-
Husqvarna K3600 MKII - page 1
E E E E n n n n g g g g l l l l i i i i s s s s h h h h K3600 MKII Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine. ...
-
Husqvarna K3600 MKII - page 2
2 – English KEY T O SYMBOLS K ey to symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ed pr ...
-
Husqvarna K3600 MKII - page 3
English – 3 CONTENTS Contents KEY T O SYMBOLS K ey to symbols ............................................................. 2 CONTENTS Contents ...................................................................... 3 WHA T IS WHA T? What is what on the po wer cutter? ............................... 4 SAFETY INSTR UCTIONS Steps bef ore using a new ...
-
Husqvarna K3600 MKII - page 4
4 – English WHA T IS WHA T? What is what on the po wer cutter? 1 Diamond blade 2 Blade guard/spra y guard 3 Hydraulic motor 4 Locking b utton f or the drive wheel 5 Grease nipples 6 Control f or the guide rollers 7 F ront handle (adjustable) 8 W ater adjustment control 9 Switch 10 W ater connector 11 Couplings f or hydr aulic hoses 12 Rating plat ...
-
Husqvarna K3600 MKII - page 5
English – 5 SAFETY INSTR UCTIONS Steps bef ore using a new po wer cutter . • This machine is a h ydraulically operated po wer cutter intended f or free-hand cutting. The machine should be connected to a h ydraulic unit with an oil flow of 35-42 litres/min and a maximum pressure of 150 bar . • Please read the operator’ s manual carefully . ...
-
Husqvarna K3600 MKII - page 6
6 – English SAFETY INSTR UCTIONS Switc h lock and ON/OFF v alve for the water The s witch lock is designed to pre vent accidental operation of the s witch. The ON/OFF valv e for the water supply is also controlled with the s witch lock. When the s witch lock (A) is pressed in this opens the w ater valv e and releases the switch (B). As long as th ...
-
Husqvarna K3600 MKII - page 7
English – 7 SAFETY INSTR UCTIONS Chec king the blade guar d Chec k that the guard is complete and without any crac ks or def or mations. General saf ety precautions • A power cutter is designed to cut hard materials, such as masonr y . Obser ve the increased risk of kic kback when cutting soft materials. See instructions under the heading How t ...
-
Husqvarna K3600 MKII - page 8
8 – English SAFETY INSTR UCTIONS Cutting General • Star t cutting with the machine running at maximum speed. • Alwa ys hold the machine in a fir m grip with both hands. Hold it so that the thumbs and fingers grip round the handles. Cutting technique The technique described below is of a general character . Check the details of each b lade c ...
-
Husqvarna K3600 MKII - page 9
English – 9 SAFETY INSTR UCTIONS Large w ork Cuts e xceeding 1 m - secure a batten along the line to be cut. The batten acts as a guide. Use this guide to make a marking cut along the entire length of the cut, 50-70 mm (2-3 inches) in depth. Remov e the guides once the marking cut has been made. Small work First make a shallo w marking cut, max 5 ...
-
Husqvarna K3600 MKII - page 10
10 – English SAFETY INSTR UCTIONS • Be aler t to mov ement of the work piece or anything else that can occur , which could cause the cut to close and pinch the blade . Pull in Pull in occurs when the disc’ s lower section suddenly stops or when the cut closes. (T o av oid, see the heading ”Basic rules” and ”Jamming/rotation”, here bel ...
-
Husqvarna K3600 MKII - page 11
English – 11 SETTINGS AND ADJUSTMENTS Drive On account of the machine’ s unique design the dr iving power is not transf erred at the centre of the blade . The flanges on the two guide rollers run in the blade’ s groov es. Spr ings on the guide rollers press out the rollers, which in turn press the V - shaped edge on the inside diameter of th ...
-
Husqvarna K3600 MKII - page 12
12 – English SETTINGS AND ADJUSTMENTS • Loosen the knob to offload the springs. • Pull out the lock f or the front handle and move the handle to the ser vice position. • Remov e the three screws holding the support roller guard using a 6 mm he x ke y and lift off the cov er . • Fit the blade . CA UTION! The blade has a groo ve (A) on one ...
-
Husqvarna K3600 MKII - page 13
English – 13 SETTINGS AND ADJUSTMENTS CA UTION! The machine should be upright. If the machine lies on its side the weight of the b lade makes it difficult to make a correct adjustment. • Tighten the knobs fully and the machine is ready to use. Hydraulic hoses • Bef ore connecting the hoses: Ensure that the couplings are clean, both on the ma ...
-
Husqvarna K3600 MKII - page 14
14 – English ST AR TING AND ST OPPING Star ting and stopping Starting • Grip the front handle with the left hand. • Grip the rear handle with the r ight hand. When you g rip the rear handle this releases the s witch lock. Stopping The machine is stopped by releasing the s witch. ! W ARNING! Note the following bef ore starting: Make sure you a ...
-
Husqvarna K3600 MKII - page 15
English – 15 MAINTENANCE Maintenance Dismantling the complete guide r oller • Remov e the suppor t roller cov er . • Lift off the blade . • Unscrew the knob . First tur n the knob a fe w turns until you f eel a resistance. The guide roller then follows the knob out and stops when it f eels a resistance. The guide roller is pressed into the ...
-
Husqvarna K3600 MKII - page 16
16 – English MAINTENANCE Drive wheel 1 Lock the axle using the loc king button. See the instructions under the heading What is what?. 2 Loosen the centre screw and remo ve the w asher . 3 Y ou can now lift off the drive wheel. CA UTION! Replace the dr ive wheel when fitting a ne w blade. A worn dr iv e wheel can result in the blade slipping and ...
-
Husqvarna K3600 MKII - page 17
English – 17 MAINTENANCE Reconstructing the blade Couplings 1 W ater 2 W ater filter 3 Return 4 Pressure IMPOR T ANT! If the coupling is dir ty , the dir t can enter the oil and cause increased wear on the h ydraulic motor , hydr aulic pump , valv es, etc. It can also prev ent the coupling from sealing correctly . Alwa ys clean the couplings bef ...
-
Husqvarna K3600 MKII - page 18
18 – English MAINTENANCE Maintenance schedule CA UTION! The char t is based on daily use of the equipment. Blades conforming to EN13236 Husqvarna K3600 MKII only conf or ms to 98/37/EC and EN13236 together with the blades listed belo w: Note: The blades are av ailable in diff erent hardnesses for diff erent mater ials, this is stated with two dig ...
-
Husqvarna K3600 MKII - page 19
English – 19 TR OUBLE SHOO TING Mechanics Symptom Probab le cause The blade does not rotate . Roller knobs not tightened fully . The blade not fitted on guide rollers correctly . Rollers tensioned too much. P ossible f aulty hose connection to the hydr aulic system. P ossible f aulty hose connection to the drive source or other h ydraulic prob l ...
-
Husqvarna K3600 MKII - page 20
20 – English TECHNICAL D A T A *W e recommend the use of environmentally appro ved h ydraulic oil. **With high ambient temperatures use oil with a higher viscosity . Note 1: Noise emissions in the environment measured as sound power (L W A ) in conf ormity with EC directive 2000/14/EC . Extending the hydraulic hoses When e xtending the hydr aulic ...
-
Husqvarna K3600 MKII - page 21
English – 21 TECHNICAL D A T A EC-declaration of conf ormity Husqv arna Construction Pr oducts , SE-433 81 P ar tille, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter Husqv arna K3600 from 2006’ s serial numbers and onwards (the y ear is clearly stated in plain text on the rating plate with subsequent serial ...
-
Husqvarna K3600 MKII - page 22
´®z+R=J¶6G¨ ´®z+R=J¶6G¨ ...
-
Husqvarna K3600 MKII - page 23
...
-
Husqvarna K3600 MKII - page 24
´®z+R=J¶6G¨ 2006-12-15 ´®z+R=J¶6G¨ 1150294-26 ...
У вас вопрос, касающийся Husqvarna K3600 MKII?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Husqvarna K3600 MKII, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Husqvarna K3600 MKII со всей вероятностью он захочет поделиться методом ее решения.