tank is empty. Wait 1 hour before dispe ...

  • Whirlpool WSR413YW0 - page 16

    How to sanitize the storage tank You will need to order Tank Sanitizing Kit, Part No. 4373527. You will also need household bleach and a measuring spoon. 1. Turn off saddle valve in water line. Open faucet and drain storage tank. There will be no water dripping when tank is empty. 2. Turn off faucet. Push in grey connector to disconnect yellow tubi ...

  • Whirlpool WSR413YW0 - page 17

    Performance Data Sheet @ Q This Reverse Osmosis System has been tested and listed by NSF International under Standard 58 for the water treatment claims listed below under “Contaminant Reduction Performance”. Whirlpool Reverse Osmosis Water Filtration System IV Model No. WSR413YW Test Parameters TDS = 200500 mg/L2 pH = 7.5 Turbidity = 1 NTU Temp ...

  • Whirlpool WSR413YW0 - page 18

    Part No. 4373500 Rev B 01993 Whirlpool Corporation Whirlpool Corporation Benton Harbor, MI 49022 @ Printed on Recycled Paper in U.S.A. ...

Produzent Whirlpool Kategorie Water Dispenser

Dokumente, die wir vom Produzenten des Geräts Whirlpool WSR413YW0 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Whirlpool
- Bedienungsanleitungen WSR413YW0
- Produktkarten Whirlpool
- Informationsbroschüren
- oder Energieetiketten Whirlpool WSR413YW0
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Whirlpool WSR413YW0.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Whirlpool WSR413YW0, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Whirlpool WSR413YW0. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Whirlpool WSR413YW0 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Whirlpool WSR413YW0, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Whirlpool WSR413YW0 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Whirlpool WSR413YW0 verständlich ist.

Eine gänzliche Bedienungsanleitung von Whirlpool sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Whirlpool WSR413YW0 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Whirlpool WSR413YW0 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Whirlpool WSR413YW0, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Whirlpool WSR413YW0 - die uns die ersten Schritte während der Nutzung von Whirlpool WSR413YW0 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Whirlpool WSR413YW0 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Whirlpool WSR413YW0 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Whirlpool WSR413YW0?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Whirlpool WSR413YW0 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Whirlpool WSR413YW0 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)