Bedienungsanleitung Patton electronic 1082, 144, I

28 Seiten 0.55 mb
Download

Zur Seite of 28

Summary
  • Patton electronic 1082, 144, I - page 1

    USER MANUAL MODEL 1082/I and 1082/144/I iDSL Modem with 10Base- T Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P art# 07M1082I-UM Doc# 03318U2-001 Rev . C Revised 10/27/06 An ISO-9001 Certified Company CERTIFIED ...

  • Patton electronic 1082, 144, I - page 2

    2 T ABLE OF CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 FCC Information ........................................................................... 4 1.2 CE Notice ...................................................................................... 4 1.3 Service ....................... ...

  • Patton electronic 1082, 144, I - page 3

    3 A.8 Connectors ................................................................................. 25 A.9 Power .......................................................................................... 25 A.10 Temperature Range .................................................................... 26 A.11 Altitude ................................... ...

  • Patton electronic 1082, 144, I - page 4

    4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 1082/I and Model 1082/144/I components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment. This warranty is limited to def ects in w orkmanship or mater ials, and does not cov er custome ...

  • Patton electronic 1082, 144, I - page 5

    5 1.3 SERVICE All warranty and non-w arranty repairs must be returned freight prepaid and insured to P atton Electronics. All retur ns must ha ve a Return Mater i- als A uthorization number on the outside of the shipping container . This number ma y be obtained from Patton Electronics T echnical Ser vice at: T el: (301) 975-1007 E-mail: support@pat ...

  • Patton electronic 1082, 144, I - page 6

    6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear par ts and labor . If any questions or prob lems ar ise during installation or use of this product, please do not hesitate to contact P atton Electronics T echnical Support ...

  • Patton electronic 1082, 144, I - page 7

    7 2.2 DESCRIPTION The Model 1082/I and Model 1082/144/I are Multi Rate iDSL Modems that provide seamless MA C La yer connectivity between 2 peered 10Base-T LANs. Now , Enter prise users no longer need to hassle with a bridge and a CSU/DSU or recurring leased line costs. The 1082 allo ws users to add addi- tional nodes to a LAN that has reached its ...

  • Patton electronic 1082, 144, I - page 8

    8 3.0 PPP OPERATIONAL BACKGR OUND PPP is a protocol used f or multi-ple xed transport over a point-to-point link. PPP operates on all full duple x media, and is a symmetr ic peer-to- peer protocol, which can be broken into three main components: • A standard method to encapsulate datagrams o ver serial links • A Link Control Protocol (LCP) to e ...

  • Patton electronic 1082, 144, I - page 9

    9 Figure 2. Cisco router with serial interface, configured as PPP Half-Bridge Figure 2 shows a typical Cisco router with a serial interf ace configured as a PPP Half Bridge. The router serial interface uses a remote de vice that suppor ts PPP bridging to function as a node on the remote Ether net network. The ser ial interf ace on the Cisco will ...

  • Patton electronic 1082, 144, I - page 10

    10 Figure 3. T ransparent bridging between two routers ov er a ser ial interface Figure 3 illustrates transparent bridging between two routers o ver a serial interface (s0). Br idging will occur between the two Ethernet inter- f aces on router A (e0 and e1) and the two Ethernet interfaces on router B (e0 and e1). ...

  • Patton electronic 1082, 144, I - page 11

    11 4.0 CONFIGURATION The Model 1082/I and Model 1082/144/I each are equipped with 16 DIP s witches that enable configur ation of the unit f or a wide v ariety of appli- cations. This section describes switch locations and e xplains the different configurations. 4.1 CONFIGURING THE HAR DWARE DIP SWITCHES Using a small flat-tip screwdriv er , remo ...

  • Patton electronic 1082, 144, I - page 12

    12 Figure 5. DIP switches S2 and S2 Figure 5 shows the orientation of the DIP s witches in the “ON” and “OFF” positions. Configuring DIP Switch S1 DIP s witch S1 is where you configure the data r ate, asynchronous or synchronous data f ormat, transmit clock source, and response to RDL request. The follo wing table summarizes default posit ...

  • Patton electronic 1082, 144, I - page 13

    13 Note When setting the 1082 for SNMP Management, the DTE r ate switches (S1-1,S1-2, and S2-1) m ust be also set to the ON posi- tion. Theref ore, to set a 1082 unit SNMP Mangagement mode, the follo wing s witches hav e to be at the ON position, S1-1, S1-2, S2-1. Switches S1-1 and S1-2: Data Rate Use s witches S1-1 and S1-2 to configure the async ...

  • Patton electronic 1082, 144, I - page 14

    14 Switches S1-6 and S1-7: System Clock Mode Use Switches S1-6 and S1-7 to configure the 1082/I or Model 1082/144/ I f or internal, or receive recov er clock mode. Switch S1-8: Response to RDL Request Use Switch S1-8 to allow Model 1082/I and Model 1082/144/I to enter the Remote Digital Loopback diagnostic test when requested to do so b y the f ar ...

  • Patton electronic 1082, 144, I - page 15

    15 Configuring DIP switch “S2” Use the eight DIP s witches in S2 to enable 19.2 kbps or 144* kbps syn- chronous operation and set the loopbac k modes. The f ollowing tab le summarizes def ault positions of DIP s witches S2-1 through S2-8. Detailed descriptions of each switch f ollow the table . Switches S2-1: 19.2 kbps or 144 * kbps Synchr ono ...

  • Patton electronic 1082, 144, I - page 16

    16 Switch S2-2: Front P anel Switch Disable Use s witch S2-2 to enable or disab le the front panel toggle switches. Switches S2-3, S2-6, S2-7 and S2-8: Reser ved S2-2 Setting On Disable the front panel s witches Off Enable the front panel s witches ...

  • Patton electronic 1082, 144, I - page 17

    17 5.0 INSTALLATION When the Model 1082 has been properly configured, it may be con- nected to the DSL twisted pair interf ace, the 10Base-T Ethernet Inter- f ace, and the po wer source. This section descr ibes these connections. Figure 6. Model 1082/I or Model 1082/144/I rear view 5.1 CONNECTING DSL INTERFACE The Model 1082 suppor ts communicatio ...

  • Patton electronic 1082, 144, I - page 18

    18 The RJ-45 connector on the Model 1082’ s twisted pair interface is polar- ity insensitive and is wired f or a two-wire interf ace. The signal/pin rela- tionships are shown in Figure 7 belo w . Figure 7. Model 1082/I twisted pair line interface 5.2 CONNECTING 10BASE-T ETHERNET PORT TO PC (DTE) The 10Base-T interf ace is configured as DTE (Data ...

  • Patton electronic 1082, 144, I - page 19

    19 5.4 POWER CONNECTION Universal A C P ower (100–240V AC) The Model 1082/I uses a 5VDC , 2A universal input 100–240V AC , power supply (center pin is +5V). The universal input po wer supply has a male IEC-320 power entry connector . This power supply connects to the Model 1082/I by means of a barrel jac k on the rear panel. Many inter na- tion ...

  • Patton electronic 1082, 144, I - page 20

    20 DC P ower The 36-60 VDC DC to DC adapter is supplied with the DC version of the Model 1082. The blac k and red leads plug into a DC source (nominal 48VDC) and the barrel power connector plugs into the barrel po wer sup- ply jack on the rear panel of the 1082. (See Figure 10). Figure 10. P ower adapter W ARNING There are no user -ser viceable par ...

  • Patton electronic 1082, 144, I - page 21

    21 6.0 OPERATION When the Model 1082/I and Model 1082/144/I hav e been properly config- ured and installed, it should operate transparently . This sections describes power-up , LED status monitors, and the b uilt-in loopbac k test modes . 6.1 POWER-UP Bef ore applying power to the Model 1082/I or Model 1082/144/I, please read section 5.4, “P owe ...

  • Patton electronic 1082, 144, I - page 22

    22 T able 1: LED status monitor indications LED Description DSL Link (Activ e Green) Solid green (On) indicates that the end to end DSL F ramer Link is up, signifying that the link across the DSL span is active . The DSL Link LED is Off when the link is down. Status Blinks yello w from one to ele v en times to indicate system status. Each pulse pat ...

  • Patton electronic 1082, 144, I - page 23

    23 6.3 T EST MODES The Model 1082/I and Model 1082/144/I has a built-in proprietary loop- back test mode , plus a b uilt-in V .52 BER test patter n generator , for e valu- ating the condition of the modems and the communication link. These tests can be activated ph ysically from the front panel, or via the interf ace . Remote Digital Loopback (RDL) ...

  • Patton electronic 1082, 144, I - page 24

    24 Activating RDL can be done in tw o ways: 1. Mov e the front panel toggle switch to appropriate position. 2. Set remote loopback from SNMP screen (when used with 1092ARC Rack Card) Note Remote loopback cannot be activ ated until approximately 45 seconds after the two modems hav e linked to each other . Note The Remote Digital Loopback (RDL) will ...

  • Patton electronic 1082, 144, I - page 25

    25 APPENDIX A 1082/I Specifications A.1 T RANSMISSION FORMAT Synchronous or asynchronous A.2 T RANSMISSION LINE Single unconditioned twisted pair A.3 CLOCKING Internal or receive loopback A.4 DISTANCE A.5 DATA RATES Synchronous 19.2, 32, 56, 64, and 128 kbps, (and 144 kbps on 1082/144 only); Asynchronous 0–38.4 kbps A.6 DIAGNOSTICS V .52 complia ...

  • Patton electronic 1082, 144, I - page 26

    26 A.10 T EMPERATURE RANGE 32–122°F (0–50°C) A.11 ALTITUDE 0–15,000 f eet (0–4,572 meters) A.12 HUMIDITY 5–95% non-condensing A.13 DIMENSIONS 4.125W x 1.625H x 6.0D in. (10.5W x 4.1W x 15.2D cm) A.14 WEIGHT 2.01 lbs. (1.0 kg) ...

  • Patton electronic 1082, 144, I - page 27

    27 APPENDIX B MODEL 1082/I F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES Model # Description 1082/I 10Base-T , DSL Modem 1082/144/I 10Base-T DSL modem with maximum data rate of 144 kbps 48V -PSM DC P ower Supply Module 08055DCUI 100-240V AC (+5V ±5% reg. DC/2A) Universal Input Adapter 0805EUR European P ow er Cord CEE 7 (“A”) 0805UK United Ki ...

  • Patton electronic 1082, 144, I - page 28

    28 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ ___________________________________________________ ...

Produzent Patton electronic Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts Patton electronic 1082, 144, I erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Patton electronic
- Bedienungsanleitungen 1082, 144, I
- Produktkarten Patton electronic
- Informationsbroschüren
- oder Energieetiketten Patton electronic 1082, 144, I
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Patton electronic 1082, 144, I.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Patton electronic 1082, 144, I, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Patton electronic 1082, 144, I. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Patton electronic 1082, 144, I ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Patton electronic 1082, 144, I, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Patton electronic 1082, 144, I hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Patton electronic 1082, 144, I verständlich ist.

Eine gänzliche Bedienungsanleitung von Patton electronic sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Patton electronic 1082, 144, I bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Patton electronic 1082, 144, I befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Patton electronic 1082, 144, I, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Patton electronic 1082, 144, I - die uns die ersten Schritte während der Nutzung von Patton electronic 1082, 144, I erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Patton electronic 1082, 144, I hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Patton electronic 1082, 144, I im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Patton electronic 1082, 144, I?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Patton electronic 1082, 144, I nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Patton electronic 1082, 144, I hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)