Manuale per l’uso Honeywell TH4110D

16 pagine 0.63 mb
Scarica

Vai alla pagina of 16

Summary
  • Honeywell TH4110D - page 1

    Installation Guide TH4110D Programmable Thermostat ...

  • Honeywell TH4110D - page 2

    Product Application This thermostat provides electronic control of 24 V A C single-stage heating and cool- ing systems, or 750 mV heating systems. System T ypes • Gas, oil, or electric heat with air conditioning • W arm air , hot water , high-efficiency furnaces, heat pumps, steam, gravi- ty • Heat only • Heat only with f an • Cool only ? ...

  • Honeywell TH4110D - page 3

    PRO TH4110D Programmable Thermostat 1 Install the thermostat about 5 feet (1.5m) above the floor in an area with good air circulation at average temperatur e. Do not install in locations where the thermostat can be af fected by: • Drafts or dead spots behind doors and in corners • Hot or cold air from ducts • Sunlight or radiant heat from app ...

  • Honeywell TH4110D - page 4

    Installation Guide 2 Pre-installation checklist Package contents Check to make sure y our package includes the f ollowing items: • PR O TH4110D digital thermostat (wallplate attached to back) • Operating manual • W all anchors and mounting screws (2 eac h) • AA alkaline batteries (2) • Quick ref erence card Required tools & supplies ? ...

  • Honeywell TH4110D - page 5

    PRO TH4110D Programmable Thermostat 3 W allplate installation Remove the w allplate from the ther- mostat as shown at left, then f ollow directions below f or mounting. 1 Pull wires through wire hole. 2 P osition wallplate on wall, level and mark hole positions with pencil. 3 Drill holes at marked positions as shown below , then tap in supplied wal ...

  • Honeywell TH4110D - page 6

    Installation Guide 4 Wiring 1 Loosen screw terminals, insert wires into terminal block, then re- tighten screws. 2 Push e xcess wire back into the wall opening. K eep wires in shaded area as shown at left. 3 Plug the wall opening with non- f lamma ble insulation to pr event drafts from affecting thermostat operation. T erminal Designations W W Heat ...

  • Honeywell TH4110D - page 7

    PRO TH4110D Programmable Thermostat 5 T ypical 1H/1C system: 1 transformer T ypical 1H/1C system: 2 transformers 1 Power supply . Provide disconnect means and overload pr otection as required. 2 Factory-installed jumper . Remove for 2-transformer systems only . 3 Use either O or B terminals for changeover valve. 4 Use a small piece of wire (not sup ...

  • Honeywell TH4110D - page 8

    Installation Guide 6 • G G a a s s o o r r O O i i l l : : For gas or oil heating systems, leave the f an operation switc h in this factor y-set position (This setting is for systems that control the fan in a call f or heat.) • E E l l e e c c t t r r i i c c o o r r H H e e a a t t P P u u m m p p : : Change the switc h to this setting for hea ...

  • Honeywell TH4110D - page 9

    PRO TH4110D Programmable Thermostat 7 AC Power The thermostat can be powered by 24 V A C power , or by batter ies. T o wire the thermostat for A C power , connect the common side of the cooling transf or mer to the “C” terminal as shown at left. I I m m p p o o r r t t a a n n t t : : Remove R/Rc jumper f or 2-transf or mer systems onl y . (See ...

  • Honeywell TH4110D - page 10

    1 0 Installation Guide 8 1 5 9 13 14 15 System type Heating cycle rate (CPH: cycles/hour) Compressor cycle rate (CPH) Adaptive Intelligent Recovery T emperature display Compressor protection 0 Gas, oil or electric heat with air conditioning 1 Heat pump (5 minute compressor of f time in heating and cooling) 5 For gas or oil furnaces of less than 90% ...

  • Honeywell TH4110D - page 11

    PRO TH4110D Programmable Thermostat 9 10 0 T est 10 30 70 Heating system Cooling system Thermostat information (for refer ence only) 0 Heat and fan turn off. 1 Heat turns on. Fan also turns on immediately if Fan Operation Switch is set to Electric Heat/Heat Pump (see page 6). 0 Compressor and fan turn off. 1 Compressor and fan turn on. 71 Software ...

  • Honeywell TH4110D - page 12

    Installation Guide 10 Built-in compressor pr otection (Setup Function 15) This featur e helps prevent damag e to the compressor in the air conditioning or heat pump system. Damage can occur if the compressor is r e- started too soon after shutdown. This feature for ces the compressor to wait f or a few minutes befor e restarting. During the wait ti ...

  • Honeywell TH4110D - page 13

    PRO TH4110D Programmable Thermostat 11 Quick refer ence to controls • Set: Press to set time/day/ schedule • Hold: Press to override programmed temperatur e control. • Run: Press to r esume program schedule System switch • Cool: Thermostat controls only the cooling system. • Heat: Thermostat controls only the heating system. • Off: Heat ...

  • Honeywell TH4110D - page 14

    Installation Guide 12 In case of difficulty If you hav e dif ficulty with your thermostat, please tr y the sugg estions below . Most problems can be corrected quickl y and easily . Display is blank • Check circuit br eaker and reset if necessary . • Make sure heating & cooling power switches ar e on. • Make sure equipment door is secur el ...

  • Honeywell TH4110D - page 15

    PRO TH4110D Programmable Thermostat 13 Accessories Please contact your distributor to order accessories. Cover plate assembly ............................................Part Number 50002883-001 (Used to cover marks left by old thermostats.) Specifications T emperature Ranges • Heat: 40° to 90°F (4.5° to 32°C) • Cool: 50° to 99°F (10° to ...

  • Honeywell TH4110D - page 16

    Honeywell International Inc. 1985 Douglas Drive North Golden V alley , MN 55422 http://yourhome.honeywell.com Automation and Control Solutions Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered T rademark. © 2005 Honeywell International Inc. Patents pending. All rights reserved. 69-1849 • 0 ...

Fabbricante Honeywell Categoria Thermostat

I documenti che otteniamo dal fabbricante del dispositivoHoneywell TH4110D possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Honeywell
- manuali per l’uso TH4110D
- schede prodotto Honeywell
- opuscoli
- o etichette energetiche Honeywell TH4110D
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Honeywell TH4110D.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Honeywell TH4110D, manuali di manutenzione, brevi manuali o manuali utente Honeywell TH4110D. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Honeywell TH4110D.

Manuale completo del dispositivo Honeywell TH4110D, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Honeywell TH4110D dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Honeywell TH4110D.

Il manuale per l’uso completo Honeywell, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Honeywell TH4110D - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Honeywell TH4110D, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Honeywell TH4110D che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Honeywell TH4110D - che ci dovrebbe aiutare nei primi passi durante l'uso Honeywell TH4110D
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Honeywell TH4110D
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Honeywell TH4110D in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Honeywell TH4110D?

Utilizza il modulo sottostante

Se non hai risolto il problema con Honeywell TH4110D con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Honeywell TH4110D è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)