Bedienungsanleitung Honeywell TH4110D

16 Seiten 0.63 mb
Download

Zur Seite of 16

Summary
  • Honeywell TH4110D - page 1

    Installation Guide TH4110D Programmable Thermostat ...

  • Honeywell TH4110D - page 2

    Product Application This thermostat provides electronic control of 24 V A C single-stage heating and cool- ing systems, or 750 mV heating systems. System T ypes • Gas, oil, or electric heat with air conditioning • W arm air , hot water , high-efficiency furnaces, heat pumps, steam, gravi- ty • Heat only • Heat only with f an • Cool only ? ...

  • Honeywell TH4110D - page 3

    PRO TH4110D Programmable Thermostat 1 Install the thermostat about 5 feet (1.5m) above the floor in an area with good air circulation at average temperatur e. Do not install in locations where the thermostat can be af fected by: • Drafts or dead spots behind doors and in corners • Hot or cold air from ducts • Sunlight or radiant heat from app ...

  • Honeywell TH4110D - page 4

    Installation Guide 2 Pre-installation checklist Package contents Check to make sure y our package includes the f ollowing items: • PR O TH4110D digital thermostat (wallplate attached to back) • Operating manual • W all anchors and mounting screws (2 eac h) • AA alkaline batteries (2) • Quick ref erence card Required tools & supplies ? ...

  • Honeywell TH4110D - page 5

    PRO TH4110D Programmable Thermostat 3 W allplate installation Remove the w allplate from the ther- mostat as shown at left, then f ollow directions below f or mounting. 1 Pull wires through wire hole. 2 P osition wallplate on wall, level and mark hole positions with pencil. 3 Drill holes at marked positions as shown below , then tap in supplied wal ...

  • Honeywell TH4110D - page 6

    Installation Guide 4 Wiring 1 Loosen screw terminals, insert wires into terminal block, then re- tighten screws. 2 Push e xcess wire back into the wall opening. K eep wires in shaded area as shown at left. 3 Plug the wall opening with non- f lamma ble insulation to pr event drafts from affecting thermostat operation. T erminal Designations W W Heat ...

  • Honeywell TH4110D - page 7

    PRO TH4110D Programmable Thermostat 5 T ypical 1H/1C system: 1 transformer T ypical 1H/1C system: 2 transformers 1 Power supply . Provide disconnect means and overload pr otection as required. 2 Factory-installed jumper . Remove for 2-transformer systems only . 3 Use either O or B terminals for changeover valve. 4 Use a small piece of wire (not sup ...

  • Honeywell TH4110D - page 8

    Installation Guide 6 • G G a a s s o o r r O O i i l l : : For gas or oil heating systems, leave the f an operation switc h in this factor y-set position (This setting is for systems that control the fan in a call f or heat.) • E E l l e e c c t t r r i i c c o o r r H H e e a a t t P P u u m m p p : : Change the switc h to this setting for hea ...

  • Honeywell TH4110D - page 9

    PRO TH4110D Programmable Thermostat 7 AC Power The thermostat can be powered by 24 V A C power , or by batter ies. T o wire the thermostat for A C power , connect the common side of the cooling transf or mer to the “C” terminal as shown at left. I I m m p p o o r r t t a a n n t t : : Remove R/Rc jumper f or 2-transf or mer systems onl y . (See ...

  • Honeywell TH4110D - page 10

    1 0 Installation Guide 8 1 5 9 13 14 15 System type Heating cycle rate (CPH: cycles/hour) Compressor cycle rate (CPH) Adaptive Intelligent Recovery T emperature display Compressor protection 0 Gas, oil or electric heat with air conditioning 1 Heat pump (5 minute compressor of f time in heating and cooling) 5 For gas or oil furnaces of less than 90% ...

  • Honeywell TH4110D - page 11

    PRO TH4110D Programmable Thermostat 9 10 0 T est 10 30 70 Heating system Cooling system Thermostat information (for refer ence only) 0 Heat and fan turn off. 1 Heat turns on. Fan also turns on immediately if Fan Operation Switch is set to Electric Heat/Heat Pump (see page 6). 0 Compressor and fan turn off. 1 Compressor and fan turn on. 71 Software ...

  • Honeywell TH4110D - page 12

    Installation Guide 10 Built-in compressor pr otection (Setup Function 15) This featur e helps prevent damag e to the compressor in the air conditioning or heat pump system. Damage can occur if the compressor is r e- started too soon after shutdown. This feature for ces the compressor to wait f or a few minutes befor e restarting. During the wait ti ...

  • Honeywell TH4110D - page 13

    PRO TH4110D Programmable Thermostat 11 Quick refer ence to controls • Set: Press to set time/day/ schedule • Hold: Press to override programmed temperatur e control. • Run: Press to r esume program schedule System switch • Cool: Thermostat controls only the cooling system. • Heat: Thermostat controls only the heating system. • Off: Heat ...

  • Honeywell TH4110D - page 14

    Installation Guide 12 In case of difficulty If you hav e dif ficulty with your thermostat, please tr y the sugg estions below . Most problems can be corrected quickl y and easily . Display is blank • Check circuit br eaker and reset if necessary . • Make sure heating & cooling power switches ar e on. • Make sure equipment door is secur el ...

  • Honeywell TH4110D - page 15

    PRO TH4110D Programmable Thermostat 13 Accessories Please contact your distributor to order accessories. Cover plate assembly ............................................Part Number 50002883-001 (Used to cover marks left by old thermostats.) Specifications T emperature Ranges • Heat: 40° to 90°F (4.5° to 32°C) • Cool: 50° to 99°F (10° to ...

  • Honeywell TH4110D - page 16

    Honeywell International Inc. 1985 Douglas Drive North Golden V alley , MN 55422 http://yourhome.honeywell.com Automation and Control Solutions Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered T rademark. © 2005 Honeywell International Inc. Patents pending. All rights reserved. 69-1849 • 0 ...

Produzent Honeywell Kategorie Thermostat

Dokumente, die wir vom Produzenten des Geräts Honeywell TH4110D erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Honeywell
- Bedienungsanleitungen TH4110D
- Produktkarten Honeywell
- Informationsbroschüren
- oder Energieetiketten Honeywell TH4110D
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Honeywell TH4110D.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Honeywell TH4110D, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Honeywell TH4110D. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Honeywell TH4110D ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Honeywell TH4110D, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Honeywell TH4110D hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Honeywell TH4110D verständlich ist.

Eine gänzliche Bedienungsanleitung von Honeywell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Honeywell TH4110D bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Honeywell TH4110D befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Honeywell TH4110D, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Honeywell TH4110D - die uns die ersten Schritte während der Nutzung von Honeywell TH4110D erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Honeywell TH4110D hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Honeywell TH4110D im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Honeywell TH4110D?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Honeywell TH4110D nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Honeywell TH4110D hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)