Bedienungsanleitung Tannoy Highline 500

20 Seiten 1.85 mb
Download

Zur Seite of 20

Summary
  • Tannoy Highline 500 - page 1

    OWNER’ S MANUAL ...

  • Tannoy Highline 500 - page 2

    CONTENTS INTRODUCTION 3 SA TELLITE What’ s in the box? 4 How to wall mount 5 ST AND MOUNT What's in the box? 8 How to stand mount 9 CENTRE CHANNEL What’ s in the box? 10 How to wall mount 1 1 TOWER What’ s in the box? 13 How to connect 14 ROOM SET UP 15 CONNECT TO RECEIVER 16 SPECIFICA TIONS 17 W ARRANTY This equipment has been produced ...

  • Tannoy Highline 500 - page 3

    INTRODUCTION Thank you for selecting T annoy loudspeakers developed in the UK by our dedicated team of design engineers. The T annoy Arena Highline 500™ speakers are designed to blend perfectly into your room and provide a sound stage which is at least as good as you would hear in a commercial movie theatre, but in the comfort of your own home. Y ...

  • Tannoy Highline 500 - page 4

    SA TELLITE Wha t’s in the box? 1 x Satellite speaker 1 x Long wall bracket 1 x Short bracket with pre-fitted cap 1 x Short bracket without pre-fitted cap 1 x Bracket cap 4 x 8mm Silver hex socket fixing screw + lock washers 1 x 5mm black cap head fixing screw + spring washer 1 x Ball nosed Allen key Required but not included: Sufficient cable for ...

  • Tannoy Highline 500 - page 5

    SATELLITE How to wall mount WARNING: It is your responsibility to ensure that the bracket to wall fixing screws or bolts and the walls themselves are strong enough to support the weight of the speaker – refer to the speaker weight specifications supplied in this manual. Particular care is needed when fixing to hollow or cavity walls - ‘'st ...

  • Tannoy Highline 500 - page 6

    SA TELLITE How to wall mount - continued Cut the speaker wire so that the (+) side is slightly longer than the (-) side and feed the speaker wire through spare bracket cap. Important Note: It is essential that the speakers are wired correctly at this stage. The (-) wire should have a solid black line, or similar , marked along it. Screw (+) wire in ...

  • Tannoy Highline 500 - page 7

    SATELLITE How to wall mount - continued Fix spare cap to bottom of bracket using cap screw and spring washer provided 7 ...

  • Tannoy Highline 500 - page 8

    8 ST AND MOUNT What’ s in the box? 1 x Stand mount 2 x Lock washers 2 x Fixing screws 6 x Spikes 6 x Rubber feet 6 x M6 nuts ...

  • Tannoy Highline 500 - page 9

    ST AND MOUNT How to stand mount Attach the spike kits, or rubber feet, to the bottom of the stand then thread the cable through the stand base and shaft. Cut the speaker wire so that the (+) wire is slightly longer than the (-) wire. Screw the (+) wire into the red terminal and screw (-) wire into black terminal. Important Note : It is essential th ...

  • Tannoy Highline 500 - page 10

    CENTRE CHANNEL What’s in the box? 1 x Centre speaker 1 x Long wall bracket 1 x Short bracket with pre-fitted cap 1 x Short bracket without pre-fitted cap 1 x Bracket cap 4 x 8mm Silver hex socket fixing screw + lock washers 1 x 5mm Black cap head fixing screw + spring washer 1 x Ball nosed allen key 1 x Small stand Required but not included: Suff ...

  • Tannoy Highline 500 - page 11

    CENTRE CHANNEL How to wall mount WARNING: It is your responsibility to ensure that the bracket to wall fixing screws or bolts and the walls themselves are strong enough to support the weight of the speaker - refer to the speaker weight specifications supplied in this manual. Particular care is needed when fixing to hollow or cavity walls - ‘&apos ...

  • Tannoy Highline 500 - page 12

    CENTRE CHANNEL How to wall mount - continued Offer the speaker up to the wall bracket half way along. Engage speaker with bracket and slide across. Ensure cap is fully engaged with the wall bracket. Fix spare cap to bottom of bracket using the cap screw and spring washer provided. 12 ...

  • Tannoy Highline 500 - page 13

    13 T OWER What’s in the box? 1 x Tower speaker 6 x Spikes 6 x Rubber Feet 6 x M6 Nuts Required but not included: Sufficient cable for your requirements ...

  • Tannoy Highline 500 - page 14

    TOWER How to connect Attach the spike kits or rubber feet to the base of the tower then thread the speaker cable through the base. Cut the speaker wire so that the (+) wire is slightly longer than the (-). Screw the (+) wire into the red terminal and screw (-) wire into the black terminal. Important Note : It is essential that the speakers are wire ...

  • Tannoy Highline 500 - page 15

    ROOM SETUP A 5.1 surround sound system consists of 5 separate speakers and 1 subwoofer. The centre channel is designed to reproduce most of the dialogue or solo performances. The front left and right speakers reproduce the left/right stereo information and special effects. The rear left and right speakers reproduce special effects. Try to get all 3 ...

  • Tannoy Highline 500 - page 16

    CONNECTING THE SYSTEM TO YOUR A V RECEIVER Wire up the system connecting each speaker to the appropriate terminals on the receiver or amplifier making sure that cables connect red to red terminals (+ to +) and black to black terminals (- to - ). Please note : (+) is shown as grey, (-) is shown as white. Take care to distinguish between left and rig ...

  • Tannoy Highline 500 - page 17

    TECHNICAL SPECIFICATIONS ARENA HIGHLINE 500, CENTRE & SATELLITE SPEAKER PERFORMANCE: Recommended amplifier power 25 - 100W RMS Maximum sensitivity (2.83V @ 1m) 88dB Nominal impedance 8 Ohm Frequency response (-6dB) 85Hz- 54kHz Drivers 1 x 100mm (4”) Dual Concentric TM with 19mm (0.75”) HF 1 x 100mm (4”) LF Crossover frequency 1.75kHz Magn ...

  • Tannoy Highline 500 - page 18

    209.0mm (8.23”) 197.0mm (7.76”) 759.5 (29.90”) 999.5 - 1 199.5mm (39.35” - 47.22”) TECHNICAL SPECIFICA TIONS ARENA HIGHLINE 500 SATELLITE ACCESSORY STAND Weight 5.9kg (13lbs) Dimensions H x W x D 760 x 209 x 197mm (29.90 x 8.23 x 7.76 ins) Finish Black gloss or silver gloss 18 ...

  • Tannoy Highline 500 - page 19

    209.0mm (8.23”) 197.0mm (7.76”) 1160.5mm (45.69”) TECHNICAL SPECIFICA TIONS ARENA HIGHLINE 500, TOWER SPEAKER PERFORMANCE: Recommended amplifier power 25 - 100W RMS Maximum sensitivity (2.83V @ 1m) 88dB Nominal impedance 8 Ohm s Frequency response (-6dB) 75Hz- 54kHz Drivers 1 x 100mm (4”) Dual Concentric TM with 19mm (0.75”) HF 1 x 100mm ...

  • Tannoy Highline 500 - page 20

    Check periodically for the latest manual revision that will always be available for download from www.tannoy.com The issue number of this manual is located below Part No. 6481 0481 / MAR 06 T annoy United Kingdom T : +44 (0) 1236 420199 F: +44 (0) 1236 428230 E: enquiries@tannoy .com T annoy North America T : (519) 745 1158 F: (519) 745 2364 E: inq ...

Produzent Tannoy Kategorie Portable Speaker

Dokumente, die wir vom Produzenten des Geräts Tannoy Highline 500 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Tannoy
- Bedienungsanleitungen Highline 500
- Produktkarten Tannoy
- Informationsbroschüren
- oder Energieetiketten Tannoy Highline 500
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Tannoy Highline 500.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Tannoy Highline 500, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Tannoy Highline 500. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Tannoy Highline 500 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Tannoy Highline 500, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Tannoy Highline 500 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Tannoy Highline 500 verständlich ist.

Eine gänzliche Bedienungsanleitung von Tannoy sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Tannoy Highline 500 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Tannoy Highline 500 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Tannoy Highline 500, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Tannoy Highline 500 - die uns die ersten Schritte während der Nutzung von Tannoy Highline 500 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Tannoy Highline 500 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Tannoy Highline 500 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Tannoy Highline 500?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Tannoy Highline 500 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Tannoy Highline 500 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)