-
Zenoah G3801EZ - page 1
G3801/G3801EZ G B GB-1 G3801 G3801EZ OWNER’S MANUAL CHAIN SA W G B Or iginal Language 1 15 39 06-38 (007) ...
-
Zenoah G3801EZ - page 2
G3801/G3801EZ GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Contents 1. For Safe Operation ................................................................... 3 2. Explanation of Symbols on the Machine .................................. 5 3. Installing Guide Bar and Saw Chain ......................................... 6 4. Fuel and Chain Oil ... ...
-
Zenoah G3801EZ - page 3
G3801/G3801EZ G B GB-3 1. For safe operation W ARNING This chainsaw has been especially designed for tree maintenance and should therefor e only be used by trained operators when working on trees. 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy , or if you are under th ...
-
Zenoah G3801EZ - page 4
G3801/G3801EZ GB-4 (1) cover (2) guide bar (3) saw chain (4) nut 20. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building and potentially explosive at- mosphere. Exhaust fumes contain dangerous carbon monoxide. 21. Do not operate the chain saw in a tree unless specially trained to do so ...
-
Zenoah G3801EZ - page 5
G3801/G3801EZ G B GB-5 2. Explanation of Symbols on the Machine The port to fuel “MIX GASOLINE” Position: Beside Fuel cap The port to fill with chain oil Position: Beside Oil cap Setting the switch to the “O” position, the engine stops immediately . Position: Beside rocker switch Starting the engine. If you pull out the choke knob (at the b ...
-
Zenoah G3801EZ - page 6
G3801/G3801EZ GB-6 3. Fit the chain cover to the power unit and fasten the nuts to finger tightness. 4. While holding up the tip of the bar , adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail. 5. Tighten the nuts securely with the bar tip held up (12 ~ 15 N·m). Then check the ch ...
-
Zenoah G3801EZ - page 7
G3801/G3801EZ G B GB-7 4. Fuel and Chain Oil ■ FUEL W ARNING • Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refuel- ing the unit. Select outdoor bare ground for fuel- ing and move at least 3 m (10 ft) away from the fueling point before starting the en ...
-
Zenoah G3801EZ - page 8
G3801/G3801EZ GB-8 6. When engine has ignited, first push in the choke knob to “ST AR T” position and then pull the starter again to start the engine. 7. Allow the engine to warm up with the throttle lever pulled slightly . At once pulling throttle lever out, the choke knob is automatically returned to the “RUN” position. Keep clear of the ...
-
Zenoah G3801EZ - page 9
G3801/G3801EZ G B GB-9 1. Stop engine and screw L needle until it stops. Never force. Then set it back the initial number of turns as shown below . H needle is r estricted within the num- ber of turn as shown below . H needle : 1 3 / 8 ± 1 / 4 L needle : 1 1 / 4 ± 1 / 4 2. Start the engine and allow it to war m up in low speed for a few minutes. ...
-
Zenoah G3801EZ - page 10
G3801/G3801EZ GB-10 A log lying on the ground Saw down halfway , then roll the log over and cut from the opposite side. A log hanging off the ground In area A, saw up fr om the bottom one-thir d and finish by sawing down from the top. In ar ea B, saw down fr om the top one-third and finish by sawing up fr om the bot- tom. 6. Sawing • Before proce ...
-
Zenoah G3801EZ - page 11
G3801/G3801EZ G B GB-11 Before cleaning, the inspecting or r epairing the unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting. ■ MAINTENANCE AFTER EACH USE 1. Air filter Dust on the cleaner surface can be removed by tapping a corner of the cleaner against a hard surface. T o clean dirt in ...
-
Zenoah G3801EZ - page 12
G3801/G3801EZ GB-12 4. Spark plug Clean the electrodes with a wir e brush and reset the gap to 0.65 mm as necessary . 5. Sprocket Check for cracks and for excessive wear interfering with the chain drive. If the wear is considerable, replace it with new one. Never fit a new chain on a worn sprocket, or a worn chain on a new sprocket. Place the file ...
-
Zenoah G3801EZ - page 13
G3801/G3801EZ G B GB-13 W ARNING: This saw is equipped with one of the following low kick- back bar/chain combinations: Zenoah Part Number Saw Model Chain T ype Guide Bar Saw Chain G3801/G3801EZ 91VG 3608-52112 2932-52210 G3801/G3801EZ 95VP 2939-52110 2939-52210 side of a cutter . If a gap is observed between them, the rail is normal. Otherwise, th ...
-
Zenoah G3801EZ - page 14
G3801/G3801EZ GB-14 11. Specifications POWER UNIT : Displacement (cm 3 ): ................................................................................. 37.2 Fuel: ..................................................................................................... Mixture when using ZENOAH genuine oil (FC grade) ................................ ...
-
Zenoah G3801EZ - page 15
G3801/G3801EZ G B GB-15 Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty period, the failed part will be replaced or repair ed fr ee of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: Six (6) months after pur chased by end-user subject to 12 months from pr oduced mon ...
¿Tienes una pregunta acerca de Zenoah G3801EZ?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Zenoah G3801EZ, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Zenoah G3801EZ probablemente compartirá una forma de solucionarlo.