Bedienungsanleitung Husqvarna K3600 MKII

24 Seiten 1.61 mb
Download

Zur Seite of 24

Summary
  • Husqvarna K3600 MKII - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h K3600 MKII Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine. ...

  • Husqvarna K3600 MKII - page 2

    2 – English KEY T O SYMBOLS K ey to symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ed pr ...

  • Husqvarna K3600 MKII - page 3

    English – 3 CONTENTS Contents KEY T O SYMBOLS K ey to symbols ............................................................. 2 CONTENTS Contents ...................................................................... 3 WHA T IS WHA T? What is what on the po wer cutter? ............................... 4 SAFETY INSTR UCTIONS Steps bef ore using a new ...

  • Husqvarna K3600 MKII - page 4

    4 – English WHA T IS WHA T? What is what on the po wer cutter? 1 Diamond blade 2 Blade guard/spra y guard 3 Hydraulic motor 4 Locking b utton f or the drive wheel 5 Grease nipples 6 Control f or the guide rollers 7 F ront handle (adjustable) 8 W ater adjustment control 9 Switch 10 W ater connector 11 Couplings f or hydr aulic hoses 12 Rating plat ...

  • Husqvarna K3600 MKII - page 5

    English – 5 SAFETY INSTR UCTIONS Steps bef ore using a new po wer cutter . • This machine is a h ydraulically operated po wer cutter intended f or free-hand cutting. The machine should be connected to a h ydraulic unit with an oil flow of 35-42 litres/min and a maximum pressure of 150 bar . • Please read the operator’ s manual carefully . ...

  • Husqvarna K3600 MKII - page 6

    6 – English SAFETY INSTR UCTIONS Switc h lock and ON/OFF v alve for the water The s witch lock is designed to pre vent accidental operation of the s witch. The ON/OFF valv e for the water supply is also controlled with the s witch lock. When the s witch lock (A) is pressed in this opens the w ater valv e and releases the switch (B). As long as th ...

  • Husqvarna K3600 MKII - page 7

    English – 7 SAFETY INSTR UCTIONS Chec king the blade guar d Chec k that the guard is complete and without any crac ks or def or mations. General saf ety precautions • A power cutter is designed to cut hard materials, such as masonr y . Obser ve the increased risk of kic kback when cutting soft materials. See instructions under the heading How t ...

  • Husqvarna K3600 MKII - page 8

    8 – English SAFETY INSTR UCTIONS Cutting General • Star t cutting with the machine running at maximum speed. • Alwa ys hold the machine in a fir m grip with both hands. Hold it so that the thumbs and fingers grip round the handles. Cutting technique The technique described below is of a general character . Check the details of each b lade c ...

  • Husqvarna K3600 MKII - page 9

    English – 9 SAFETY INSTR UCTIONS Large w ork Cuts e xceeding 1 m - secure a batten along the line to be cut. The batten acts as a guide. Use this guide to make a marking cut along the entire length of the cut, 50-70 mm (2-3 inches) in depth. Remov e the guides once the marking cut has been made. Small work First make a shallo w marking cut, max 5 ...

  • Husqvarna K3600 MKII - page 10

    10 – English SAFETY INSTR UCTIONS • Be aler t to mov ement of the work piece or anything else that can occur , which could cause the cut to close and pinch the blade . Pull in Pull in occurs when the disc’ s lower section suddenly stops or when the cut closes. (T o av oid, see the heading ”Basic rules” and ”Jamming/rotation”, here bel ...

  • Husqvarna K3600 MKII - page 11

    English – 11 SETTINGS AND ADJUSTMENTS Drive On account of the machine’ s unique design the dr iving power is not transf erred at the centre of the blade . The flanges on the two guide rollers run in the blade’ s groov es. Spr ings on the guide rollers press out the rollers, which in turn press the V - shaped edge on the inside diameter of th ...

  • Husqvarna K3600 MKII - page 12

    12 – English SETTINGS AND ADJUSTMENTS • Loosen the knob to offload the springs. • Pull out the lock f or the front handle and move the handle to the ser vice position. • Remov e the three screws holding the support roller guard using a 6 mm he x ke y and lift off the cov er . • Fit the blade . CA UTION! The blade has a groo ve (A) on one ...

  • Husqvarna K3600 MKII - page 13

    English – 13 SETTINGS AND ADJUSTMENTS CA UTION! The machine should be upright. If the machine lies on its side the weight of the b lade makes it difficult to make a correct adjustment. • Tighten the knobs fully and the machine is ready to use. Hydraulic hoses • Bef ore connecting the hoses: Ensure that the couplings are clean, both on the ma ...

  • Husqvarna K3600 MKII - page 14

    14 – English ST AR TING AND ST OPPING Star ting and stopping Starting • Grip the front handle with the left hand. • Grip the rear handle with the r ight hand. When you g rip the rear handle this releases the s witch lock. Stopping The machine is stopped by releasing the s witch. ! W ARNING! Note the following bef ore starting: Make sure you a ...

  • Husqvarna K3600 MKII - page 15

    English – 15 MAINTENANCE Maintenance Dismantling the complete guide r oller • Remov e the suppor t roller cov er . • Lift off the blade . • Unscrew the knob . First tur n the knob a fe w turns until you f eel a resistance. The guide roller then follows the knob out and stops when it f eels a resistance. The guide roller is pressed into the ...

  • Husqvarna K3600 MKII - page 16

    16 – English MAINTENANCE Drive wheel 1 Lock the axle using the loc king button. See the instructions under the heading What is what?. 2 Loosen the centre screw and remo ve the w asher . 3 Y ou can now lift off the drive wheel. CA UTION! Replace the dr ive wheel when fitting a ne w blade. A worn dr iv e wheel can result in the blade slipping and ...

  • Husqvarna K3600 MKII - page 17

    English – 17 MAINTENANCE Reconstructing the blade Couplings 1 W ater 2 W ater filter 3 Return 4 Pressure IMPOR T ANT! If the coupling is dir ty , the dir t can enter the oil and cause increased wear on the h ydraulic motor , hydr aulic pump , valv es, etc. It can also prev ent the coupling from sealing correctly . Alwa ys clean the couplings bef ...

  • Husqvarna K3600 MKII - page 18

    18 – English MAINTENANCE Maintenance schedule CA UTION! The char t is based on daily use of the equipment. Blades conforming to EN13236 Husqvarna K3600 MKII only conf or ms to 98/37/EC and EN13236 together with the blades listed belo w: Note: The blades are av ailable in diff erent hardnesses for diff erent mater ials, this is stated with two dig ...

  • Husqvarna K3600 MKII - page 19

    English – 19 TR OUBLE SHOO TING Mechanics Symptom Probab le cause The blade does not rotate . Roller knobs not tightened fully . The blade not fitted on guide rollers correctly . Rollers tensioned too much. P ossible f aulty hose connection to the hydr aulic system. P ossible f aulty hose connection to the drive source or other h ydraulic prob l ...

  • Husqvarna K3600 MKII - page 20

    20 – English TECHNICAL D A T A *W e recommend the use of environmentally appro ved h ydraulic oil. **With high ambient temperatures use oil with a higher viscosity . Note 1: Noise emissions in the environment measured as sound power (L W A ) in conf ormity with EC directive 2000/14/EC . Extending the hydraulic hoses When e xtending the hydr aulic ...

  • Husqvarna K3600 MKII - page 21

    English – 21 TECHNICAL D A T A EC-declaration of conf ormity Husqv arna Construction Pr oducts , SE-433 81 P ar tille, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter Husqv arna K3600 from 2006’ s serial numbers and onwards (the y ear is clearly stated in plain text on the rating plate with subsequent serial ...

  • Husqvarna K3600 MKII - page 22

    ´®z+R=J¶6G¨ ´®z+R=J¶6G¨ ...

  • Husqvarna K3600 MKII - page 23

    ...

  • Husqvarna K3600 MKII - page 24

    ´®z+R=J¶6G¨ 2006-12-15 ´®z+R=J¶6G¨ 1150294-26 ...

Produzent Husqvarna Kategorie Brush Cutter

Dokumente, die wir vom Produzenten des Geräts Husqvarna K3600 MKII erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Husqvarna
- Bedienungsanleitungen K3600 MKII
- Produktkarten Husqvarna
- Informationsbroschüren
- oder Energieetiketten Husqvarna K3600 MKII
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Husqvarna K3600 MKII.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Husqvarna K3600 MKII, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Husqvarna K3600 MKII. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Husqvarna K3600 MKII ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Husqvarna K3600 MKII, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Husqvarna K3600 MKII hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Husqvarna K3600 MKII verständlich ist.

Eine gänzliche Bedienungsanleitung von Husqvarna sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Husqvarna K3600 MKII bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Husqvarna K3600 MKII befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Husqvarna K3600 MKII, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Husqvarna K3600 MKII - die uns die ersten Schritte während der Nutzung von Husqvarna K3600 MKII erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Husqvarna K3600 MKII hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Husqvarna K3600 MKII im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Husqvarna K3600 MKII?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Husqvarna K3600 MKII nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Husqvarna K3600 MKII hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)