Bedienungsanleitung Smeg PGF75SC3

16 Seiten Betrifft nicht
Download

Zur Seite of 16

Summary
  • Smeg PGF75SC3 - page 1

    Summary 1 INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 20 2 POSITIONING OF THE HOB _______________________________ 22 3 ADJUSTMENT TO DIFFERENT TYPES OF GAS _______________ 28 4 FINAL OPERATIONS _____________________________________ 30 5 USING THE HOB ________________________________________ 31 6 CLEANING AND MAINTENANCE ___________________ ...

  • Smeg PGF75SC3 - page 2

    Introduction 1 INSTR UCTIONS FOR SAFE AND PR OPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS EN TIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. INSTALLATI ...

  • Smeg PGF75SC3 - page 3

    Introduction THE APPLIANCE DATA PLATE, WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME, IS POSITIONED AT A VISIBLE POINT UNDER THE SAFETY COVER. THE DATA PLATE ON THE PROTECTIVE COVER MUST NEVER BE REMOVED . DO NOT PUT PANS WITHOUT PERFECTLY PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE HOB PANSTAND GRIDS. DO NOT USE COOKING RECEPTACLES THAT EXT ...

  • Smeg PGF75SC3 - page 4

    Instructions for the installer 22 2 POSITIONING OF THE HOB The following operation requires buildi ng and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminat ed wood, as long as they are heat- resistant (T 90°C). 2.1 Attachment ...

  • Smeg PGF75SC3 - page 5

    Instructions for the installer 2.2 Attachment to support structure, flush-mounting model Create an opening with the dimensions shown in the figure in the work surface, observing a minimum distance of 50 mm from the rear edge. 1) The lower part of the protective cover must be fully accessible when the appliance is installed. This appliance can be in ...

  • Smeg PGF75SC3 - page 6

    Instructions for the installer 24 Important: Other types of installation will only be possible under th e manufacturer's supervision. Overall dimensions: location of gas and electrical connection points (all measures in mm). Warning: the bottom surface of the hob can become very hot. To avoid a hazard, under-bench access must be restricted. Re ...

  • Smeg PGF75SC3 - page 7

    Instructions for the installer 2.3 Electrical connection Make sure that the voltage and capacit y of the power supply cable conform to the data shown on the plate loca ted under the protective cover. Do not remove this plat e for any reason . The power supply cable plug and the wa ll socket must be of the same type and conform to the current electr ...

  • Smeg PGF75SC3 - page 8

    Instructions for the installer 26 2.4 Ventilation requirements The appliance may be installed only in rooms with permanent ventilation, as required by standards regolations in force. The room in which the appliance is installed must have sufficient air flow to satisfy the requirements of normal gas combus tion and of necessary air exchange in the r ...

  • Smeg PGF75SC3 - page 9

    Instructions for the installer 2.6 Gas connection Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe conforming to the prov isions defined by standard regolations in force. After connection operations, check for leaks using a soapy solution. The hob has been inspected for G20 natural gas (2H) at a pressure of 2 ...

  • Smeg PGF75SC3 - page 10

    Instructions for the installer 28 3 ADJUSTMENT T O DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, unplug th e appliance from the mains. The hob is set for natural gas G20 (2H) at a pressure of 20 mbar. In the case of functioning with other types of gas the burner nozzles must be changed and the minimum flame adjust ed on ...

  • Smeg PGF75SC3 - page 11

    Instructions for the installer 3.2 Burner and nozzle characteristics table Burner Rated heating capacity (kW) LPG – G30/G31 30/37 mbar Nozzle diameter 1/100 mm By-pass mm 1/100 Reduced flow rate (W) Flow rate g/h G30 Flow rate g/h G31 Auxiliary (1) 1.05 50 30 * 27/28 ** 400 76 75 Semi rapid (2) 1.75 63 30 * 32/33 ** 500 127 125 Ultra Rapid (3) 4. ...

  • Smeg PGF75SC3 - page 12

    Instructions for the installer 30 4 FINAL OPERA TIONS After carrying out the above adjustments, remount in reverse order to the instructions given in paragraph “3.1 Replacement of nozzles on the hob”. After having regulated the device wit h gas other than the one tested, replace the label located on the guar d with the one that corresponds to t ...

  • Smeg PGF75SC3 - page 13

    Instructions for the user 5 USING THE HOB 5.1 Ignition of the burners Before turning on the burners, make su re that the flame-spreader crowns and respective caps are properly fi tted in their housings. Ensure the flame-spreader holes A are aligned with the ignition plugs and the thermocouples. Panstand grid B , available upon request, is intended ...

  • Smeg PGF75SC3 - page 14

    Instructions for the user 32 5.2 Practical advice for using the burners For better use of the burners and lowe r gas consumption, use covered cooking receptacles that have a flat, smooth bottom and are proportional in size to the burner to prevent the flame from licking the sides (see paragraph “ 5.3 Diameter of receptacles ”). When water reach ...

  • Smeg PGF75SC3 - page 15

    Instructions for the user 6 CLEANING AND MAINTENANCE Before any intervention, disconnect the appliance from the mains. Never use a steam jet to clean the appliance. 6.1 Cleaning the stainless steel To keep stainless steel in good c ondition it should be cleaned regularly after use. Let it cool first. 6.1.1 Routine daily cleaning To clean and preser ...

  • Smeg PGF75SC3 - page 16

    Instructions for the user 34 In models with central pan stand, fit this piece, taking care that its centre is perfectly aligned with the centre of the burner ...

Produzent Smeg Kategorie Stove

Dokumente, die wir vom Produzenten des Geräts Smeg PGF75SC3 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Smeg
- Bedienungsanleitungen PGF75SC3
- Produktkarten Smeg
- Informationsbroschüren
- oder Energieetiketten Smeg PGF75SC3
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Smeg PGF75SC3.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Smeg PGF75SC3, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Smeg PGF75SC3. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Smeg PGF75SC3 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Smeg PGF75SC3, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Smeg PGF75SC3 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Smeg PGF75SC3 verständlich ist.

Eine gänzliche Bedienungsanleitung von Smeg sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Smeg PGF75SC3 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Smeg PGF75SC3 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Smeg PGF75SC3, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Smeg PGF75SC3 - die uns die ersten Schritte während der Nutzung von Smeg PGF75SC3 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Smeg PGF75SC3 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Smeg PGF75SC3 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Smeg PGF75SC3?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Smeg PGF75SC3 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Smeg PGF75SC3 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)