Manual de instrucciones Field Controls PVU-300

16 de páginas 0.87 mb
Descargar

Pasar a la página of 16

Summary
  • Field Controls PVU-300 - page 1

    2630 Airport Road · Kinston, NC 28504 Phone: 252-522-3031· Fax: 252-522 -0214 www.fieldcontrols.com POWER VENTER SYSTEM Mode l: PVU-300 Included is one ETL LISTED po wer venter to be used fo r side wall venting of a single 120/24 VAC controlled furnace, boiler, or water heater which burns natural or LP gas, or oil. The PVU may also be used to ven ...

  • Field Controls PVU-300 - page 2

    Page 2 UNIT SPECIFICATIONS (See Table 1 and Figure 1 ) Table 1 UNIT DIMENSIONS (INCHES) MODEL “H” “W” “D” I/O* PVU-300 7.5 11.5 7.0 4/4 * Inlet and outlet diameter. ELECTRICAL RATINGS MODEL VAC Hz RPM WATT AM P TP** PVU-300 115 60 3000 145 2.1 YES ** Thermally protected motor. SIDEWALL VENT HOODS (Model SWH-1) Sidewall vent hoods are av ...

  • Field Controls PVU-300 - page 3

    Page 3 P ROCEDURE F OR C AL CULA TIN G T OTAL E QUIVALENT P IPE L ENGTH I N F EET 1. Calculate the total equivalent feet for each type of fitting used in the v enting system from the following chart. 2. Calculate the total amount of feet fo r the straight lengths of vent pipe. 3. Add the equivalent feet for the fittings with the total amount of fee ...

  • Field Controls PVU-300 - page 4

    Page 4 8. Air flow adjustment M U ST be made t o ensure applianc e efficiency. Thi s should be done at the appliance exhaust outlet with a velocity meter, draft gau ge or by the "match test procedure". The match test is in accordance with National Fuel Gas Code A. N.S.I.Z223.1, Section 8.6. 9. On heating a ppliances not equipped with a dr ...

  • Field Controls PVU-300 - page 5

    Page 5 S IDE W ALL V ENT H OO D I NSTALLATION 1. Use the inside wall plate as a template to mark the hole location. Cut a hole 1 inch larger than the marked hole to facilitate easy insta llation (See Figure 4) 2. Center vent hood through the hole from outsid e. Fasten the vent hood to the outside wall with the appropriate type of mounting screws. 3 ...

  • Field Controls PVU-300 - page 6

    Page 6 O PTIONAL G SK -3 E XHAUST G AS S PILLAGE D ETECTOR S WITCH I NSTALLATION NOTE: Installation of the GSK-3 secondary safety switch is reco mmended for LP and Natural gas fired appliances with a draft hood. This switch will detect exhaust gas spillage out of the draft hood due to a blocked vent system and/or inadequate draft during operation. ...

  • Field Controls PVU-300 - page 7

    Page 7 GENERAL WIRING INSTRUCTIONS CAUTION: Disconn ect electrical power before wiring p owe r venter! Connect line voltage (110/120 VAC) through j unction box acce ss hole labeled "120 VAC Only". Connect l ow voltage control wiring through ju nction box access hole label ed "24 VAC Control Wiring Only". VENTER MUST BE GROUNDED! ...

  • Field Controls PVU-300 - page 8

    Page 8 Diagram E – Wiring with a 30mV Water Heate r NOTE: A CK-20FV or CK-20FG control kit MUST be added to the sy stem to properl y control the venter with the operation of a 30mV water heater. Refer to Diagra m E for proper wiring specifications. ADJUSTING THERMOSTAT ANTICIPATOR If connecting the Power Venter system to a gas appliance with a th ...

  • Field Controls PVU-300 - page 9

    Page 9 AIR FLOW ADJUSTMENTS 1. To properly adjust the venter air fl ow, loosen the inlet ring screws and open the choke plate approximately 1/2 to 3/4 open. (S ee Figure 9) Start the heating appliance following the manufacturer specified proce dure, and set the thermostat to call for heat. 2. After the system has operated for seve ral minutes to st ...

  • Field Controls PVU-300 - page 10

    Page 10 SYSTEM CONTROL CHECK PROCEDURES 1. Adjust the thermostat to cal l for heat and observe th e power ventin g system for proper operation sequence. Repeat as necessary. a. Thermostat calls for heat. b. Venter relay is energized which starts venter motor. c. Pressure switch closes whi ch allows burner to fire. d. Thermostat is satisfied, burner ...

  • Field Controls PVU-300 - page 11

    Page 11 Diagram F – Multiple Wiring with 24 VAC Furnace and 30mV Water Hea t e r MULTIPLE VENTING SYSTEMS 1. To vent a 24 VAC controlled boiler or furna c e and a 30 millivolt residential water heater usi ng one PVU power venter refer to the following. a. Follow the instructions for safe a nd proper venting previously specified in this manual. Ma ...

  • Field Controls PVU-300 - page 12

    Page 12 Diagram G – Multiple Wiring with two 24 VAC Appliances 2. To vent two 24 VAC appliances using one PVU power venter refer to the following. a. Follow the instructions for safe and proper venting pr eviously specified in this manual. Make sure that the combined gross BTU/Hr in put and equivalent vent pipe length does not ex ceed the maximum ...

  • Field Controls PVU-300 - page 13

    Page 13 Diagram H – Multiple Wiring with two 120 VAC Appliances 3. To vent two 120 VAC appliances using one PVU power venter refer to the following. c. Follow the instructions for safe and proper venting pr eviously specified in th is manual. Make sure that the combined gross BTU/Hr in put and equivalent vent pipe length does not ex ceed the maxi ...

  • Field Controls PVU-300 - page 14

    Page 14 PV SERIES POWER VENTER: VERTICAL VENTING OPTION Natural gas, lp gas or #2 fuel oil appliance rated at 75% or greater non-co nde nsing type of appliance. Maximum input temperature at power venter: 575°f Diagram I – Vertical Venting Option ...

  • Field Controls PVU-300 - page 15

    Page 15 VENTING SYSTEM OPERATIONAL INFORMATIO N Date: Heating appliance BTU/Hr input Gas valve operation pressure Vent system draft above draft hood or below barometric draft control CO 2 measurement CO measurement Appliance outlet flue gas temperature INSTALLATION INFORMATION MODEL NO.: ____________________________________________________________ ...

  • Field Controls PVU-300 - page 16

    Page 16 P/N 46517200 Rev B 11/06 ...

Fabricante Field Controls Categoría Ventilation Hood

Los documentos del dispositivo Field Controls PVU-300 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Field Controls
- manuales de instrucciones PVU-300
- hojas de producto Field Controls
- folletos informativos
- o etiquetas energéticas Field Controls PVU-300
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Field Controls PVU-300.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Field Controls PVU-300, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Field Controls PVU-300. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Field Controls PVU-300.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Field Controls PVU-300, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Field Controls PVU-300. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Field Controls PVU-300.

El manual de instrucciones completo de Field Controls debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Field Controls PVU-300 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Field Controls PVU-300, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Field Controls PVU-300 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Field Controls PVU-300 - que deben facilitarnos los primeros pasos durante el uso de Field Controls PVU-300
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Field Controls PVU-300
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Field Controls PVU-300 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Field Controls PVU-300?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Field Controls PVU-300, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Field Controls PVU-300 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Comentarios (0)