Español dropdown-ico

Manual de instrucciones Patton electronic 1082, 144, I

28 de páginas 0.55 mb
Descargar

Pasar a la página of 28

Summary
  • Patton electronic 1082, 144, I - page 1

    USER MANUAL MODEL 1082/I and 1082/144/I iDSL Modem with 10Base- T Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P art# 07M1082I-UM Doc# 03318U2-001 Rev . C Revised 10/27/06 An ISO-9001 Certified Company CERTIFIED ...

  • Patton electronic 1082, 144, I - page 2

    2 T ABLE OF CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 FCC Information ........................................................................... 4 1.2 CE Notice ...................................................................................... 4 1.3 Service ....................... ...

  • Patton electronic 1082, 144, I - page 3

    3 A.8 Connectors ................................................................................. 25 A.9 Power .......................................................................................... 25 A.10 Temperature Range .................................................................... 26 A.11 Altitude ................................... ...

  • Patton electronic 1082, 144, I - page 4

    4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 1082/I and Model 1082/144/I components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment. This warranty is limited to def ects in w orkmanship or mater ials, and does not cov er custome ...

  • Patton electronic 1082, 144, I - page 5

    5 1.3 SERVICE All warranty and non-w arranty repairs must be returned freight prepaid and insured to P atton Electronics. All retur ns must ha ve a Return Mater i- als A uthorization number on the outside of the shipping container . This number ma y be obtained from Patton Electronics T echnical Ser vice at: T el: (301) 975-1007 E-mail: support@pat ...

  • Patton electronic 1082, 144, I - page 6

    6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear par ts and labor . If any questions or prob lems ar ise during installation or use of this product, please do not hesitate to contact P atton Electronics T echnical Support ...

  • Patton electronic 1082, 144, I - page 7

    7 2.2 DESCRIPTION The Model 1082/I and Model 1082/144/I are Multi Rate iDSL Modems that provide seamless MA C La yer connectivity between 2 peered 10Base-T LANs. Now , Enter prise users no longer need to hassle with a bridge and a CSU/DSU or recurring leased line costs. The 1082 allo ws users to add addi- tional nodes to a LAN that has reached its ...

  • Patton electronic 1082, 144, I - page 8

    8 3.0 PPP OPERATIONAL BACKGR OUND PPP is a protocol used f or multi-ple xed transport over a point-to-point link. PPP operates on all full duple x media, and is a symmetr ic peer-to- peer protocol, which can be broken into three main components: • A standard method to encapsulate datagrams o ver serial links • A Link Control Protocol (LCP) to e ...

  • Patton electronic 1082, 144, I - page 9

    9 Figure 2. Cisco router with serial interface, configured as PPP Half-Bridge Figure 2 shows a typical Cisco router with a serial interf ace configured as a PPP Half Bridge. The router serial interface uses a remote de vice that suppor ts PPP bridging to function as a node on the remote Ether net network. The ser ial interf ace on the Cisco will ...

  • Patton electronic 1082, 144, I - page 10

    10 Figure 3. T ransparent bridging between two routers ov er a ser ial interface Figure 3 illustrates transparent bridging between two routers o ver a serial interface (s0). Br idging will occur between the two Ethernet inter- f aces on router A (e0 and e1) and the two Ethernet interfaces on router B (e0 and e1). ...

  • Patton electronic 1082, 144, I - page 11

    11 4.0 CONFIGURATION The Model 1082/I and Model 1082/144/I each are equipped with 16 DIP s witches that enable configur ation of the unit f or a wide v ariety of appli- cations. This section describes switch locations and e xplains the different configurations. 4.1 CONFIGURING THE HAR DWARE DIP SWITCHES Using a small flat-tip screwdriv er , remo ...

  • Patton electronic 1082, 144, I - page 12

    12 Figure 5. DIP switches S2 and S2 Figure 5 shows the orientation of the DIP s witches in the “ON” and “OFF” positions. Configuring DIP Switch S1 DIP s witch S1 is where you configure the data r ate, asynchronous or synchronous data f ormat, transmit clock source, and response to RDL request. The follo wing table summarizes default posit ...

  • Patton electronic 1082, 144, I - page 13

    13 Note When setting the 1082 for SNMP Management, the DTE r ate switches (S1-1,S1-2, and S2-1) m ust be also set to the ON posi- tion. Theref ore, to set a 1082 unit SNMP Mangagement mode, the follo wing s witches hav e to be at the ON position, S1-1, S1-2, S2-1. Switches S1-1 and S1-2: Data Rate Use s witches S1-1 and S1-2 to configure the async ...

  • Patton electronic 1082, 144, I - page 14

    14 Switches S1-6 and S1-7: System Clock Mode Use Switches S1-6 and S1-7 to configure the 1082/I or Model 1082/144/ I f or internal, or receive recov er clock mode. Switch S1-8: Response to RDL Request Use Switch S1-8 to allow Model 1082/I and Model 1082/144/I to enter the Remote Digital Loopback diagnostic test when requested to do so b y the f ar ...

  • Patton electronic 1082, 144, I - page 15

    15 Configuring DIP switch “S2” Use the eight DIP s witches in S2 to enable 19.2 kbps or 144* kbps syn- chronous operation and set the loopbac k modes. The f ollowing tab le summarizes def ault positions of DIP s witches S2-1 through S2-8. Detailed descriptions of each switch f ollow the table . Switches S2-1: 19.2 kbps or 144 * kbps Synchr ono ...

  • Patton electronic 1082, 144, I - page 16

    16 Switch S2-2: Front P anel Switch Disable Use s witch S2-2 to enable or disab le the front panel toggle switches. Switches S2-3, S2-6, S2-7 and S2-8: Reser ved S2-2 Setting On Disable the front panel s witches Off Enable the front panel s witches ...

  • Patton electronic 1082, 144, I - page 17

    17 5.0 INSTALLATION When the Model 1082 has been properly configured, it may be con- nected to the DSL twisted pair interf ace, the 10Base-T Ethernet Inter- f ace, and the po wer source. This section descr ibes these connections. Figure 6. Model 1082/I or Model 1082/144/I rear view 5.1 CONNECTING DSL INTERFACE The Model 1082 suppor ts communicatio ...

  • Patton electronic 1082, 144, I - page 18

    18 The RJ-45 connector on the Model 1082’ s twisted pair interface is polar- ity insensitive and is wired f or a two-wire interf ace. The signal/pin rela- tionships are shown in Figure 7 belo w . Figure 7. Model 1082/I twisted pair line interface 5.2 CONNECTING 10BASE-T ETHERNET PORT TO PC (DTE) The 10Base-T interf ace is configured as DTE (Data ...

  • Patton electronic 1082, 144, I - page 19

    19 5.4 POWER CONNECTION Universal A C P ower (100–240V AC) The Model 1082/I uses a 5VDC , 2A universal input 100–240V AC , power supply (center pin is +5V). The universal input po wer supply has a male IEC-320 power entry connector . This power supply connects to the Model 1082/I by means of a barrel jac k on the rear panel. Many inter na- tion ...

  • Patton electronic 1082, 144, I - page 20

    20 DC P ower The 36-60 VDC DC to DC adapter is supplied with the DC version of the Model 1082. The blac k and red leads plug into a DC source (nominal 48VDC) and the barrel power connector plugs into the barrel po wer sup- ply jack on the rear panel of the 1082. (See Figure 10). Figure 10. P ower adapter W ARNING There are no user -ser viceable par ...

  • Patton electronic 1082, 144, I - page 21

    21 6.0 OPERATION When the Model 1082/I and Model 1082/144/I hav e been properly config- ured and installed, it should operate transparently . This sections describes power-up , LED status monitors, and the b uilt-in loopbac k test modes . 6.1 POWER-UP Bef ore applying power to the Model 1082/I or Model 1082/144/I, please read section 5.4, “P owe ...

  • Patton electronic 1082, 144, I - page 22

    22 T able 1: LED status monitor indications LED Description DSL Link (Activ e Green) Solid green (On) indicates that the end to end DSL F ramer Link is up, signifying that the link across the DSL span is active . The DSL Link LED is Off when the link is down. Status Blinks yello w from one to ele v en times to indicate system status. Each pulse pat ...

  • Patton electronic 1082, 144, I - page 23

    23 6.3 T EST MODES The Model 1082/I and Model 1082/144/I has a built-in proprietary loop- back test mode , plus a b uilt-in V .52 BER test patter n generator , for e valu- ating the condition of the modems and the communication link. These tests can be activated ph ysically from the front panel, or via the interf ace . Remote Digital Loopback (RDL) ...

  • Patton electronic 1082, 144, I - page 24

    24 Activating RDL can be done in tw o ways: 1. Mov e the front panel toggle switch to appropriate position. 2. Set remote loopback from SNMP screen (when used with 1092ARC Rack Card) Note Remote loopback cannot be activ ated until approximately 45 seconds after the two modems hav e linked to each other . Note The Remote Digital Loopback (RDL) will ...

  • Patton electronic 1082, 144, I - page 25

    25 APPENDIX A 1082/I Specifications A.1 T RANSMISSION FORMAT Synchronous or asynchronous A.2 T RANSMISSION LINE Single unconditioned twisted pair A.3 CLOCKING Internal or receive loopback A.4 DISTANCE A.5 DATA RATES Synchronous 19.2, 32, 56, 64, and 128 kbps, (and 144 kbps on 1082/144 only); Asynchronous 0–38.4 kbps A.6 DIAGNOSTICS V .52 complia ...

  • Patton electronic 1082, 144, I - page 26

    26 A.10 T EMPERATURE RANGE 32–122°F (0–50°C) A.11 ALTITUDE 0–15,000 f eet (0–4,572 meters) A.12 HUMIDITY 5–95% non-condensing A.13 DIMENSIONS 4.125W x 1.625H x 6.0D in. (10.5W x 4.1W x 15.2D cm) A.14 WEIGHT 2.01 lbs. (1.0 kg) ...

  • Patton electronic 1082, 144, I - page 27

    27 APPENDIX B MODEL 1082/I F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES Model # Description 1082/I 10Base-T , DSL Modem 1082/144/I 10Base-T DSL modem with maximum data rate of 144 kbps 48V -PSM DC P ower Supply Module 08055DCUI 100-240V AC (+5V ±5% reg. DC/2A) Universal Input Adapter 0805EUR European P ow er Cord CEE 7 (“A”) 0805UK United Ki ...

  • Patton electronic 1082, 144, I - page 28

    28 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ ___________________________________________________ ...

Fabricante Patton electronic Categoría Network Card

Los documentos del dispositivo Patton electronic 1082, 144, I que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Patton electronic
- manuales de instrucciones 1082, 144, I
- hojas de producto Patton electronic
- folletos informativos
- o etiquetas energéticas Patton electronic 1082, 144, I
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Patton electronic 1082, 144, I.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Patton electronic 1082, 144, I, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Patton electronic 1082, 144, I. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Patton electronic 1082, 144, I.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Patton electronic 1082, 144, I, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Patton electronic 1082, 144, I. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Patton electronic 1082, 144, I.

El manual de instrucciones completo de Patton electronic debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Patton electronic 1082, 144, I - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Patton electronic 1082, 144, I, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Patton electronic 1082, 144, I que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Patton electronic 1082, 144, I - que deben facilitarnos los primeros pasos durante el uso de Patton electronic 1082, 144, I
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Patton electronic 1082, 144, I
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Patton electronic 1082, 144, I en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Patton electronic 1082, 144, I?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Patton electronic 1082, 144, I, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Patton electronic 1082, 144, I probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)